Search Documents

By George S. Rice

There have appeared, from time to time, comparisons of various features of coal mining practice in the United States and Great Britain. A recent, article, appearing in a British journal, points out that the American miner produces 3 1/2 times as much coal per shift as the miner, at one-half the cost, and proceeds to explain the natural industrial, and engineering causes which lead to this result. Amon« he reasons advanced. is that the American coal miner enjoys the advantage of more easily worked seams of coal, due to the fact that the coal mining industry in the United States is of more recent date than in Great Britain. The latter qualification is not correct, because where these advantages exist, they will persist. The coal beds of the United States are not buried deeply, except in the remote parts of the country, as in the Uinta Basin of Utah. The article referred to states that many of our miners are still employed on out seams reached by "adits", (which we term entries), or by vertical shafts of moderate depth. It is probable in fact that the great bulk of the coal of the United States is taken out from a depth of less than 400 feet.

Mar 1, 1920

Most laboratory sealant studies were carried out in 2.0 inch I.D. Plexiglas tubes of 9.0 inches height containing 4.0 to 4.5 inches reconstructed soil from an 0-8 or 8-16 inch soil horizon at the Lanse site. (When soil was used from the Kato site, the top soil horizon was approximately 0-4 inches. The 4-8 inch horizon was somewhat comparable to the Lanse 8-16 inch horizon.) A 20 mesh Saran or steel screen was placed over the rubber stopper with a bottom drain to a 100 ml measuring cylinder. In some earlier experiments a 1/2 inch bed of 1/4 inch pea-gravel was then added, but in later experiments this was eliminated as it showed no particular utility. Field soil samples collected by a shovel were stored in sealed containers and sieved through a 4 mesh screen just before use. (Moisture content was typically about 25% for A horizon soil and about 20% for B horizon soil.) The sieved soil minus roots was then added in increments of about 1 1/4 inches. Compaction was effected by dropping a weighted ramrod (1-7/8 inches O.D,) five times from a height of two inches. If about twenty tamps were used or if the soil columns were rapped vigorously while water-logged, compaction was high with no detectable percolation. Freezing such samples would then usually cause very slow percolation, e.g. 1-2 ml/day. Using this as a standard procedure, percolation flows were usually stablized after two to three days to rates of about 100 to 200 ml/hour. Percolate was recycled carefully to minimize disturbance of the soil surface. When percolation flows were about 100 to 200 ml/hour, various additives (sealants) were introduced to the moist column in two to three increments to maintain a slight head. Additive concentrations were usually 2-1/2% with some at 5% in earlier experiments. Typical use of 40 ml of 2-1/2% additive corresponds to 4400 lbs/acre. When no more additive was present as supernatent liquid, water washes of about 15 ml were then used several times followed by special additives as needed. More water washes were then used to maintain a head of about 1/2 inch. Percolate was collected in 100 ml cylinders to measure percolation rates in ml/hr. Turbid percolate was evaporated to determine amount of eluted latex. Percolate was sometimes checked for pH by Pan-pH Indicator Paper9,10 reading in 0.5 units. Surface tension measurements were sometimes made by a DuNouy tensiometer10 in experiments using a surfactant for pretreatment.

Jan 1, 1972

By L. C. IlsLey

A n'Ulllber or operators have installed f'lBJ!le-proot or so-called exploaion­ proot electrical outfits, under the impression that such equipments met· all of the reqiirements of the Bureau of Mines as regards safety, There a.re todq in gaseous mines a large nwnber of euipments that have not been approved by the Bureau ot Mines, and unless mod1f'iecl could not receive sucl1 approval.. These e qu.ipments represent in pa.rt the product of manufacturers whil ha.ve never submitted. equipments for insri?ction or tests. and iri pat types developed. previous to the safety work or the bureau. Sometiu.es saleimen advocate the use of unapproved. types in gaseous mines in place of Bureau of Mines approved outfits, the purchase price beini slightly less than approved types,

Sep 1, 1922

By Victor E. Kral

"INTRODUCTION The Phelps Stokes iron deposit, also known as the Iron Mountain claim, was examined by G. L. Thompson, an engineer of the Bureau of Mines, in January 1943. As a result, the Division of Geophysical Exploration 3/ made a magnetorater survey of the deposit in June 1944, and the Mining Branch included it in a,project to explore Nevada iron deposits.The Bureau explored the deposit from September to November 1944 by means of 643 feet of diamond drilling and 445 feet of trenching holes were drilled, all of which penetrated more than: 100 feet of good-grade magnetite, although nearly all the ore except that found in the first hole contained an excessive amount of sulfur. Trenching was done largely over the first two holes, PS-1 and PS-2, and exposed the full width of the ore.The deposit is in Nye County, Nevada, 7.7 miles east of Gabbs. The property was discovered in 1902 was patented in 1907. There has been no production from the property and except for the Bureau's investigation,,has not been, explored since it was patented.Magnetite is the principal ore mineral; it occurs as fine-grained particles associated with sulfides and cemented with talc and calcite."

Feb 1, 1947

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

Determine the extent of upper extremity cumulative trauma disorders (UECTD's) in the U.S. mining industry. Background UECTD's are injuries that develop gradually over a period of time as a result of repeated stress to a particular body part without adequate time between stresses for full recovery to occur. The stresses that contribute to UECTD's may occur because of the following work components: awkward position of wrist or arm, excessive manual force, high repetitions of manual movement and effort, cold environment, and vibration. Cumulative trauma injuries to the arm and hand have become an ever growing concern among safety and health professionals in a number of different industries and work settings, such as meatpacking operations, assembly-line work, and keyboarding. Mine workers arc also exposed to a combination of stressors and work design deficiencies that result in arm and hand injuries. For example, certain job tasks and environments, such as that of an underground jackleg driller, expose miners to segmental (hand-arm) vibration and cold temperatures. Operators of underground mobile equipment, such as scoops and trams, regularly have their hands in direct contact with vibrating levers and controls.

