Search Documents

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

By Jr. Flynn

"The Bureau of Mines receives and answers many requests for information on the qualities and properties of American coals, and also publishes many papers that deal with coal characteristics. Compilations of chemical analyses of coal from specific locations are contained in a series of technical papers,2/ by States, whereas typical analyses of coal seams, by States and counties, are given in data books, volumes 1 to 7,2/ by producing districts, as defined in the Bituminous Coal Act of 1937. Bulletin 446, ""Typical Analyses of Coals of the United States,"" condenses and supplements these data books, which do not apply to the Western States. Other coal properties are described in numerous publications listed in the Bureau of Mines Bibliography of Publications. However, no recent publication lists average B.t.u. values by rank on a Statewide and national scale. Averages have been estimated in the past, and some of them are included in this paper for comparison.The average and the ranges of as-received B.t.u. values of American coals on a Nation-wide basis, as found by the statistical method described in this paper, are given in table 2 and on a State-wide basis in table 3. The following is abstracted from table 2:In deriving average B.t.u. values for coals, the results depend on the type of data available and the methods of calculation. The data, or analyses, may represent any of three types of samples - mine, tipple, or delivered. In mine sampling, a channel cut is made of a vertical face of the coal bed, carefully excluding most of the impurities, and the material retained is the sample. It is readily seen that mine samples are selected samples and do not strictly represent the unmined coal bed, unless the coal contains no major impurities. Mine samples generally represent the best-quality coal that could be produced. In contrast to mine samples, tipple and delivered samples represent coal that actually has been mined, and their analyses may show either lower or higher values than mine samples of the same coal, depending on treatment and preparation after mining.Of the thousands of analyses accumulated by the Bureau of Mines, most are of either tipple or delivered samples and represent the coal after it has been mined. Any average calculated from this aggregate of data will, consequently, reflect coal that has been produced, and not unmined coal in situ.The method of calculating an average from the basic data also will have considerable influence. If there are three seams of coal in a county, the average analysis for the county is not necessarily the arithmetic mean of analyses of the three individual seams. For a probable average of unmined coal, the B.t.u. values of each seam should be weighted in proportion to the unmined reserves of each seam. In similar manner, an average for past pro¬duction should be weighed according to the past production for each seam. Figures for coal reserves are only estimates based upon geologic evidence and its interpretation. Production records are much more accurate than estimated reserves, although detailed production records for individual seams by counties are very few."

Dec 1, 1949

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By C. B. Manula, R. L. Sanford, R. A. Rivell

Data input is divided into three divisions for discussion purposes below. These divisions are: a) Information Retrieval and Control Options; b) Gaming Options; and c) Descriptive Parameters. The data input for model application, which is listed in Appendix B, is segmented to show the location of these divisions. In actuality, however, these divisions form a continuous data file. Each 80 character record of data input is edited by an alpha¬numeric editing routine which permits the format free numerical speci¬fication in most data divisions. The editing routine searches each record for numeric types and when found, converts these numbers into computational forms. The Fortran convention of decimal and integer numbers is not used by the editor so that a number may appear on the data record in either form desired by the user. Since the editor seeks only numeric types, the input records may be freely commented and identified with alphabetic letters (A - Z). One or more input records may contain only commentary information or be entirely blank. On the other extreme, any data record may contain up to 40 numeric elements, each separated by a blank space. The application of this capability can be seen by reference to the data. Information Retrieval and Control Options The information retrieval options specify the detail of infor¬mation required to be printed. These have been placed in a separate data division, identified on the data record by option name for use

Jan 1, 1974

By Louis A. Panek

This report deals with the combined friction and suspension effects in the reinforcement of horizontally bedded mine roof by bolting. Other reports have treated these two effects separately. Friction effect refers to the reduction of bending in a laminated roof due to the clamping action of tensioned bolts. If the beds tend to have unequal deflections, the bolts oppose this tendency, thus creating a suspension effect, which consists of a transfer of part of the weight of weaker or thinner beds to the flexurally more rigid beds within the bolted unit. The combined effects of friction and suspension on the bending of the beds, whether an increase or a decrease, are difficult to generalize because they depend on the bedding sequence and the bolt pre-tension. Some analysis of the bedding sequence usually is required to determine the critical bed within a set of bolted beds. However, if the suspension effect is substantial and if the bolts are pre-tensioned, then the greatest bending stress is likely to occur in the thickest bed. Findings are based partly on theory and partly on tests of mine-roof models in a centrifuge, which were found to verify the theory. Mathematical formulas are obtained for the change in maximum roof bending stress and for the change of roof deflection due to the combined friction and suspension effects. The maximum bending stress is needed for designing a roof-bolting system and the deflection for evaluating its effectiveness.

