Search Documents

Effective in the 1987 Minerals Yearbook, the following changes have been made: "Asphalt" has been deleted; "Greenland" is included in the "Potash" chapter; "Meerschaum" is included in the "Clays" chapter; and "Staurolite" is included in the "Abrasive Materials" chapter. QUARTZ CRYSTAL Cultured quartz crystal production increased significantly in 198?, following 2 years of reduced production. Consumption of domestic lascas as feedstock for cultured quartz crystal increased. Imports of lascas from Brazil also increased. Although no lascas was mined in the United States during the year, the domestic producer supplied material to consumers from company stockpiles. Specimen-quality natural quartz was very much in demand; quartz crystal for this application is discussed in the Gem Stone chapter.

Jan 1, 1989

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By Steve Iverson, Jeffrey C. Johnson, Henry Rodriguez, Rene Rodriguez, Michael Lhamond

To reduce fatalities resulting from personnel falling into voids formed above feeders in coal piles, the National Institute for Occupational Safety and Health at the Spokane Research Laboratory established a project to monitor coal surge piles to detect the formation of voids. A resistivity imaging method has been developed by GECOH Exploration, of Lexington, KY, in which a geophysical technique known as vertical electrical sounding (VES) is used to scan for these voids. VES operates by measuring the electrical field produced by a current in the ground at the bottom of the coal pile. This paper summarizes the results obtained from a field-scale test and shows that mapping voids within a coal pile is possible.

By L. A. Readdy

No text. A set of geophysical well logs for U.S. B.M. Pilot Hole "X", Piceance Creek Basin, Colorado.

Jan 1, 1977

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 6 Automatic Elevator Control Systems An automatic elevator control system, consisting of position sensing devices and a control unit, can be used to control an emergency mine hoist. While automatic elevator control systems are assembled from standard components, they are typically custom designed to suit a given customer's application. Various manufacturers contacted indicated that the price range, less installation, for a simple two-stop control system begins at approximately $2500 and can increase depending upon the type of components used, shaft depth, the type of mechanical drive used, and the maximum operating speed A partial list of elevator control manufacturers follows. They should be contacted for further details. Marshall Elevator Company Pittsburgh, P A 412 -431 -1340 Armor Elevator Company, Inc. Louisville, KY 502-361 -7181

Jan 1, 1976

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By W. I. Nelson

This paper describing the mining practices at the Engels mine is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Engels Copper Mining Co. operates two mines about 3 miles apart in Plumas County. Calif. Both mines send ore to the same mill, and the methods of the larger, or Engels mine, are described in this paper. Between 800 and 1,000 tons of 1-3/4 to 2-1/2 per cent copper ore are mined daily from this mine by a shrinkage method. Connection is made with the Western Pacific Railroad at Paxton by the Indian Valley Railroad, which is 22 miles long and operates a daily mixed train to the mine.

Jan 1, 1930

By J. E. Meacham

The U.S. Bureau of Mines investigated recovery of manganese from basic oxygen furnace (BOF) steelmaking slags because the slags represent a large potential resource of a metal for which there is no domestic production. BOF slags were leached using fluosilicic acid, a byproduct of the fertilizer industry. Manganese and iron were extracted as soluble manganous and ferrous fluosilicates while the calcium and magnesium remained in the tailings as insoluble fluorides. Treating the pregnant liquor with sodium chloride, precipitated sodium fluosilicate (Na2Sif6) which was recovered as a byproduct. Manganese and iron were precipitated as hydroxide-carbonate salts with the addition of sodium carbonate to the treated liquor. Recoveries for manganese and iron were 73 to 83 and 67 to 70 pet, respectively.

Jan 1, 1991

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Since 1990 and the publication of the Ergonomics Program Management Guidelines for Meatpacking Plants by the US Occupational Safety and Health Administration, numerous reports of companies implementing ergonomics program have been published. However, despite these numerous reports, no examples of implementing an ergonomics program in the mining industry have been reported. In 2000, NIOSH initiated a long-term project to demonstrate the implementation of an ergonomics process designed to identify and reduce exposures to ergonomic risk factors found in mining. The mine selected for this project was the Jim Bridger Mine, a surface coal mine located 35 miles northeast of Rock Springs, Sweetwater County, WY. This paper discusses how a large, surface coal mine implemented an ergonomics program and the lessons learned while doing so.

