Search Documents

By John Campbell, E. S. Baker, G. W. Jones

"INTRODUCTION In previous reports 5,6./ results were given showing the amount of natural ventilation that takes place in manholes (capacities, 74.1 to 308 cubic feet) when the number of ventilation openings in the manhole cover ranged from no openings to a maximum of 4g.The tests warranted the general conclusion that the ventilation or air changes taking place in, a manhole increase as the area of openings in the cover of the manhole is increased, and are proportional (with the exception of a few erratic tests) to the area of the openings in the cover. The area of the openings was the chief factor that affected ventilation.The results did not show any marked change in rate of ventilation due to increased capacity or shape of manhole, when the results were expressed in terms of air changes per day versus area of ventilation openings in square inches per 100 cubic feet of manhole space.It was observed during these investigations that in certain tests that showed erratic results (that is, did not agree with the general average for a given set of test conditions) the wind velocity during the test period was also abnormal. In view of these findings it was decided to conduct a series of tests in which the wind velocity across the openings in the manhole cover could be controlled accurately to determine the effect of wind velocity on ventilation rate."

Aug 1, 1938

By Ralph H. Espach

The value of careful fractionation in the manufacture of petroleum products is recognized more and more by petroleum refiners. Recent studies have shown that the quality of the products depends largely on the type of fractionating equipment and on the care used in operating the equipment. For example Rue3 has shown that careful fractionation of pressure distillate will greatly reduce the amount of chemical treatment necessary to produce finished gasoline. The advantages of the combination of pipe still and bubble tower in obtaining good fractionation are well recognized in the petroleum industry. However, the equipment designed in the past has in general been much too large for convenient laboratory use. The present paper describes a continuous-distillation apparatus for the laboratory study of fractionation. This apparatus has given very satisfactory results in the study of different crude oils and petroleum products. A discussion of the theory and action of bubble towers has not been given, as this subject has been discussed previously by Cooke and Rue4. It is believed that the distillation curves of the products obtained from this apparatus show clearly its capabilities.

Jan 1, 1928

By Gary W. Krantz

Fibered, portland-cement-based gunite products were applied in the Bureau of Mines Lake Lynn Laboratory Experimental Mine using a variety of pneumatic guns and gunning crews, The demonstrated wet-mix (with silica fume), dry-mix, and surface bonding products were sampled by the Bureau and subjected to a suite of engineering analyses. Gunite flexural and compressive strength, rebound, permeability, porosity, dust loading, shooting rate, crew requirements, and cost factors were evaluated. Steel, fiberglass, or polypropylene fibers were contained in all but two of the gunires tested. Both Bureau and private testing laboratory analyses are provided for some products. Electron probe micro-analysis and X-ray diffraction analysis were performed on the silica fume fraction of the wet-mix gunite to characterize the dust. Aggregate size fraction distribution analyses were performed to provide strength relationships. Results indicate that all of the commercially available fibered-gunite materials tested can provide beneficial sealant, spall prevention, or roof stability control attributes for underground mining environments when applied by an experienced crew using a well-maintained gun, in accordance with product manufacturers' recommendations and when used for the designated purpose.

Jan 1, 1984

By David Cooper, Susan Robertson, William Wiehagen, Launa Mallett, Charles Vaught, Joan Dickerson, Richard Conkle, ROBERT PETERS, Mike Brnich, Charles Urban

This trainer’s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators’ manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer’s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee’s knowledge and skills and (2) the trainer’s experience in conducting skills training. The “Skill Check” section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of “teachable moments” where significantly new knowledge and skills can be learned. The videos on the DVD that accompany this guide can be shown at the beginning of training to give trainees an idea of what the job entails and related requirements. They can also be used within the training cycle (after the trainee has some experience in the job) to reinforce key points or as a trigger for eliciting questions about particularly difficult parts of the job. The video segments are meant to be visual models of good performance. They are designed to elicit discussion on good (lower risk) ways to do the job. In this context, they can be used very creatively at different times within the training cycle. The section on “Talking Points” offers a number of questions that can be used in the classroom to support and elaborate on certain aspects of the job duties. If the trainee has a fair amount of underground experience, some of the questions can also be used to support the pretraining assessment (i.e., skill check) of knowledge and skills. Likewise, some of the questions can also be used while teaching on the job to reinforce key points affecting safety, production, or maintenance. The section dealing with a mine’s roof control plan should be used at various times in the training cycle to make sure the trainee understands the plan and knows how to apply it in performing the job. The supplemental materials offer additional resources that can be used to support initial job training or follow-up. Learning continues well after an individual has been trained. The supplemental materials can help reinforce good operating skills and provide an opportunity for further discussion on better ways to do the job.