Jan 1, 1962

By Van H. Manning

PETROLEUM INVESTIGATIONS. The work of the petroleum division of the Bureau of Mines during the period of the war was under the supervision of Chester Naramore, chief petroleum technologist. In its petroleum investigations the bureau cooperated freely with other Government bureaus and acted as a source of information on petroleum matters. COOPERATIVE WORK ON INTERALLIED PETROLEUM COMMISSION. On July 15, 1918, Mr. Naramore and W. E. Perdew, chemical en- gineer of the bureau, left for London to act as representatives of the United States Fuel Administration and the United States Shipping Board on the Inter-allied Petroleum Commission. Numerous con- ferences were held with representatives from France, England, and Italy on specifications and requirements of the various allied Govern- ments for petroleum products, and for this purpose meetings were held in London, Paris, and Rome. EXAMINATION OF PETROLEUM FACILITIES IN FRANCE. The storage facilities and the transportation system in France were studied, and recommendations based on the information gained were made to the director of the oil division of the Fuel Administra- tion and to the chairman of the Shipping Board. Refinery plants in France were inspected, as well as filling stations and shipping facilities from ports in France and Italy to the various fronts and the petroleum base of the American Expeditionary Force at Romorantin. France. At the request of Ambassador Sharp, a re- port was prepared on the advisability of developing the petroleum resources in France.

Jun 1, 1919

By John C. Machisak

THE INJURY data and related employment experience of the coking industry in the United States for 1955 arc presented in this publication under the following general sections: (A) General Injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, injury-frequency rates, and accident agencies involved in causing injuries. Data are tabulated for the industry as a whole, for each typo of oven: and for the States in which coke is produced.

Jan 1, 1958

Improve surface mine haul-age truck safety and efficiency by providing a means for sensing the weight and distribution of the truck's load. Approach The safety hazards and the economic implications of overloading mine-haulage trucks were analyzed to determine the net effect of that practice on mine operations. The analysis indicated that: Ten to 25 pct overloading is typical; Higher haulage, tire, and maintenance costs occur due to overloading (a 20 pct overload was estimated to increase operating costs 7 pct per ton); Ten to 15 pct of haulage? truck injuries and fatalities are attributable to overload conditions, at a cost over one million dollars per year to the mining industry. Vehicle-weighing technology that conformed to the performance specification for an off-highway haulage truck overload detection system was selected for in-mine testing. How It Works Normally, volumetric estimates are made during the loading sequence which do not account for the varying ore density. Hence, the actual weight of a load is never precisely known. By providing a precise measurement, an overload detection system will not only indicate vehicle overloading, but will also show under-utilization of the truck. One system tested by the Bureau of Mines was the ?Load Analyzer" manufactured by Pactronics Corporation in California. This system consists of a meter-type analog readout for the cab console and three "Electrosensors" (linear variable differential transformers) attached to the main frame. Using conventional welding and brazing techniques, two sensors are attached between the front members of the engine sub-frame and the top of the left and right trailing arms (one sensor per arm). The same techniques are used to attach the third sensor to the rear centerline of the truck. between the main frame cross member and the A-frame. The readout unit on the cab console indicates by color-coding whether each sensor loading is under (green), at (yellow), or over (red) the pre-set rated load. The three-sensor configuration with in-dependent readouts also detects uneven distribution of the load.