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By Harry W. Campbell

During 1983, the U.S. Bureau of Mines conducted a mineral survey of 19,700 acres that included the Fish Creek Mountains WSA (Wilderness Study Area), 15 miles southwest of the Salton Sea. Two United States Gypsum Co. claim groups in the WSA have more than .20 million tons of inferred gypsum reserves. These high-grade, surface and near-surface gypsum deposits are an extension of a gypsum bed that has been mined continuously since 1922. The Waters prospect in the central part of the WSA has large quantities of limestone suitable for many commercial uses. Sand and gravel is plentiful in the WSA in alluvial fan and ancient shore-line deposits. Limestone and alluvial deposits are not economic because similar material is closer to potential markets. No evidence of energy minerals or geothermal resources was identified in the WSA. A portion of the eastern Fish Creek Mountains WSA is leased for oil and gas exploration. United States Gypsum Co. holds eighteen unpatented placer claims in the northwestern part of the WSA. No other mining claims or mineral leases were identified in the study area. No mineral production is known from within the WSA.

Jan 1, 1986

By W. R. Huff

Yield stress and plastic viscosity values, determined from shear rate-shear stress relationships, were found to be a linear function of coal concentration for coal-water slurries containing 40, 45, 50, and 55 weight-percent of powdered coal. In the laminar region, the flow is described by an equation derived from the fact that the square root of the shear stress varied linearily with the square root of the shear rate. In the turbulent region, the friction factor was found to be inversely proportional to the velocity to the 0.12 power.

Jan 1, 1965

By James W. Townsend, William H. King

"INTRODUCTION As a byproduct of its mineral investigation program, the Bureau of Mines has developed a number of operating devices and techniques worthy of note. This paper, prepared under the direct supervision of Paul T. Alisman, chief, Salt Lake City Division, Mining Branch, and under the general supervision of Lowell B. Moon, chief, Mining Branch, reports upon ore such technique.The Wright borehole-surveying instrument developed at the Homestake mine, Lead, S. Dak., has been described in several publications. 3/ For the benefit of those to whom the publications are not available, the instrument is described here. However, this article will be concerned mainly with the technique developed by the Federal Bureau of Mines for using the instrument.In the use of the Wright borehole-surveying instrument, it was found advantageous to develop a standard practice of operation covering type of film, preparation and care of film, loading film in instrument, placing instrument in container, exposure time, unloading film from instrument, development of film, and determination of dip and strike from film impressions."

May 1, 1947

By W. Wallace, T. Ong, M. Gautam, M. Keane, S. Xing, J. Harrison

"Diesel exhaust soots were assayed in the Ames Salmonella typhimurium histidine reversion assay system using TA 98, the soots being applied as the following preparations: dispersion in dipaimitoyl glycerophosphoryl choline (DPL), dispersion in dipalmitoyl phosphatidylethanolamine (DPP!), and dispersion in dipalmitoyl phosphatidic acid (DPPA) in physiological saline, and in physiological saline without added surfactant. The extracts of soots by dichloromethane / dimethylsulfoxide (DCM/BHSO) were also assayed. Studies were performed both with and without :IQ microsomal activation of the soot preparations. The DPP! and DPPA surfactants were chosen as phospholiridz with two palmitic acid moieties esterified to a glycerol as is the case with DPL, but with hydrophilic groups having different electrophilic characters. The soots, without S9 activation, showed mutegenic activity when extracted in the conventional procedure with DCM/DMSO. The mutagenic activity of soots dispersed in DPL was quantitatively comparable to, and in some cases greater than, the activity expressed by an equal mass of soot extracted by DCM/DMSO. Soots in other surfactantpreparations, DPP! and DPPA, also expressed positive mutagenic activity. Praincubation with S9 microsomal enzyme fraction reduced the activity of solvent extracted soots, and greatly diminished the activity of DPL dispersed soots. Initial sister chromatid exchange (SCE) assays using the Chinese hamster V79 cell line indicated DPL dispersed soot also can cause SCR in mammalian cells. Results thus far suggest that surfactant suspended or ""solubilized"" respirable soot particles could provide a mechanism for transport and expression of mutagens in the lung."

Jan 1, 1989

By P. G. Clites

This study was undertaken to determine the effect of consumable-electrode vacuum arc melting on the properties of copper and to determine the applicability of the process to the production of cast shapes of copper. Ingots and castings were produced from electrolytic tough pitch copper (ASTM designation ETP), from electrolytic cathode copper (ASTM designation CATH), and from oxygen-free copper (ASTM designation OF). The products of this study were evaluated to determine the effect of the melting process on the removal of impurities from the copper and on the physical properties of the copper. The results indicate that consumable-electrode arc melting can be satisfactorily applied to the melting and casting of copper. Ingots prepared directly from electrolytic cathode copper contained slightly higher levels of impurities than are found in commercial oxygen-free copper, Excellent results were obtained with centrifugal castings of unalloyed copper, and reasonably successful static castings can be produced if proper mold and gating systems are employed.

Jan 1, 1963

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953