Search Documents

By W. E. Wallace, P. S. Mike, C. A. Hill, V. Vallyathan, M. J. Keane

Respirable quartz duet and a kaolin clay dust have been found to be of comparable cytotoxic potential in vitro on a specific surface area basis (Wallace, et a1,1985), despite the distinctly different potentials of quartz and clay for causing pneumoconiosis or pulmonary fibrosis (Sheers, 1984). A respired particle depositing in a respiratory bronchiole or alveolus will contact a pulmonary surfactant hypophase, of which a primary component is diacyl glycerophosphorylcholine, or diacyl lecithin (DPL) (Clements, et al, 1970). Several studies have found that adsorption of such surfactant suppresses in vitro cytotoxic effects of quartz dust (Marks, 1957). Subsequent phagocytosis and digestion by a macrophage may remove the coating, restoring cytotoxic potential and initiating disease processes (Iles, 1979). Adsorption of dipalmitoyl lecithin (DPL) from emulsion in physiologic saline by respirable sized quartz dust and kaolin dusts, and consequent diminution of the dusts' hemolytic and macrophage cytotoxic potential have been reported (Wallace, et al, 1985). This report presents additional data on the cell-free in vitro phospholipase A2 enzymatic digestion of dipalmitoyl lecithin adsorbed on a quartz and a kaolin respirable sized dust (Wallace, et al, 1988) to investigate mineral specific differences in the rates of digestion and of consequent restoration of dust membranolytic potential. Respirable crystalline alpha quarts used was eighty percent smaller than 5 micorometer aerodynamic diameter with a nitrogen adsorption specific surface area of 3.97 m2/g. Respirable kaolin dust was ninety percent smaller than 5 micrometer diameter and had a specific surface area of 13.25 m2/g.

Jan 1, 1988

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.

By Gerrit V. R. Goodman, Charles D. Taylor, Edward D. Thimons

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 40 ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 40 ft.

Jan 1, 1992

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The question as to whether or not the flow of water through pneumatic rock drills commonly used in this country keeps to a minimum dust disseminated into the air during drilling arose during a study of the dust-in-air conditions in Butte mines from February to July 1936 and December 1936 to June 1937 made by the Bureau of Mines in cooperation with the Anaconda Copper Mining Co., Butte, Mont, The purpose of this report is to describe the study, including some experimental work on the subject, and to give test results.ACKNOWLEDGMENTSThe help of the ventilation department of the Anaconda Copper Mining Co. in planning the study and collecting the data is gratefully acknowledged.EXPERIMENTAL CONDITIONSTests were conducted in an untimbered 6- by 8-foot crosscut in medium-hard granitic rock near the shaft station on an inactive level of one of the active Butte mines. Figure 1 shows the plan and section of the test location. Air was drawn from the shaft at the station, through the crosscut, and up through another shaft. The flow of air through the crosscut was decreased by a brattice downstream from the sampling location, so that relatively high, easily measurable dust concentrations would be obtained in the tests. Impinger samples for determing concentration of dust in the air were collected in an opening 51 inches wide, 29 inches high, and about 4o inches from the top of the rails in a wooden stopping about 16 feet downstream from the place where the test holes were drilled."

Apr 1, 1938

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

By H. W. Davis, Richard J. Lund

"In presenting the results of this survey on consumption of ferrous scrap and pig iron for the year 1935 the Bureau of Mines, responding to requests from industry, seeks to fill a major gap that has long existed in the field of metalliferous raw-material statistics. This type of information is designed to meet the needs of: (1) Consumers of ferrous scrap. including operators of blast furnaces, steel mills, ferrous foundries, and rolling mills; (2) marketers of scrap iron and steel, including large brokers who sell, and dealers who collect, prepare, and sell the material; (3) large scrap producers; (4) producers of iron ore, with which scrap competes indirectly; and (5) other individuals and agencies interested in more general economic analysis, since the scrap market has repeatedly been cited as one of the most sensitive of all industrial barometers, If the survey prover as useful as now seems probable, it will be continued annually with possibly an enlarged scope of treatment.The Bureau appreciates that its first efforts in this field may not meet all expectations: but it hopes to develop gradually, through suggestions, advice, and criticism from the industrial groups most interested, a type of analysis that will accord closely with technical processes and best meet the needs of all groups vitally interested in supplies and use of ferrous scrap. Constructive criticism and suggestions from industry regarding improvements to be desired in the conduct of future surveys on this subject will therefore be warmly received by the Bureau."

Nov 1, 1936

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By H. Tomlinson

The development of the Sevier Valley Coal Co.'s mine marks the opening of the Salina Canon coal district in Utah. The mine is favorably located with respect, to the existing markets of the West, and if the present estimates of the amount of workable coal in it are accurate it has many Important advantages in favor of its development. This mine is situated 18 miles east of the town of Salina, Sevier County, Utah, which at present is the nearest shipping point oh the Marysvale branch of the Denver & Rio Grande Western Railroad, and is about 152 miles south of Salt Lake City, which is the distributing center for much of the coal from the Carbon - Emery coal field and is the place from which nearly all Utah coal shipped to San Francisco and points on the northern Pacific coast has a common haul.

Jan 1, 1930

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982

Aid mine workers in detecting hazardous roof conditions in underground mines by developing a method of roof sounding which supplements or replaces the traditional roof sounding technique where the miner relies on experience to determine whether or not the rock is sound. Approach The Bureau of Mines developed an electronic roof sounding de-vice that acoustically determines the integrity of mine roof rock by "listening" to the variation in frequency vibrations within the rock. How It Works n previous research, the Bureau of Mines found that loose rock in a mine, when impacted, vibrates at a much lower frequency and for a lower time period than does a solid slab. By quantifying the enhancement of low frequency vibrations in loose rock over solid rock, a repeatable, objective measure of the rock's soundness can be obtained. This approach was used in developing the rock stability tester.

Jan 1, 1986

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By E. William Rossi, Sean Gallagher, Richard L. Unger

The purpose of this study was to examine the lifting capacity of low-seam coal miners in four restricted work postures (roof heights of 36", 40", 44", and 48"), investigate the associated metabolic costs, and to examine electromyographic (EMG) data from eight trunk muscles during the lifting procedure. Subjects were thirteen underground miners accustomed to handling materials in restricted work postures. Each subject performed two twenty-minute periods of asymnetric lifting in each of four postures during the day of testing. The. frequency of lifting was 10 lifts per minute. A specially designed lifting box incorporated microswitches in one handle of the box and another in the bottom of the box, in order to examine the trunk muscle function at specific points during the lfting cycle. The data collected will be used by the Bureau of Mines to make recommendations for lifting materials in low-seam coal mines.

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By H. H. Fukubayashi

This Bureau of Mines report describes the development of a pyrometallurgical process for the recovery of the zinc and lead contained in brass smelter flue dusts, which constitute a recycling or disposal problem. Tests on brass flue dust from several sources were made in a quartz tube, heated by an electric furnace to temperatures as high as 1,050° C. The dusts were mixed with carbon and heated in an oxygen-free atmosphere. It was demonstrated that 98 pct of the zinc and 12 to 25 pct of the lead, both in the metallic state, could readily be removed from the dusts. It was also found that 75 pct of the zinc could be recovered, with less than 0.1 pct of the lead, in the absence of chlorides. Pelletization techniques were investigated and 0.6 inch pellets were found to be optimal. Pelletizing results in a tenfold reduction in volume.

Jan 1, 1974

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By Sarah P. Guerrino

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed ?mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1987