Jan 1, 1984

By Kenneth L. Cashdollar

While underground coal technology has progressed over time, regulations on coal dust have not kept up ? the most recent rules are more than 80 years old. The National Institute for Occupational Safety and Health and the Mine Safety and Health Administration conducted a joint survey recently on coal particle ranges as measured in US coal mine samples. In underground coal mines, dust explosions are prevented by the addition of enough rock dust (usually limestone) to make the total dust mixture inert. The rock dust acts as a heat sink for the dispersed dust mixture by reducing the temperature below the value needed to propagate an explosion. Federal regulations require 65% in combustible content in intake airways and 80% incombustible content in return airways, where the coal dust is assumed to be finer in size. The regulations also require an additional 1% incombustible for each 0.1% methane in the ventilating air in intakes and 0.4% additional incombustible for each 0.1% methane in returns.

Jan 1, 2008

By R. V. Ramani, P. M. T. White, D. Sutton

4.1 Introduction Using methods outlined in previous sections of this report, programs were written and/or obtained to: i) select best combinations of "a" and "k" for up to 8 different value parameters, ii) calculate available and unavailable ore tonnages and other statistics, and iii) produce contour maps of various parameter characteristics and available tonnages on a line printer. All the above programs are written in Fortran IV for execu¬tion on IBM 360/370 computers. 4.2 Calculation of Coal Reserves The Ore Reserve program suite consists of the following sections: (a) UNIT 1: This unit is a subroutine called by Unit 2 to determine values for "a" and "k" from the given data. (b) UNIT 2: These programs calculate ore reserves and are composed of a main program and several sub¬routines. In the following, their functions are abbreviated: i) MAIN - calls subroutines, reads run parameter variables, reads borehole data and interpolates grid node values for the area of investigation

Jan 1, 1974

By Oliver C. Ralston

OUTSTANDING TRENDS of the year included the following: 1. Concentration and beneficiation of iron ores to provide improved blast-furnace feed and extend ore reserves. 2. Successful development of pelletizing and sintering procedures for fine iron ores. 3. The realization that cyclone separation could replace existing classifiers in many grinding circuits. 4. The rapidly blossoming metallurgy of ultrapure silicon and improvements in zone melting. 5. The rapid increase in the use of liquid-liquid extraction and ion exchange in hydrometallurgy. 6. The industrial application of vacuum melting on the 100-ton scale. 7. The hope for developing a columbium (noibium) base alloy for high-temperature use. The technologic advancement in metallurgy that had the greatest effect on the American economy was the beneficiation of iron ores to give improved feed for blast furnaces and indirectly extend our ore reserves. This was not a sudden development but rather culmination of a decade of intensive effort.

Jan 1, 1958

By Kevin Connor

Exports of agricultural products, mostly coffee, continued to account for more than 90% of Burundi's foreign exchange revenue. The country's ban on commercial mining was lifted in 1987. Mining of peat for fuel, limestone for agriculture, and clay for insecticides continued as in previous years. At yearend, Burundi's external debt stood at almost $700 million.2 Amoco Burundi, a subsidiary of the Amoco Petroleum Co., drilled two exploration wells in northern Lake Tanganyika in 1987. No oil was found, but preliminary findings were encouraging enough that further seismic surveys and offshore and onshore drilling exploration were planned in 1988. Any oil or gas finds would have substantial impact on the Burundian economy because a major portion of the country's trade deficit was directly attributable to petroleum and gas imports. The Zaire Government agreed in June to let Amoco Burundi explore Zaire's side of Tanganyika using the same equipment and personnel being used in Burundi.

Jan 1, 1989

By Ronald S. Conti

Fire is a major concern for those who work in underground mines. A mine fire can occur at anytime and often results in a partial or total evacuation of mine personnel and could result in the loss of lives. Therefore, having a workforce that is well trained to prevent, detect, and fight a fire is important. This paper focuses on responders’ preparedness for fire. Responders in this context are considered the entire workforce and are categorized as first, second, and sustained responders and evacuating miners. Quality training enhances ones awareness of mine fire hazards and promotes self-confidence in combating fires and responding to emergencies. Early warning systems and other escapeway aids such as a through-the-earth signaling and communication system, lasers and strobe lights are also addressed. The technological advancements that have been made can improve the state-of-preparedness for responders to underground emergencies and increase the chances of survival for escaping personnel.

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968