Jan 1, 1992

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

The U.S. Department of Labor?s Mine Safety and Health Administration (MSHA),through its winter alert program, warns U.S. mine operators and miners at underground coal mines of workplace hazards that can arise when the weather turns colder. MSHA records indicate that, historically, most explosions in underground coal mines occur during winter months. ?The changes in weather can increase the risk of fatal accidents,? says David G. Dye, Acting Assistant Secretary of Labor for Mine Safety and Health. ?Each miner and mine operator must take individual responsibility to eliminate the kinds of hazards that can cause fatal accidents in the workplace. Safety is not the other guy?s job?safety begins with you.? In fact, MSHA?s slogan for this year?s campaign is ?Winter Alert Starts Now and Safety Begins with YOU.? This message reminds miners and mine operators of the risks of colder weather and educates them about helping to reduce risks and hazards. ?Safety requires the joint effort of both management and labor,? Dye says. ?Everyone at the mine site must see safety as an individual value and act to ensure a safe working environment.?

Jan 1, 2006

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

Detect hazards associated with abandoned mine openings through the use of integrated geophysical technology. Background Many abandoned mines in the U.S. present hazards to the public. The first step in abatement of these hazards usually requires locating the abandoned workings. Recent Colorado legislation resulted in a concerted effort aimed at mitigating the hazards associated with abandoned mine workings. The Colorado Department of Natural Resources-Mine Land Reclamation Division (CDNRMLRD) is responsible for locating and backfilling abandoned mine openings such as shafts, adits and collapsed features. Many shafts and adits can be located by inspection, other openings give little or no surface expression and must be located by drilling, or through the use of geophysical methods. A common method used for locating underground mine workings is to drill throughout the suspected area. However, it is prohibitively expensive to drill holes at the spacing needed to detect backlilled shafts and small voids associated with caving and/or chimneying. It may also be dangerous to move heavy equipment over shallow mined-out workings. Geophysical investigations that employ only a single method have had mixed success in detecting hazardous abandoned mine land cavities.

Jan 1, 1991

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By J. C. Edwards

The Bureau of Mines developed a mathematical model that decribes the interaction of an automated breathing and metabolic simulator, or lung, with a self-contained· self-rescuer that is supplied compressed oxygen. The model can be used to predict the gas partial volumes of 0z, Nz, and COz in the lung and in the self-rescuer breathing bag for a prescribed metabolic state that characterizes the lung. Nonlinear rate equations are used to describe the temporal evolution of the gas partial volumes. A numerical procedure was established with a FORTRAN computer program to solve these equations, which correspond to a given metabolic state. Examples are presented of applications of the model to predict bag volume and bag oxygen concentration changes with time when the bag is controlled by an automated breathing simulator. Under certain restrictive conditions, the model equations can also be used to analytically pre-dict the time required for the bag to reach a maximum or minimum volume. The model equation in this latter case was extended to transi-tions between metabolic states, with transitions described as exponential growth or decay processes.

Jan 1, 1985

Promote safer and more efficient mine operations by providing communications between personnel located anywhere in the mine. Approach A radio communications system was designed which takes advantage of existing mine wiring such as telephone lines or electric power cables. The existing wiring distributes radio signals throughout the mine, making communications possible between roving miners, vehicle operators, dispatchers, and other personnel. How It Works Research has shown that medium frequency (MF) signals (300 KHZ-3 MHZ) can couple onto and re-radiate from nearby conductors. This effect is known as parasitic coupling and re-radiation. In a mine, these conductors include electric power cables, control lines, telephone lines, trolley lines, as well as metal water and air pipes Since all underground mines require these conductors for normal operations, the necessary network already exists and expands automatically as the mine is developed. A radio communication system has been developed that uses the parasitic coupling and re-radiation characteristic of MF. Using this system, whole mine radio coverage can be achieved without the need to install or maintain communication lines. The system consists of mobile transceivers for roving personnel and vehicles, and fixed-location base radio stations and repeaters.

Jan 1, 1982

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 32,270-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 50 rock and placer samples were taken during the investigation. The study area is centered about 25 km southeast of Challis, Idaho, in the Challis National Forest. According to May, 1993, Bureau of Land Management mining claim records there were no current mining claims located inside the study area. Up to 100 claims may have been located in the study area in the past. Gold, silver, copper, lead, zinc: Significant analyses, poor exposure precludes resource estimate. Limestone: More than I billion tonnes may be chemically suitable for a variety of uses, markets too distant to favor mining. Dolomite: More than 1 billion tonnes may be chemically suitable for producing magnesium metal, markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Chalcedonic nodules: Two localities in the study area may be of interest to hobbyists who cut and polish stone. There is no reported past production from the study area.

Jan 1, 1993

By W. P. Diamond, B. M. Bench, C. M. McCulloch

This Bureau of Mines report describes photolineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W - N 15° E, and N 57° W - N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W - N 20°E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W - N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

By B. M. Bench

This Bureau of Mines report describes photo lineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W -N 15° E, and N 57° W -N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W -N 20° E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W -N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977