Jan 8, 2006

By L. Mallett

The changing demographics of the mining industry make successful passing of knowledge and skills to the next generation critical. Training methods and technologies are being developed to meet this need. Twenty years ago classroom training was largely a one-way transfer of knowledge through instructor lectures. In contrast, instructors today can use virtual reality technologies to guide trainees as they fully participate in learning experiences. Trainees can interact with the virtual work environment, co-workers, and equipment without being exposed to workplace hazards. The speed of advancement in mine safety, health, and production training shows no sign of slowing in the next 20 years. Researchers at the National Institute for Occupational Safety and Health have studied and participated in the evolution of miner training. A look at training materials they have created in the past and those they are currently developing reveals changes in methods and technologies over time and also key characteristics which have remained constant. Possibilities for the future can he discussed in the framework of an implementation of virtual reality in new miner training sessions. The example computer-based training package teaches new miners to read mine maps and provides opportunity to practice navigation skills in a virtual mine. With this 'serious game', trainees experience the look and feel of moving through an underground coal mine while in the safety of their classroom. During field-testing in 2007, trainees and instructors responded very favourably to this new way of learning. The software was usable by mine trainers with even limited computer expertise and could be installed on the affordable computers they were using for their more traditional slide presentations. The Underground Coal Mine Map Reading Training's foundation on past successful development strategies and its acceptance by today's instructors and trainees provide valuable lessons for developing training materials, strategies, and technologies for mining's future.

Jan 1, 2009

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By A. C. Fieldner

In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal from the same mine. A letter. in which the following questions were asked was sent to some 50 coke-oven superintendents and others who might be interested; "What is the influence of washing coal on: (1) The chemical and physical properties of coke, as for example, the size the amount of breeze, the fracture, strength, cell-structure, etc. (2) The quantity and quality of gas and by-products. (3) The capacity of the ovens. (4) The composition of the coal. "Your general opinion, as well as any specific data or results of tests, on this important subject will be arc greatly appreciated."

Jan 1, 1930

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By Harry R. Johnson

Laboratory experiments were conducted to study the carbon deposition characteristics of a high-gravity, paraffin-base crude oil. The results of these experiments indicate that a fuel supply adequate to initiate a combustion wave can be deposited in high-gravity-oil reservoirs. These results are significant because there has been considerable doubt whether oils over 35° API gravity are able to deposit sufficient fuel. Considered in these studies were the effects of air flux, temperature, initial oil saturation, and time on carbon deposition. Conditions that maximized carbon deposition in the laboratory and an understanding of the nature of carbon formation are shown by graphical interpretation of the data. Statistical techniques were used to design and analyze the results of the retort tests. For the same amount of laboratory work, this approach yields more information about the systems that were studied than the classical method of research presently used in many laboratories. In addition, the accuracy of calculating the effect of each variable on carbon deposition is twice that of the classical approach. This paper develops the statistical approach to research without complex mathematics, thus enabling the reader to grasp the concept of how statistics can be applied to study many complicated problems.

Jan 1, 1966

By Martin J. Gavin

During the recent study of lubricating oils carried on in the San Francisco laboratory of the United States Bureau of Mines, it became desirable to distill the oils used in the experimental work at pressures as low as 10 millimeters (mercury column) absolute. In the effort to Overcome difficulties and eliminate sources of error, certain changes were made in the apparatus for vacuum distillation used by the Bureau of Mines for crude petroleum.4 These changes were described in R.I. 2819, issued in July, 1927. Subsequent to the publication of R.I. 2819 several other changes have been made, and the present form of the apparatus for vacuum distillation of lubricating oils is described in this revision of R.I. 2819. These changes were found to give more accurate checks on duplicate distillations. The major part of the credit for the laboratory work which developed the changes in the apparatus and method revised herein is due to Boyd Guthrie, assistant petroleum chemist, and R. V. Higgins, junior chemist, o the San Francisco laboratory, United States Bureau of Mines. DESCRIPTION OF APPARATUS The distilling flask employed is essentially the Hempel flask as used by the United States Bureau of Mines for the analytical distillation of petroleum.5 he complete apparatus is shown in Figure 1. The fractionating column and exposed portion of the flask is wrapped with 4 inch asbestos rope and then surrounded by a cylindrical hood of 1/8 inch pliable asbestos sheet with a narrow air space between the wrapping and the cylindrical hood. This was found necessary to prevent any radiation or convection heat losses from the column, and resulted in obtaining a more even and constant fractionation by eliminating any dephlegmating action caused by temperature changes around the column.

Jan 1, 1930

By J. C. Franklin

A 32-channel continuous monitoring system has been developed to monitor radiation working level (WL), fan operation, and air door position. The system consists of a surface receiver unit and an underground transmitter that is connected to the various monitors. A continuous WL monitor used with the system can generate alarms at two different WL readings. One of these levels is variable from 0.00 to 0.99 WL and generates an alarm on the surface receiver. The other level, fixed at 1.0 WL, generates an underground alarm in the vicinity of the monitor. The detectors for fan operation and air door position work on the principle of a completed circuit to the underground transmitter (multiplexer). When the circuit is broken, as is the case when a fan is off or an air door is open, an alarm is generated at the surface receiver. This alarm remains in effect until the circuit is completed, signifying the fan has been turned on or the air door has been closed.

