Search Documents

By Howard E. Parkinson

The mine pager phone to public telephone interconnect system permits mine paging telephones to be interconnected with the public phone system, thereby providing emergency and off-hours communications. The system, a push-to-talk, push-to-listen system, is compatible with any mine paging system utilizing dc voltage on the line to enable paging. A tone generator of the proper frequency enables an outside caller to page over mine pager system loudspeakers. A caller inside the mine can make an outgoing call to a preselected, preprogramed number with the use of a proper frequency tone generator. The system includes an automatic hangup timer that restricts the time off-line due to a wrong number or incorrect hangup to 20 seconds and 6 minutes, respectively.

Jan 1, 1974

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By V. F. Parry

 The amount of energy required to support a unit volume of industrial production appears to depend on the volume of industrial production, effi- ciency of utilization of fuel, the form of energy used, climate, and popula- tion served. Previous to the first World War, industries of the United States were learning how to use the vast resources of energy that were available. From 1895 to 1900 the total amount of energy produced was equivalent to 3.7 tons of 13,100 B.t.u. coal per capita, but from that period until 1920 the energy used increased steadily until it reached an average of 7.7 tons per capita. Since that time the amount used has fluctuated with business con- ditions and has averaged 6.9 tons per capita.

Jan 1, 1943

Despite the strange names given to its parts, the eye is not a very complicated organ. If you think of the eye simply as a detector of light, you will be able to understand the mechanics of central vision, peripheral vision and adaptation described below. These three processes of seeing are basic, not only to mining, but also to everyday activities. A number of simple experiments are described In this chapter to demonstrate different types of seeing processes. Try the experiments. They really make the point. Light rays reflecting from objects enter the eye through a lens and fall on the back surface called the retina. The retina 1s lined with millions of tiny light sensors called "rods" and "cones." These sensors, in turn, are connected to the brain by the optic nerve.

Jan 1, 1976

By Travis Q. Lyday

Fiji has been an independent country within the British Commonwealth of Nations since 1970. It consists of an archipelago of more than 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets, to the larger mountainous islands of Kandavu, Taveuni, Vanua Levu, and Viti Levu of volcanic origin. The islands of Fiji straddle the 1800 meridian about 1,800 kilometers south of the Equator in the part of the southern Pacific Ocean known as Melanesia. The production of gold and silver from the Emperor Mine at Vatukoula on the island of Viti Levu, the main island of Fiji, remained Fiji's only metallic mineral producer. Mining began at the Vatukoula site in 1933, producing 124 million troy ounces of gold and 147 thousand troy ounces of silver by yearend 1985.

Jan 1, 1987

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

By Fred Leighton

The Bureau of Mines monitored a rock-burst-prone pillar in a metallic ore vein, up to and through failure, to measure its reactions to increasing loads, as it was mined. Three parameters were monitored: the stress changes at chosen points within the pillar, the displacement characteristics of the drift above the pillar, and the micro-seismic activity in and around the pillar. In descending order of effectiveness, the microseismic technique, vibrating wire stress measurements, and displacement measurements reflected the pillar reactions, and all showed good correlation to one another. A major rock burst in the pillar, which destroyed about 100 feet of drift above the pillar, occurred at the end of this study. This burst was preceded by a large anomaly in the microseismic activity in the failure area.

Jan 1, 1982

By R. V. Ramani, A. S. C. Owili-eger

System Size N,NX Number of blocks in x-direction M,NY Number of blocks in y-direction NTIMES Number of systems to be simulated LENGTH Length of medium WIDTH Width of medium THICK Thickness of medium NZONE Number of material zones Medium Properties XPERM(I,J) Permeability in x-direction at the point (i,j) YPERM(I,J) Permeability in y-direction at the point (i,j) PHI Medium porosity T Medium temperature Gas Properties PURL, VISCOG Gas viscosity Z Gas deviation factor BETAG Gas compressibility coefficient Initial and Boundary Conditions IBC Initial and boundary conditions NPRESS Number of specified pressures NQUAN Number of specified quantities FACEP Face pressure RESEP Reservoir pressure

Jan 1, 1974

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By Terry J. Close

The highly-mineralized 43,700-ha Rapid River study area, on the southeast side of Hells Canyon Wilderness and west of the village of Cuprum, in Adams County, western-Idaho, was investigated in 1992 by the USBM (U.S. Bureau of Mines) in conjunction with its Idaho Land Assessment Program. The 1992 study updated data gathered during the USBM's 1974-76 Wilderness investigation. The studies consisted of the evaluation of 61 mineralized sites and the estimations of tonnages, grades, and minability of these sites. Most of the sites studied are in two mineralized locales--Windy Ridge and Jackley Mountain. A few isolated sites, peripheral to the two locales, were also examined. The 61 sites contained more than 340 mine and prospect workings, including about 10,300 meters (34,000 feet) of underground workings, plus 134 drill holes.

Jan 1, 1993

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

By Joseph B. Huvos

Said to be one of the world's most under-developed countries, Benin had a gross national product (GNP) estimated at $1 billion in 1980.2 Contribution of the mineral industry such as cement and limestone to the GNP was negligible, but exploration of mineral potential continued Minerals.-The United Nations Development Program (UNDP) conducted an investigation of three deposits from 1977 to 1980: Phosphates (Mekrou), gold (Perma), and chromite (Buem). A phosphate rock deposit containing about 4.5 million tons recover- able by opencast techniques was discovered. It was not known if the gold and chromite deposits were recoverable economically. Iron ore deposits of some 230 million tons near Loumbo-Loumbo are at present not exploitable because of lack of infrastructure in the northern part of the country. Geologic mapping with British and French assistance was also pursued in 1980.

Jan 1, 1982

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By I. D. Shah

Thermal decomposition of copper (II) sulfate (CUS04) and copper (II) oxy-sulfate (CuO?CUS04) are important steps in the overall oxidative roasting of covellite (CuS) and chalcocite (Cu2S). Nonisothermal thermogravimetric techniques were used to investigate the decomposition reactions in flowing Na and air. Thermal decomposition of CUS04 and CuO?CUS04 followed "linear" kinetics with an apparent activation energy of 55±2 and 66±3 kcal per mole decomposed, respectively. These apparent activation energies comply with those previously reported when isothermal kinetic techniques were used. The addition of oxygen decreased the rate of decomposition, while small amounts of iron which were admixed with CuO?CUS04 did not have a significant effect. Neither oxygen nor iron had any appreciable effect on the apparent activation energy of the decomposition reaction.

Jan 1, 1972

By Eugene T. Sheridan

This report presents statistical data on individual plants in the fuel- briquet and packaged-fuel industries circularized by the Bureau of Mines, United States Department of the Interior, in its 1957 annual survey. This survey revealed that 17 briquet and 23 packaged-fuel plants were active part or throughout the year. The annual production capacity of the fuel-briquet industry was 3,088,000 net tons, a decrease of 17 percent from 1956. The decline in capacity was caused in part by the permanent retirement of 4 plants and also by the reduction in capacities of 4 other plants. The rate of production of briquet plants also decreased as the industry operated at 35.8 percent of capacity compared with 40.9 percent in 1956. Every operating plant in 1957 had an annual capacity exceeding 25,000 tons.

Jan 1, 1958

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978