Search Documents

By R. C. Buehl

An experimental iron blast furnace of 3-foot-diameter hearth, producing about 12 tons of metal per day, was operated for 2 weeks with various proportions of anthracite replacing a corresponding amount of coke. The furnace operated well with anthracite in amounts up to 40 percent of the total fuel and produced metal of uniformly low sulfur and normal silicon contents. An increase to 50 percent anthracite during two attempts resulted in poor operation and the charge hung in the s haft of the furnace. INTRODUCTION Anthracite production in Pennsylvania decreased from 84,400,000 net tons in 1926 to 40,600,000 net tons in 1952, and there was a further decline in 1953 to 30,900,000 net tons. Employment in the anthracite industry dropped from 165,000 men working an average of 244 days per year in 1926 to 57,900 working an average of 163 days per year in 1953,3/ which has naturally resulted in considerable unemployment in the region. The industry is actively engaged in promoting new uses for anthracite to increase the demand and thus improve economic conditions in the region. One possibility is the use of anthracite to replace part of the coke for smelting iron ore in blast furnaces. The tests in this report were made to determine whether this use of anthracite would be feasible.

Jan 1, 1955

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart, More detail regarding the use of the chart is included than was given in the earlier version.

Jan 1, 1967

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Uruguay has been prepared from the best available information in Washington, but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State .

Sep 1, 1930

By Wm. W. Odell

For a number of years there has been a very appreciable annual,, increase in the production and recovery of natural gas and natural-gas gasoline2 in the United States the latter product being used largely for blending with gasoline from petroleum in the production of motor fuel. On account of the increased amount of oil cracking in the production of gasoline and the accompanying increased percentage of low-boiling constituents in the resulting product, the specifications for the natural gasoline suitable for blending have been altered, that is, the amounts of propane and butane which it can contain have been limited. The result has been that large quantities of the latter materials are wasted because there has been no ready market for thorn in large quantities. Because of this wasteage and because it is probable that large quantities of there and similar materials will be produced in the near future us a result of the more general use of oil cracking processes, a study was made by the Bureau of Mines, under a cooperative agreement with the assistance of the Phillips Petroleum Company, of the suitability of these materials alone or in mixtures for use as gas enricher in the carburetion of water gas for city distribution. This investigation included: (a) A study of the properties of the low boiling members of the paraffin series including pentane with particular reference to their utilization as gases.

Jan 1, 1927

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK - ALTIMETER SURVEY WITHOUT ALTMETER TEMPERATURE CORRECTION 1 BAS 8: 22 1391 1391 53. 49.

Jan 1, 1977

Improve safety at mineral operations that use cyanide leach solutions to recover precious metals from finely ground ores, Approach Provide an alternative, non-acidic means of cleaning processing systems such as the State-of-Maine filter system, thereby reducing the exposure of workers to toxic hydrogen cyanide gas (HCN), The Problem Many gold and silver mining operations use cyanide solutions to dissolve gold and silver from ores. The precious metals frequently are recovered from pregnant leach solutions by the Merrill-Crowe recovery process, whereby gold and silver is precipitated with zinc dust. When that method is used, suspended particles in the leach solution must be filtered out before zinc precipitation can occur. This filtering is accomplished with small packaged plants, such as the State-of-Maine (SOM) filtering system. Unfortunately, the filters become clogged with calcium carbonate scale after about 2 to 10 days of operation and must be cleaned before further precious metals recovery operations can continue, Cleaning the system is a hazardous task because the acid is not compatible with the alkaline cyanide leach solutions, and toxic hydrogen cyanide (HCN) gas may be produced when the acid and solution are mixed. That gas, if breathed or contacted with the skin, can cause cyanosis which may induce nausea and even asphyxia and death. To reduce this danger, the Bureau of Mines has devised a safer method of cleaning clogged filters,