Jan 1, 1982

By W. C. Holliman

This report describes apparatus and procedure used for determining the vapor pressure of aviation gasoline in surveys of commercial aviation-gasoline characteristics made by the Bureau of Mines in cooperation with the Coordinating Fuel and Equipment Committee of the Coordinating Research Council, Inc. (CFR-CRC). The method is a modification of the Reid method, in which a mercury manor is substituted for the Bourdon-type gage of the Reid method. The method was used in earlier surveys made by the National Bureau of Standards in cooperation with the CFR-CRC, and was used in the Bureau of Mines surveys at the request of the cooperating organizations. It is designed for special research problems? particularly in vapor-lock studies, which require a precision greater than obtainable by the Reid vapor pressure method. A repeatability of + 0.01 p.s.i. average deviation from the mean may be obtained by method.

Jan 1, 1950

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By W. C. McBee

A family of modified-sulfur cements has been developed by the Bureau of Mines for the preparation of construction materials with improved properties. Various types of sulfur cements were prepared by reacting sulfur with mixtures of dicyclopentadiene (DCPD) and oligomers of cyclopentadiene (CPD). Durable cements were prepared with structural characteristics ranging from rigid to flexible. These cements were used to prepare corrosion-resistant materials for use in a wide variety of industrial applications where resistance to acidic and salt conditions is needed. These materials were prepared as rigid concretes, flexible pavings, spray coatings, and grouts. Production of modified-sulfur cements in a commercial-size plant was demonstrated.

Jan 1, 1981

Provide the U.S. mining industry with a user friendly computer program to calculate stresses in underground coal mines in order to improve safety conditions for mine workers. Capabilities of MULSIM/NL MULSIM/NL (multiple seams, nonlinear) is a three-dimensional boundary-element method (BEM) program developed at the U.S. Bureau of Mines for stress and displacement analysis of coal mines. It can analyze one or two parallel seams that can have any orientation with respect to the Earth's surface. Three main new features distinguish MULSIM/NL from its predecessors: (1) non¬linear material models, (2) multiple mining steps, and (3) energy release and strain energy computations. MULSIM/NL has six material models for the in-seam material: (1) linear elastic for coal, (2) strain softening, (3) elastic plastic, (4) bilinear hardening, (5) strain hardening, and (6) linear elastic for gob. The multiple mining step capability enables the user to efficiently simulate a changing mine geometry. Finally, MULSIM/ NL computes energy release rate due to mining using the most recent concepts advanced by Salamon.

Jan 1, 1993

By Carl Belser

In 1925 the Park Utah Consolidated Mines Co., after several years of experimental work, installed a system for signalling from cages which has been operating efficiently and with low upkeep costs for the post 19 years. The system was adopted for a large western metal mine but was later abandoned be arse of the constantly shifting shaft alinement. Recently the system has been studied and probably will be put into service at two other large mines. One of the principal reasons wry the system has not boon adopted more widely has been the lack of adequate details both as to the desirability of having such a system and as to its construction and operation. Previous signaling, systems contained undesirable features, such as charged bare wires extending the full length of the shaft. Under the direction of O. N. Friendly, then general superintendent of the Judge Mining & Smelting Co., the present system, entailing the use of a samll current at low voltage, was gradually developed. Many of the refinements in the system wore contributed by Leonard Wilson, consulting electrical engineer, Salt Lake City, Utah.

Jan 1, 1945

By Robert W. Freedman

Vacutainers are used by the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) for sampling mine air and products of combustion. Tests were conducted on both 10-ml and 30-ml sizes to study shelf life stability during storage, pretreatment of stoppers, and handling of a wider range of compounds. A chamber was constructed to provide convenient, efficient evacuation of the Vacutainers shortly prior to use. Fixed gases and C1 ?C5 hydrocarbons could be stored for 1 week or more after sampling. Where decreases occurred (C02 and C3-C5 hydrocarbons), they were predictable as a function of storage time. An unexplained phenomenon, slow accumulation of CO in evacuated Vacutainers, occurred after a few weeks of storage. The levels were low and time dependent. Attempts to eliminate this behavior by pretreating the stoppers were unsuccessful.

Jan 1, 1976

By S. A. Gustavson, H. E. Olund

This report has been prepared to review the history of the Premium Price Plan for copper, lead, and zinc, which was in operation from February 1, 1942, to June 30, 1947. It includes various charts and tables comparing costs and production data, and data on exploration premiums that were included in the Plan during the last year of its operation.

Jan 1, 1950

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932