Search Documents

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, Nest Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By Ivette E. Torres

Of the 15 selected non fuel mineral commodities detailed in table 12, only 3 indicated increases in worldwide consumption in 1992. As in 1991, decline in consumption levels of the selected commodities can be attributed to reduced levels of use in the former U.S.S.R. and Eastern Europe. Of the remaining 12 commodities, 2 magnesium and cadmium, stayed relatively the same, while the other 10, including iron and steel, all recorded decreases. Global consumption of iron ore is estimated to have fallen about 3.5 % or about 30 million tons. This is a greater decline than what was estimated for production of iron ore, which is down only 2.7% or nearly 26.5 million tons, suggesting an addition to stocks. The consumption trend for iron and steel has been declining since 1989. This has mainly been due to the continued drops in use in the former U.S.S.R. and Eastern Europe. Even as the European economy begins to turn upward, there may only be a slight increase in consumption of iron, steel, and cement, considering the high cost of construction needed to modernize factories and buildings in Eastern Europe. Many feel that the economies of these countries are limited by the current status of their industries.

Jan 1, 1994

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By D. A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. H0122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available.

By Claude A. Tongish

This Federal Bureau of Mines report presents information on the accumulation and distribution of helium in U.S. natural gas reservoirs. The investigation concerns the relationship or association of helium with geographic location, geologic age, reservoir depth, nitrogen, carbon dioxide, and argon. Although helium is a minor constituent in natural gas, these data show that certain conditions make some reservoirs statistically more favorable than others for the accumulation of helium. The report is based on gas analysis information collected-by the Bureau from 1917 to 1974 from 10,086 gas samples, representing 6,455 reservoirs in 35 States. The occurrence of helium in the reservoirs was 11.5 percent with less than 0.005 percent of helium, 70.9 percent with 0.005 through 0.29 per-cent of helium, and 17.6 percent with 0.30 percent or more of helium in the gas. Results of the various correlations are presented in tables and charts. Relationships have also been determined quantitatively by measures of correlation. The statistical data can be used to determine the environment under which reservoirs with high-helium contents are most likely to occur. These data can be used with other information for predicting the future helium resources of the United States.

Jan 1, 1980

By M. E. Tyrrell

The Bureau of Mines produced building brick of good quality in an investigation designed to explore the possible utilization of high-glass fractions of municipal incinerator residues in the manufacture of building products. Common clays, lime, and sodium silicate were used as binders for the nonplastic residues Test bricks were formed by dry-pressing, soft-mud molding, and stiff-mud extrusion. A run of standard-size face brick dry-pressed and fired in the West Virginia University Coal Research Bureau pilot plant demonstrated that SW-grade glass-clay face brick can be produced on a commercial scale without difficulty. A cost evaluation made for production of the brick showed an estimated cost of $42.13 per thousand bricks for a shuttle kiln plant and $28.70 per thousand for a tunnel kiln plant.

Jan 1, 1972

By B. R. Mohal, S. Chander

"The adsorption and wetting behavior of freshly ground and aged coals has been determined in the presence of a nonionic surfactant. The amount of surfactant adsorption changes with the concentration and ""age"" of the coal. The freshly ground coal has smaller amounts of adsorption at lower surfactant concentrations than the ""aged"" coal whereas at large surfactant concentrations, the order is reversed . In the latter case, more surfactant is adsorbed on fresh coal than on the ""aged"" coal . . It is proposed that at low concentrations, the surfactant adsorbs through both hydrophobic and hydrophilic interactions with the molecule lying parallel to the· surface, whereas at higher concentrations surface micelles form at the hydrophobic sites. The wetting behavior correlates well with the adsorption behavior.INTRODUCTIONNonionic surfactants have many applications in the coal and mineral processing industry. They can be used as dispersing agents to modulate flotation, flocculation and filtration of particulates (1). They can also be used to increase the wettability of hydrophobic solids such as coal and can hence be used as dust suppressants (2,3). Although the adsorption of representative nonionic surfactants such as Triton N-101 (an ethoxylated nonylphenol with 9.5 moles of ~thylene oxide and HLB equal to 13.4) have been studied extensively on substrates such as calcium carbonate (4), silica (5) carbon black (6) and graphite (7), very few studies are available for coals. Coals differ from other substrates with respect to two important characteristics: 1) coal are porous and 2) coals consist of a patchwork of hydrophobic and hydrophilic sites (8). Since the adsorption characteristics of a surfactant are influenced significantly by the nature of the substrate the characteristics of the coals must be taken into consideration."

