Search Documents

By J. R. Ruark

This report presents results of mining operations and of research and development work done during stage I of the gas combustion retorting research program conducted by the Colorado School of Mines Research Foundation and six major oil companies at the Bureau of Mines Anvil Points Oil Shale Facilities. A brief description of the gas combustion process is given and the experimental program is discussed. Included in this discussion are (1) air-gas distributor development, (2) results of gas and shale distribution studies, and (3) effects of other process variable studies. The report concludes with a statistical evaluation of experimental results. Two appendixes present a chronological account of the experimental work and tabulations of data for all retorting runs conducted during stage I.

Jan 1, 1969

By S. Ralph Austin

This Bureau of Mines investigation determined the effects of so-called annealing at high temperatures on radon-222 emanation from domestic uranium ores. Concurrently, a method was developed for closely estimating the emanation coefficients of hot samples from measurements of their gamma activity after cooling. Emanation coefficients of 102 samples from 14 domestic areas of past, present, and possible future uranium production were investigated using modifications of the closed-can, gamma-only assay method at and after cooling from 100° to 1,000° C. True annealing probably does not occur below 500° C. In limited investigations at 500° C and above, effects of annealing are masked by the effects of other parameters. Emanation is commonly less at one or more of the steps investigated in the 100° to 500° C range than before heating. This decrease is tentatively attributed to water loss at temperatures dependent upon the minerals present. The average sample emanates least at 300° C; emanation increases with higher temperatures to at least 900° C. Emanation decreases sharply on cooling, but it is partially restored by prolonged exposure to the atmosphere at room temperature. Higher than average emanation of coffinite ores at 500° C and above may be related to destruction of the coffinite crystal structure.

Jan 1, 1979

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By H. J. Heinen

This report summarizes preliminary research studies by the Bureau of Mines in electrowinning molybdenum directly from pure or impure molybdenum trioxide (MoO3) by fused-bath electrolysis in an open graphite cell without need of a protective inert atmosphere. A formulated electrolyte of the tertiary system containing 41.6 percent sodium pyrophosphate, 16.7 percent sodium tetraborat, 33.3 percent sodium chloride, and 8,4 percent molybdenum trioxide, by weight, electrolyzed at 1,000° C,, gave excellent results. Current density studies were made over a range from 20 to 260 amperes per square decimeter. Current efficiencies of 80 to 90 percent were obtained over the entire range. Yields up to 500 grams of molybdenum per kilowatt-hour were obtained. Higher current densities, however, reduced yields and produced a finer grained metal. The two most important facets in electrowinning molybdenum from MoO3, in an open cell, are temperature and electrode spacing to minimize or eliminate the formation of the suboxide MoO2, the major source of oxygen contamination. At temperatures of 1,000° C. and higher, together with the proper spacing of the electrodes, formation of oxides are practically eliminated. Molybdenum metal electrowon from pure MoO3 was 99.9 percent pure and contained 0,056 percent oxygen and 0,007 percent carbon. This metal, when arc-melted, had a Vickers hardness number of 175 and contained 50 parts per million oxygen and less than 10 parts per million carbon. Molybdenum metal electrowon directly from an impure MoO3 containing 90 percent MoO3 resulted in a metal of 99.8 percent purity.

Jan 1, 1961

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By H. B. Brunot, L. C. IlsLey

The design , construction, inspection , and test for permissibility of a storage- battery locomotive outfit in accordance with the requirements of Schedule 15* represents a large amount of work, first on the part of the locomotive manufacturer and secondly on the part of the Bureau of Mines . Detailed information of the first investigation under the schedule is presented here . This investigation covers the inspection and test of a storage- battery locomotive manufactured by the Geo . D. Whitcomb Co. , Rochelle , Ill . , to which Approval No. 1500 was assigned ,

