Search Documents

By R. A. Busch, R. R. Backer, R. W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slur- ry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton sample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol- ids). The resultant friction-pressure gradients ranged from 0.06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposi- tion tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, ad- ditional water was released; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitabil- ity for use as backfill material in active mines.

Jan 1, 1965

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By A. Wahab Khair

"This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally confined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable ·for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage. INTRODUCTIONOne of the relevant processes in the coal cutting technology is the application of indentation theories. Since most cutting tools in the coal industry are wedge shaped most of the indentation research is found for a wedge shaped tool.A wide range of behavior is found in different rocks subjected to the wedge penetration. A rock which is elastic brittle at standard pressure might become elastic plastic at high confining pressure (Gnirk and Cheatham, 1963). It was also observed that some rocks will merely be crushed and indented by a wedge whereas others will crack and form chips, furthermore the existence or non-existence of chips depends mostly on the geometry of the indenter, type of rock and the depth of penetration (Evans and Murrel, 1958). However, coal cutting technology is mostly explained by models which use rigid wedge to penetrate into a brittle material in which both crushing and chipping will occur (Evans and Murrel, 1958, 1962)."

Jan 1, 1988

By R. A. Beall, W. E. Anable

The purification of hafnium by electron- beam melting at moderate energy inputs and at low pressures was examined in detail . Most metallic impurities and hydrogen were removed in the first few minutes of operation ; oxygen , carbon , and nitrogen were removed at a slower rate . Samples treated by electron bombardment suffered a small loss of weight and a gradual lowering of hardness . The magnitude of each change varied with the energy input and the duration of the melt . Analysis of the data confirms the loss of oxygen as a hafnium monoxide . Approximate activity coefficients for other contaminants are given .

Jan 1, 1964

By A. M. Evans, J. H. Soulé

"INTRODUCTION Deposits of iron ore in Cherokee County, Tex., have been worked at various times in the pact, and the ore has been smelted in small local blast furnaces.Recently it was proposed to establish a charcoal blast furnace with a wood distillation plant to produce charcoal for fuel and byproducts. Financial assistance from the Reconstruction Finance Corporation was sought by George Easley and associates to enable them to purchase, move, and erect the furnace and build the required accessory plants. The furnace was to be moved from Pembroke, Fla.In August 1941, the Bureau of Mines was asked by the Office of Production Management to check the development work of Easley and associates and to ascertain (1) the iron-ore reserves, (2) the cost of mining ore and delivering it to the blast furnace, and (3) the grade and character of the ore. The Bureau of Mines was advised, while the investigation was in progress, that approximately 1,000,000 long tons of measured reserves would be sufficient to demonstrate the feasibility of operating the properties.Although deposits of iron ore are widely distributed in Cherokee County, only the Pryor Mountain, Banks and Cherokee, J. P. Acker, and Citizens State Bank tracts were sampled thoroughly by the Bureau of Mines. The iron-ore rights on these are owned by the New Birmingham Development Co., the Cherokee Development Co., or by individuals. Options to lease the ore rights were obtained by Easley, who obtained options on the Hawes Peach Orchard and Bradford tracts, also, which were examined only cursorily by the Bureau."

Aug 1, 1947

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By E. L. Singleton

The electrochemical reduction of aluminum chloride to aluminum was investigated in a closed, two-compartment cell utilizing a molten chloride electrolyte. The externally heated cell was divided into a reduction compartment and a combination AICl3 feed and metal removal compartment. Aluminum was deposited at 700° C on a molten aluminum catbode from a KCI-NaCI-AICI3 electrolyte. The AICl3 content of the electrolyte was replenished by either vapor or solid additions. The chlorine evolved was collected and measured to give a quantitative evaluation of AICl3 reduction. The effects of anode and cathode current densities and AIC13 concentration on anode current efficiencies were studiedo A range of 64 to 84 percent anode current efficiency was obtained with the 25-pound electrolyte capacity cell and related auxiliary equipment.

Jan 1, 1968

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspars as substitutes for natural fluorspar in basic oxygen steelmaking using a high-temperature rotational viscometer and a quarter-ton basic oxygen furnace (BOF). Consider-able variation in stability and BOF slag fluidizing properties were found when using the initial synthetic products, but improved synthesis methods produced synthetic fluorspars that were generally comparable to natural fluorspar in laboratory testing. Trials in the furnace showed the synthetic products to be operationally the equivalent of natural fluorspar. Higher sulfur and phosphorus contents in some of the synthetic materials did not adversely affect the steel chemistry. Analyses of wet scrubber samples showed evidence that the pelletized synthetic fluorspars experienced greater physical and chemical disintegration than did natural fluorspar. It was also found that operation of a BOF without fluorspar is possible when making low-carbon steels because iron oxide is intrinsically generated as the slag fluidizer.

Jan 1, 1981

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By G. E. McElroy

This report discusses the construction and use of an all-pressure psychrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air-conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines - throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the atmosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heating and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure - 29.92 inches mercury.

Dec 1, 1947

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By Frank C. Morris

It is generally recognized that the productivity and ultimate recovery of an oil well may be reduced as a result of reduction in permeability of the sand at the well bore by invasion of filtrates and clay particles from drilling fluids. As a means of determining whether a sand has been "damaged" from these sources, several investigators2 3 4 5/ have developed methods of analysis based on the rate of increase in bottom-hole pressure while a well is shut in. Because of growing recognition of the importance of completion practices as related to the quantity of oil that may be recovered from wells, the Bureau of Mines has studied completion practices in California and the Midcontinent area. Well-interference and pressure-buildup tests were completed Ear seven wells in the Scurry Reef field to determine the effective permeability in the reservoir.6/ Also, a study was made of the pressure-decline curves obtained from 35 water-input wells in 5 different production areas of northeastern Oklahoma and eastern Kansas.7/

Jan 1, 1957