Jan 1, 1986

By J. B. Gayle

The rate of oxidation of coals with nitric acid has been used by earlier investigators4 5 6/ for determining fusain and for studying petrographic composition. These workers accumulated considerable evidence indicating that, for coals ranging from lignite to low-volatile in rank, the method gives values for fusain that agree satisfactorily with those obtained by optical methods. One group5/even concluded that, when discrepancies are noted between results obtained by chemical and microscopic methods, the results based on the oxidation reaction are probably the more reliable. Unfortunately, after concluding that the method was valid, most of these workers apparently lost interest. As a result, no attempt to exploit or apply the method to problems of utilization has been reported. Recent studies of the influence of inert petrographic constituents on the properties of cokes made from various coals7/ have indicated a need for additional means of characterizing coals and blends used for carbonization.

Jan 1, 1960

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950

By R. V. Ramani, A. S. C. Owili-eger

A mass balance equation can be written for the unit block of Figure 7 for changes within the volume during time At as: [ ] where x and y are the coordinates; q is the flow across any surface; p is the density of the fluid flowing through the medium; qvol is the volumetric flowrate; @ is the medium porosity; and Ax and Ay are the dimensions of the block. The subscripts t and (t+At) denote time levels and At is the change in time. Writing this equation in nota- tional form and on rearranging, the following expression is obtained:

Jan 1, 1974

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By Larry Patts, Michael J. Brnich

Approximately 45% of U.S. coal is produced from underground mining. The use of diesel engines to power under- ground mining equipment has steadily increased over the past four decades in an effort to improve mine safety and productivity. Several advantages realized with the use of diesel-powered mining equipment in underground coal mines are listed in Table I. The primary disadvantage of using diesel equipment in underground coal mines is that diesel exhaust emissions can contaminate mine ventilation air. The major constituents of diesel exhaust are gaseous emissions (which include carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons) and diesel particulate matter (DPM). The Mine Safety and Health Administration (MSHA) has incorporated threshold limit values for all gaseous components of diesel exhaust into their regulations. These have been established by the American Conference of Governmental Industrial Hygienists.

By D. W. Richardson

This Bureau of Mines publication provides the enthalpy of formation of malachite [Cua(COs)(OH)2] as determined by hydrochloric acid solution calorimetry. At 298.15 K the enthalpy of formation from the component oxides is -15.l0±0.30 kcal/mole and from the elements, -251.9±0.5 kcal/mole.

Jan 1, 1974

By R. V. Lundquist

The Bureau of Mines made a laboratory study of the amenability of anorthosite rock ( from the San Gabriel Mountains , Los Angeles County , Calif . ) to treatment by the lime soda sinter process for the extraction of alumina . The study was done under a cooperative agreement with the California Division of Mines and Geology . This report presents the results of the investigation , and it includes a review of the geology of the deposit ( 7 ) by Dr. Gordon B. Oakeshott . Interest in the recovery of alumina from submarginal aluminum silicate ores is stimulated by the fact that the domestic aluminum industry depends on imports of bauxite for its alumina requirements . Of the 8.0 million long dry tons of high - grade bauxite consumed in 1961 for producing metallurgicalgrade alumina , only 0.9 million long tons , or 11 percent , was mined in this country . During past years many organizations have carried out research programs to determine if alumina could be extracted economically from such domestic ores as clays ( 3 , 4 ) , anorthosite ( 8 ) , and other silicate sources . Successful alumina extraction is the ultimate objective of the Bureau of Mines program.

Jan 1, 1963

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By F. E. Cash

The Holmes Safety Association , organized and named in honor of the late Dr. Joseph A. Holmes , first director of the United States Bureau of Mines , has for its object the prevention cf accidents , the improvement of health conditions at work, in the home , and in public places , and the promotion of the general welfare of its members . As a means of preventing accidents and advancing health and safety , the Holmes Safety Association disseminates information , gives instructions on subjects related to safety , and promotes first -aid and other forms of protective and accident - prevention training . This organization is intended to work and cooperate in the closest possible way with existing mine or plant safety organizations in conducting educational , social , and recreational activities for the promotion of health , safety , and efficiency .

Jan 1, 1929

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955