Feb 1, 1923

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By E. C. Tarpley

The Federal Bureau of Mines has studied solvent extraction as a means of concentrating the mineral components in coal. Solubilities of a number of American coals were determined using abietic acid as a solvent. The effect of rank on solubility was investigated, and maximum solubility was found with coals of intermediate rank. Vitrinite is the most soluble petrographic component; fusinite, micrinitc, and exinite are nearly insoluble. Spore exines also have a low solubility. Abietic acid is a hydrogen donor and reduces pyrite to ferrous sulfide. Mild hydrogenation of high-molecular-weight fragments of the coal structure to those of lower molecular-weight probably contributes to the solvent action. Even where solubility of the coal substance exceeds 90 percent, contamination of the mineral matter with coal makes identification of the mineral components difficult. Further separation might be possible by the application of float and sink techniques to the residue. INTRODUCTION Work n the solvent extraction of coal is conducted to recover commercially useful products and to characterize coal;. and obtain information on their structure. Some coals, particularly those of low rank, contain waxes, resins, and humic acids which can be removed by solvent extraction and find varied industrial uses. In World War II, solvent extraction of coal was conducted on a commercial scale in Germany to obtain a low-ash feed material for hydrogenation and to produce electrodes carbon for the aluminum industry.4 5/

Jan 1, 1960

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By Bernard Porter

The rate of the heterogeneous reaction between reactor-grade yttrium and lithium fluoride in lithium fluoride-yttrium fluoride mixtures was measured using a quartz spring balance. At 950° C the magnitude of the rate of reaction is 10-5 grams of yttrium/cm2-sec. The heat of activation for the reaction is 38.3 kilocalories per mole of LiF. A surface-controlled mechanism is proposed in which LiF is adsorbed on the yttrium metal surface. An activated complex is formed when additional LiF reacts with the adsorbed LiF-metal site. The activated complex then decomposes to the products) which are lithium metal and YF3. The importance of the reaction in the electrowinning of yttrium metal from fluoride electrolytes is discussed.

Jan 1, 1967

By L. J. E. Hofer

The Bureau of Mines determined rates of adsorption and desorption of methane as a function of particle size and temperature, using coals from the Pocahontas No.3 seam (lvb) from the Bishop mine of western Virginia, and the Pittsburgh seam (hvab) from the Pursglove No. 15 mine of northern West Virginia. For a given coal sample and temperature, the rate curves for adsorption and desorption are essentially the same when expressed on a fractional approach to equilibrium basis. The rates of adsorption and desorption increased eightfold as the particle size was decreased from 6-8 to 270-325 mesh per inch. The adsorption process appears to be diffusion controlled. Rate of sorption processes increased with increasing temperature; however, the amount adsorbed at equilibrium decreased.

Jan 1, 1966

By G. B. Goodman, W. H. Pailes, P. D. Kaplan, I. Stachura, V. Castronova

"The risk of developing silicosis in underground coal miners, tunnel workers and some foundry workers is well-known. These persons generally develop the classic form of the disease over a prolonged period of time. Workers involved in abrasive blasting of bridges and those polishing tombstones have been reported to develop an acute form of silicosis within a few years of commencing exposure. Not well-appreciated is the potential for development of acute silicosis among drillers at surface coal mines. We report the case of a 33-year--old man who worked primarily at surf ace drilling, developed acute silicosis within three years of beginning exposure, and who initially responded dramatically to corticosteroid therapy. CASE REPORTThe patient is a 33-year-old white man who worked as a rock driller at a quarry and also at surface coal mines in western Pennsylvania since 1975. Prior to 1983, much of his work was done with a wet process in which water was applied to reduce dust generation. After 1983 he worked primarily as a driller at a surface coal mine using a dry process. He never wore a respirator. He described the dust as being so dense that he ""couldn't see anything.- In August 1986, he presented to his local physician with a complaint of pleuritic chest pain and shortness of breath. A chest x-ray film was obtained showing only a few p and q opacities. He continued working and these symptoms subsided, but the patient noted the onset of progressive weight loss. By May 1987, he had lost approximately 50 lb. In addition, he suffered profound malaise, dyspnea, migratory chest pain and arthralgia, fevers and drenching night sweats.A course of erythromycin therapy given in the hospital resulted in only fleeting improvement. Studies for Legionella and Mycoplasma infections were negative, as was a tuberculin skin test. The patient was transferred to Allegheny General Hospital in Pittsburgh on June 4, 1987.There was no history of serious medical illness, including tuber¬culosis. The patient admitted to smoking between I and 1 1/2 packages of cigarettes daily for 2 1/2 years prior to May 1987 when he stopped smoking. He denied intravenous drug abuse, homosexual activity or receiving transfusions of blood or blood products.On physical examination the patient was a thin, febrile white man who appeared chronically ill. Bilateral axillary and cervical lymphadenopathy was present. Chest examination showed restricted expansion and bilateral crackles. Examination of the heart and abdomen disclosed no abnormalities."

