Search Documents

Research workers From the Bureau of Mines and industry met with other government and industry representatives in Pittsburgh, Pa., on January 22, 1975, to discuss the results of research under the Bureau of Mines Noise Control Program. The program, aimed at reducing noise in mines, is functionally divided into three major areas: Instrumentation, personal protection, and noise abatement. This proceedings contains the opening remarks to the seminar and seven technical presentations based on various aspects of noise abatement and control.

Jan 1, 1975

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

This publication summarizes the research (in-house and contract projects) programmed by the Bureau of Mines for fiscal year 1984 (October 1, 1983-September 30, 1984) under its Health and Safety Technology Program. The objective of these projects is to provide an ordered and sequenced advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1983

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

By Edward P. Barrett

The production of sponge iron is one of the earliest arts in the metal¬lurgy of iron and steel. The idea of producing iron direct from ore at temperatures lower than the melting point of, the iron has persisted throughout the centuries. The purpose of this paper is to present a general picture of the methods, proposed or tried within the past 100 years, for producing sponge iron by treating hot ore with heated reducing gases. The abundant literature has been abstracted, and quoted freely. Publications concerning more detailed information on the various methods are referred to in the footnotes and in the bibliography.

Jan 1, 1949

By Oliver Bowles

Since 1922 when the Bureau of Mines issued a report2 covering the slate industry in detail, changes in technology have taken place which have an important bearing on the industry. The present paper comprises a record of these changes. Though the value of slate, for roofing, structural, blackboard, sanitary, and electrical uses is generally recognized, it has many competitors. To meet this constantly increasing competition producers are promoting economies in manufacture, and improving processes, thereby lessening costs of production, and are placing on the market products of the highest possible quality, thus creating satisfaction and confidence on the part of the user. This endeavor to place the industry on a better basis, both as regards processes and products, is shown in the recent developments in technology which are presented herein. Valuable assistance in obtaining data for this paper was given by W. S. Hays, secretary of the National Slate Association, N. M. Male, president of the National Slate Association, and Robert Notvest, consulting engineer, Cleveland, O.

Jan 1, 1926

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By D. R. Tesarik

As part of its research program to investigate ways of improving resource recovery and reducing subsidence, researchers from the U.S. Bureau of Mines placed instruments in the B-North ore body of the Cannon Mine, Wenatchee, WA, to monitor cemented backfill and rock deformation during mining. The vibrating-wire gauges proved to be reliable and versatile, and approximately half of the instruments are providing data after 2 years of use. A two-dimensional, finite-element model was used to analyze the Cannon Mine's multilevel bench cut-and-fill mining method and predict rock and backfill displacements. The model accurately predicted rock displacements, but the predicted and measured displacements in cemented backfill had a correlation coefficient near zero, indicating that the model should only be used to predict rock displacements and not backfill displacements. A finite-difference model was also used to evaluate the stability of a cemented backfill pillar. Results can be used to conservatively predict backfill stresses, but on-site observation of pillar failures coupled with in situ measurements are needed to make more accurate predictions. An ongoing evaluation of the mining system has indicated that filling the primary stopes tight to the back with cemented backfill allowed these pillars to carry overburden loads soon after the cemented backfill was placed.

Jan 1, 2010

By W. D. Ryan

Industry must be made to realize that "Safety First" means just that - safety first. The miner must realize that safety first takes precedence over earnings. The employer must realize that safety is the first consideration, and is not to be subordinated to profit-making. Neither employee nor employer is justified in adopting the principle of safety first with reservations; that is they will practice safety first only so long as they think that it does not interfere with earnings or profits. This paper proposes to demonstrate that suberdinating safety to possible profit is short-sighted and that over an ex- tended period of time it dres not result in increased profits or earnings. An employee through disregard of safe practice may receive an injury that will cause him a loss of earnings if, indeed, he is net killed or permanently in- capacitated. If permanently incapacitated any compensation he may receive is very likely to be wholly inadequate as compared with probable earnings if the accident had not cccurred. The employer, upon his part, will find that the burden of compensating his injured employse will far exceed the outlay of money necessary to maintain a reasonable program of safety in his mine or plant. The mine foreman is one of the most important factors in the matter of mine safety. A vigilant and competent mine foreman, once he has established the confidence of the employees in his ability as a foreman, can be of invalu- able assistance in promoting mine safety, for through him and his assistants the employees may be made to cooperate. Every employer should remember, then, that the soluction of the foremen and their assistants is one of the most important matters connected with the work of establishing the maximum amount of safety in his mine. Everyone connected with the mining industry must be made to realize that there is to be no back-sliding and no let-up in safety work; that no matter how dry and tedious the routine may seem it is absolutely essential and justi- fied for both humanitarian and economical reasons. Efficient safety effort pays dividends in actual cash to both employer and employee. About 50 per cent of underground accidents in coal mines take place at the working face where the miners dig and load the coal. Approximately 17 per cent of coal-mine fatal accidents are the result of underground haulage. Face and haulage accidents can and will be reduced materially if the individual miner takes all precautions necessary to protect himself and if the management

Jun 1, 1930

By Alexander May

This report describes a new method of weighing based upon observing the apparent weight of an object ill two separate pure gases. The method is presented in terms of experimental data which prove its soundness, but does not attempt to show the maximum accuracy possible with this technique. The new method incorporates the underlying principle that the apparent weight of an object is a linear function of the density of the atmosphere in which the object is weighed. The coefficients of this linear function are the true mass and volume of the object. From this functional relationship the true mass and volume of the object may be determined.

