Search Documents

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

By Susan B. Bealko

Mining provides a large part of the energy and raw materials that feed this Nation's economy. Copper pipe, concrete, and window glass serve as well known examples of the reliance on minerals in modern society. Less appreciated, but as important, are the hundreds of mined commodities that are an integral and necessary part of everyday products, ranging from medicines and computers to carpet and paper. Coal is a major portion of the country's energy mix today, as it will likely continue to be in a future hydrogen-based economy. The domestic mining industry also provides strategic minerals that are important for the Nation's security. The processes to recover these mineral commodities are among the most demanding and complex in an industrial society, and this inherently dangerous industry has historically had the highest risks of fatality and injury. The mining industry has been undergoing some trying and challenging times because of the recent mine disasters in the coal fields. These events have been alarming in light of the strong and encouraging safety record that has characterized mining in the United States for most of the past decade. While mining communities deal with their grief, mine operators, government regulators, and other safety personnel, set about trying to determine why these fatalities occurred. Subsequently, the mining industry is currently experiencing changes in legislation at an unusually rapid pace. The most recent regulatory changes are the Mine Improvement and New Emergency Response Act of 2006 (MINER Act) and the temporary emergency standard for mine seals. The new mine safety laws call on the nation's mines to adopt certain procedures and safety technologies immediately, or as soon as they become commercially available. Putting all the provisions in place from these new laws is a major undertaking, and will necessitate strong collaborations and partnerships among mine operators, manufacturers, regulatory and research agencies, labor unions, and community groups. It is against this background that Prevention through Design (PtD) components for the Mining Sector are recommended.

Jan 1, 2008

By P. T. Brooks

The selective recovery of nickel and cobalt from impure raw materials is being investigated by the Bureau of Mines as part of a program to develop improved procedures for preparation of pure metals. A combination solvent extraction-electrolytic process has been developed in the laboratory that enables preparation of high-quality nickel and cobalt from nickel oxide containing, in percent, 76 nickel, 0.8 cobalt, 0.5 magnesium, 0.2 iron, and lesser quantities of copper, zinc, and other metals. The oxide was smelted, using carbon as reductant, and cast into anodes. These anodes subsequently were dissolved in diaphragm-type electrolytic cells. Nickel and cobalt were deposited separately from appropriate electrolytes, concurrent with dissolution of the impure anodes. Anolyte containing nickel and cobalt in the form of chlorides and sulfates was treated for removal of impurities and separation of nickel and cobalt. First, iron and aluminum were removed as hydroxides by adding nickel hydroxide to raise the pH of the anolyte from 2.3 to 4.5. Next, the pH was adjusted to 2 by adding hydrochloric acid, and the solution was treated by solvent extraction to separate nickel and cobalt.

Jan 1, 1963

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

By R. B. Stroud

Bureau of Mines studies of copper-bearing Permian red beds, which extend from north-central Texas through western Oklahoma to southwestern Kansas, indicate heretofore undefined commercial possibilities for low-grade, medium-volume, strip-mining operations. Potential ore bodies are indicated containing 0.5 to 1.5 percent copper in zones 6 to 12 inches thick. Cost analysis studies indicate a commercial operation is feasible for a hypothecated 1,000-ton-per-day ore mining and milling complex where a maximum of 60 feet of overburden can be stripped in mining a seam of shale 12 inches thick containing 1.2 percent copper

Jan 1, 1970

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

Spectrochemical methods were developed to determine beryllium in the concentration range 0.0015 to 4.0 percent in siliceous mineral beneficiation products. Two methods are described. They are (1) a fusion-pellet-spark procedure (spark method) and (2) a sustaining alternating-current arc procedure (arc method). In the spark method the sample is fused with lithium tetra-borate and vanadium pentoxide. The resulting bead is crushed, mixed with powdered graphite, and briquetted. This is analyzed spectrographically using controlled high-voltage spark excitation. In the arc method the sample is diluted with germanium metal, graphite, and vanadium pentoxide. Weighed charges are packed into cupped graphite electrodes and subjected to excitation with a sustaining alternating-current arc. Vanadium serves as internal standard for both methods. Effects due to matrix variations in samples and standards are eliminated either by fusion with lithium tetraborate in the spark method or by dilution with germanium and graphite in the arc method. Beryllium determinations show deviations from accepted chemical values of approximately 5 and 8 percent for the spark and arc methods, respectively. Analyses can be made more rapidly by the arc procedure with a sacrifice in precision and accuracy. Either method can be applied to the determination of beryllium in silicate rocks.

Jan 1, 1962

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

By D. Debasis, Christopher Mark, Gregory M. Molinda

The stability of any underground opening is, in large part, a function of the strength of the rock mass which surrounds it. The Coal Mine Roof Rating (CMRR) has been developed to quantify the defects in the rock mass and compile a strength value which can be used for engineering design. The CMRR has been applied to a number of ground stability problems, including chain pillar design, roof bolt selection, hazard assessment, intersection design, and numerical modeling. The CMRR procedure and some of these applications are described in this paper. The CMRR will soon be available in a Visual Basic computer program, allowing easy integration into exploration programs and standard roof fall assessments.