Mar 1, 1992

By Ernest L. Corp

Seepage forces computed by a finite-element flow program are combined with gravity forces in an elastic-plastic stress-analysis program to determine the stability of mine-waste slopes. Computer output provides a cross-sectional plot of the dam or embankment showing the safety factors for each element. The combined finite-element program called SEEP-SLOPE was used to analyze several trial embankments and the 1972 Buffalo Creek Dam failure Safety factors computed by the finite-element method (FEM) were compared with those computed by Bishop limiting-equilibrium method. For individual slip circles, there was little correlation between the factors of safety computed by the two methods. Both predict failure, but FEM shows a different mode of failure plus development of potential failure zones not indicated by conventional methods. Besides having a better theoretical basis than the Bishop method, FEM requires no assumptions regarding the location or geometry of the failure surface. As a result, the program will show progressive development of a failure zone, and areas can be pinpointed where remedial measures should be taken. In addition, nonhomogeneous cross sections can be analyzed, and zones of potential piping can be defined.

Jan 1, 1975

By H. W. Leavenworth

Research was conducted by the Bureau of Mines to develop a technique to grow metallic fibers from a sulfide mineral. In this research, chalcopyrite (CuFeS2) was made sulfur deficient, and the remaining sulfur partitioned to the iron in the mineral to liberate metallic copper, or to the copper to liberate metallic iron. The metals formed on the surface as fibers and in the interior as spherical particles. Fiber growth is very fast. Lengths of 3 to 4 cm form in a matter of minutes, and the diameter of individual fibers is less than 1 µm. The mechanism of fiber growth is explained, and the reactions are reversible as predicted. Copper fibers can be made to grow from the surface at 400° C or to dissolve back onto the solid surface and be replaced by iron fibers at 625° C. Growth and dissolution can also be controlled to form copper/iron duplex fibers.

Jan 1, 1974

By J. J. Shields

This is the Seventh of a series of publications that describe methods and practices used in mining bituminous coal mechanically.3/ This report deals with the operation referred to in coal mining as continuous mining, and the interest shown by mining companies in this method is the reason for this study. Only continuous mining as it applies to the room-and-pillar system of mining, or a modification thereon, is discussed in detail in this report. Although not always as continuous as the name implies, it is a system of mining in which a machine is used to cut and load coal in one continuous operation without drilling and blasting the coal. With the mining equipment in most general use today, the usual cycle of operation in mining of coal is: (1) Timber, (2) cut, (3) drill, (4) blast, and (5) load. As the phases of this type cycle cannot be performed simultaneously in the same working place, it is necessary to operate from 3 to 7 working places so that at least 1 place is available for coal loading at all times. Even if the schedule of the phases in a cycle is maintained, coal production ceases during the time required to move the loading equipment from one loading place to the next. In 1920 a continuous-type mining machine4/ was installed in an Illinois coal mine to drive entries. Several other companies used these entry drivers for short periods in the following few years. In 1927 a southern Illinois coal company installed 2 of these machines which, in the next 25 years, were reported to have driven over 200 miles of entries. The machines did not attain widespread usage.

Jan 1, 1954