Jan 1, 1970

By E. W. Felegy

Since 1920, the Bureau of Mines and, other agencies have conducted numerous investigations of methods of communication for use in mines in times of disaster or emergency. The results of these investigations have been reported in various publications (3, 4; 5, 6, 8, 9, 10, 11, 12, 13, 14, 15, 16). In November 1944, the Bureau of Mines resumed the study of emergency underground communications. Until March 1946, the program was directed toward reexamining methods of underground communication that indicated possibilities of success. Since April 1946, the principal interest of this investigation has been in methods of application of radio to communication in mines, low-frequency radio seeming to offer the most promise as a successful method of emergency mine communication. Results achieved in reexamining other methods and in the investigation or the application of low-frequency radio between November 1944 and September 1946 were reported previously in a publication entitled "Some Studies on Emergency Mine Communications".

Jan 1, 1948

By L. J. Prosser

The Bureau of Mines has completed an underground degasification project in which an underground piping system was used to transport methane from the coalbed to the surface. In a la-month period four horizontal holes were drilled to an average depth of 1,450 feet. All four holes were surveyed vertically and azimuthally. In 991 days of degasification, 255 MMcf of gas was drained from the coalbed. The underground piping system proved to be a safe and effective means of transporting methane from the coalbed to the surface.

Jan 1, 1981

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By Sara Jane Boles

The purpose of this Bureau of Mines investigation was primarily to isolate and examine the effect of liquid content upon the apparent porosity and bulk density of compacts pressed from high-purity, fused aluminum oxide, and, secondarily, to study the actual mechanism by which the liquid content affects the bulk density. No attempt was made to approach the theoretical maximum density of the oxide by introducing additives, particle packings, or similar variables; instead this study is an intercomparison of the bulk densities obtained as functions of the water contents of the compacting mixtures. Water content was varied from 7 percent to 25 percent, on a total-weight basis. The data gathered indicated a well-defined optimum water content for obtaining minimum apparent porosity and maximum bulk density, under the conditions of the experiment. During the course of this study, a number of additional variables in the forming process were discovered and are introduced in this report, although a thorough evaluation was found to be beyond the scope of this present investigation.

Jan 1, 1963

By R. V. Higgins

Tarner (1),3/ Muskat (2), and Schilthuis (1) have presented methods of calculating oil recovery by the expansion of dissolved gas with and without return of gas to the reservoir. Although electronic computers have eliminated the tedious and time-consuming calculations (4) required by each of these methods, many petroleum engineers do not have access to electronic computers. For these engineers a short method is presented that uses the Tarner method as a base. Moreover, for engineers who have access to computers and have not as yet prepared a program, the short Tamer method requires less computer time than the long iterative methods. In the proposed short method, no plotting of the calculated data is required to determine a point of intersection described in the original Tarner presentation, as only one calculation is needed to determine the value sought, or two calculations if greater accuracy is desired.

Jan 1, 1960

By A. A. Berk

The Bureau of Mines devised a test nipple for the field study of corrosion in the condensate-return lines of Federal heating plants. Corrosion surveys, made with this device, showed that the deterioration of the piping was caused principally by carbonic acid in the steam condensate. Corrosion problems were brought under control when the carbonic acid concentration in the condensate was decreased. In many instances, this was effected by decreasing the total carbon dioxide content of the feedwater; in others, the condensate acidity was neutralized with volatile, alkaline chemicals. Filming treatment with octadecylamine, reported successful in controlling return-line corrosion in industry, was much less effective in Federal area-heating plants. Laboratory study by the Bureau disclosed that octadecylamine is unstable in heating systems. Analytical methods were developed for this chemical and its degradation products in heating-plant condensate. Field surveys, in using these methods, confirmed the instability of the filming material. Laboratory tests showed that the degradation products are not useful film formers. Since filming treatment has little effect on condensate corrosivity, the piping was corroded where it was not coated by the treatment chemical.

Jan 1, 1962

By J. B. Zadra, J. M. Gomes, Don H. Baker

Electrolytic deposition at 1,000 ° C in an electrolyte essentially consisting of 7 parts sodium pyrophosphate , 2 parts sodium chloride , and 1 part sodium tetraborate yielded tungsten of 99.9 percent purity . Scheelite concentrates containing 25 to 73 percent WO, and varying quantities of iron , lime , and silica were used as feed materials for the electrolysis . The metal contained less than 0.01 weight - percent each of iron , calcium , silicon , aluminum , carbon , and oxygen . Modification of the electrolyte permitted deposition of equal - quality metal from scheelite concentrates containing higher quantities of iron , calcium , and silica . The electrolytic separation of molybdenum and tungsten was accomplished by minor variations in the operating procedures .

Jan 1, 1964

By R. O. Kneisley

This U.S. Bureau of Mines report summarizes a study of large-scale strata response to longwall mining at a western U.S. coal mine. This study utilized surface and subsurface measurements, geologic mapping, in situ stress measurements, and pressure cell readings to characterize strata behavior. Preliminary analysis of surface subsidence and time-domain reflectometry (TDR) was used to determine a suggested main roof caving sequence. Coal ejected from the face apparently resulted from brittle failures that occurred because of lack of significant yield zone development. The combination of a strong coal with pronounced directional behavior, low overburden pressures, a good caving roof, and a high-production environment that minimized time-dependent loading apparently reduced yielding of the longwall face. The panel 1 headgate-entry design appears adequate; however, the abutment pillar and adjacent panel tailgate rib are highly stressed and may contribute to problems during second panel mining. The small chain pillar yielded after passage of the face, but the pillar width may be near maximum since evidence of a stressed core exists.

Jan 1, 2010

Objective: To discourage miners from going inby unsupported mine roof by developing intrinsically safe devices that render the attendant hazard more evident, direct a person's attention to read the warning message on the module, and thus avoid the hazard beyond the device.

May 1, 1997