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By G. P. Sturm

This work was undertaken by the Bureau of Mines in cooperation with the Environmental Protection Agency to determine photochemical specific reactivities of emissions from automobiles using leaded-premium-and regular-grade fuels and prototype lead-free fuels of comparable octane quality. Emissions were photoirradiated in a 100-ft3 environmental (smog) chamber constructed of aluminum and Pyrex glass at three sets of initial hydrocarbon (HC) and oxides of nitrogen (NOx) concentrations. Reactivity was measured and expressed in terms of rate-of-NO formation (RNo2) and dosages of oxidant, peroxyacetyl nitrate (PAN), peroiypropionyl nitrate (PPN), and formaldehyde (HCHO). The results indicate that the evaporative emission samples and the evaporative plus exhaust emissions samples from the lead-free fuels have, in general, higher reactivities per gram than those from the leaded fuels. For the samples containing only exhaust emissions, the only trend observed was the lower specific reactivity exhibited by the leaded premium fuel exhaust. These differences in specific reactivity are taken to reflect the differences in hydro-carbon composition of the fuels and their evaporative and exhaust emissions rather than any difference in lead content per se.

Jan 1, 1973

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By D. E. Shanks

As part of its effort to produce cell-grade alumina from clay, the Bureau of Mines investigated the hydrogen chloride gas-sparging crystallization of aluminum chloride hexahydrate (ACH) from aluminum chloride liquor, to provide information for optimizing the crystallization operation. Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities, particularly phosphorus and magnesium, in ACH crystals are (1) aluminum chloride concentration in the feed solution to crystallization, (2) hydrogen chloride gas flow rate, (3) temperature, and (4) concentration of phosphorus and magnesium also in the feed solution. Parameters 1, 2, and 3 affect crystal formation. The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth. Aluminum chloride hexahydrate of cell-grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt-pct P205 and 0.010 wt-pct MgO. Crystallization temperatures less than 600 C decreased crystal purity.

Jan 1, 1981

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By W. H. Young, R. L. Anderson

"Physical conditions, such as thickness and character of the coal seam, dip or pitch of the seam, depth of cover, character of roof and overlying strata, mine water, etc., affect the productivity in bituminous-coal mining. Thickness of the coal seam being mined is probably the most important single item that determines whether the output per man per day shall be low or high; however, in strip mining the depth of cover or overburden to be moved is of equal importance.Bituminous coal is mined today from seams of exceedingly variable thickness - less than 2 feet to more than 50 feet; however, a large majority of the mines are producing .coal from seams 3 to 6 feet thick. The average thickness of the coal seams mined in the United States has not changed materially in the past 25 years. The average seam thickness for all bituminous-coal mines was 63 inches in 1920 4/ and 65 inches in 19)45. As thick seams have been exhausted in the older fields, other thick seams, have been opened in the newer fields.Productivity increased from 4 net tons per man per day in 1920 to 5.78 in 1945. This 45 percent increase in productivity resulted from increased mechanization. The percentage of underground production represented by coal cut by machines increased from 61 in 1920 to 91 in 1945 Mechanical loading increased from less than 1 percent of underground production in 1920 to 56 percent in 1945, and strip mining increased from less than 2 percent to 19 percent of the total production during the same period."

Dec 1, 1947

By J. E. Hamak

This publication contains analyses and related source data for 144 natural gas samples from 19 States. Of the total samples, 139 were collected during calendar year 1990. The remainder were collected earlier, but releases granting permission to publish were not received until 1990. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free-market economies. This survey has been conducted since 1917. The analyses were made by mass spectrometer and chromatograph.

Jan 1, 1991

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By J. M. Gomes

The Bureau of Mines investigated electrolytic techniques for preparing diborides of the group IV B metals. TiB2, ZrB2, and HfB2 were electro-deposited from their respective oxides dissolved in borate-chloride-cryolite electrolytes. Titanium diboride was also electrodeposited from rutile (Ti02) dissolved in a Na2,B4O7-Na2C03-Na3A1F6-NaC1 electrolyte at 1,050° C; 14 kW-hr were required to produce 1 pound of TiB2. Major impurities in the TiB2 produced in a 10-deposition cycle experiment, in weight-percent, were Al, 0.2; Cr, 0.3; Fe, 0.1; V, 0.3; C, 1.4; and 0, 1.0. Zirconium diboride was electro-deposited from zircon (ZrSiO4) dissolved in a Na2B407-NaOH-Na3A1F6-NaCl-NaF electrolyte at 1,050° C. The ZrB2 produced in a 10-deposition cycle experiment contained the following impurities in weight-percent; Fe, 0.1; Si, 0.5; C, 0.3; and 0, 0.6. Energy required to produce 1 pound of ZrB2 was 9.3 kW-hr.

Jan 1, 1975