Jan 1, 1989

By Oliver Bowles

"Properties and Uses.Iceland spar is a name given to a pure crystallized form of calcite (CaCo3) which is sufficiently transparent and free of defects to be used in the manufacture of optical instruments. While the actual requirements are small, the degree of purity and physical perfection demanded renders it somewhat difficult to obtain suitable material.The properties of value in Iceland spar are its transparency combined with double refraction. It is used in the manufacture of polarizing microscopes, saccharimeters, colorimeters and photometers. Its most important use is in the manufacture of Nicol prisms, which constitute an essential part of every polarizing microscope. The principle governing the construction of the Nicol prism is as follows:Ordinary light in passing through a crystal of calcite is resolved into two rays of plane polarized light vibrating in planes at right angles to each other and having different indices of refraction. Thus the two rays follow different paths through the crystal. The prism of Iceland spar is cut diagonally and cemented together again with a transparent cement having an index of refraction intermediate between the two rays passing through the prism. Canada balsam is employed for this purpose. The prism is cut at such an angle that the ray having the greatest index of refraction meets the surface of the balsam at an angle greater than the angle of total reflection, and it is thus deflected to the side of the prism, while the second ray passes through. Thus one of the rays is eliminated and polarized light vibrating in a single plane is obtained."

Apr 1, 1920

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

By L. B. Pankratz

Thermodynamic data on the elements, oxides, sulfides, halides, and selected hydrides, carbides, nitrides, carbonates, sulfates, silicates, and miscellaneous compounds were reviewed, evaluated, and compiled at the Bureau of Mines. Values for CP°, S°, H° -H°298, ?Hf°, and ?Gf° are given in tabular form. A brief thermodynamic background and a number of examples and applications are presented.

Jan 1, 1984

By W. E. Miller, G. S. Scott, G. W. Jones

"An important activity of the Bureau of Mines is the promotion of safety in mining and industry. In connection with these activities, the Bureau determines the explosion hazards of combustible gases, liquids, and solids and investigates means by which explosions may be eliminated or reduced in violence.The limits of inflammability and ignition temperature of combustible gases, vapors, and solids are of practical importance because such materials can be manufactured, transported, and used with greater safety, provided the range of concentrations and temperatures that cause explosions are known.Many organic compounds, which until a few year ago were merely laboratory curiosities, are now being manufactured in large quantities owing to the national emergency, particularly those chemicals entering into the manufacture of synthetic rubber, a product that is playing a major role in the Government program of national defense. This re Jolt gives results relative to the limits of inflammability of styrene and its ignition temperature in air and oxygen. This combustible liquid is now used extensively in the manufacture of synthetic rubber."

Mar 1, 1942

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By W. Hermanson

This report presents the results of a task to complete a final design of a remote controlled hi-roof bolting machine for high roof areas in coal mines. The project was begun by visiting several coal mines to become familiar with roof fall areas. Several machine concepts were generated and presented to the design committee for criticism. A preliminary design was completed, as covered by this report. A Final Design and Final Report will be issued incorporating the committee comments at the Preliminary Design review and comments received concerning this Preliminary Design Report.

Jan 1, 1979

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

By M. J. Sheridan

"INTRODUCTION In December 1942, the-Bureau of Mines reported favorably on a proposal to grant Government assistance-in constructing an access road (consisting principally of a timber-pile bridge across the Rio Grande at Hot Springs, N. Mex.) to the property under lease to the United States Fluorspar Co. At that time the property was being developed actively, and there appeared to be no immediate-need for exploratory or metallurgical assistance by the Bureau of Mines.Because milling facilities were inadequate; the access-read project was eventually disapproved, but prior to disapproval the company had discontinued operations. In June 1943, exploration was resumed by the Humphreys Gold Corporation of Denver, which had subleased the property. Difficulty of access continued to interfere with exploratory progress. In July 1945, at the request of the lessee, the Bureau of Mines directed sampling, using company employees.At the completion of this sampling program, the Bureau of Mines concluded that the property was potentially a important source of fluorite but that further development for production appeared to depend largely on the establishment, by exploration, of adequate reserves. Because of the relatively easy position-of metallurgical-grade concentrate and ores, it also was deemed advisable to investigate the possibility of producing acid-grade concentrate from the ore, for which a demand was becoming evident. Accordingly, a program of trenching, diamond drilling, and metallurgical testing was undertaken by the Bureau. The results of its investigation are reported herein."

Feb 1, 1947

This report describes the development, installation and performance of a lonpwall illumination system. The longwall illumination system was installed at the Greenwich Collieries 112, Cockport, Pa. It utilized flourescent luminaires, intrinsically safe power distribution and is the first longwall system installed in Pennsylvania.

Jan 1, 1976

By Roy L. Soderberg

Ground support for metal, nonmetal, and coal mines was examined through fill placement with a pneumatic stower to increase extraction, reduce ground pressures, and improve general mine safety. Several pneumatically stowed stope-fill products were tested to determine the effects of specific gravity, gradation, moisture, and impact velocity on the in-place density of the stowed fill. Hydraulic sand filling has now served the mining industry for several decades but because of the low density does not always provide ample support to the hanging wall; therefore, the sill and crown pillars sometimes build up excessive stresses that are detrimental to mining. Cementation of a dense fill adjacent to a pillar to allow 100-pct extraction of the pillar, or a fill that can be placed without the use of water and where water is a detriment to rubber-tired mining equipment, was found to be a possible use of pneumatic fill. Placing of coal mine washery products into abandoned underground workings is another possibility in order to completely eliminate surface impoundments.

Jan 1, 1976

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in develop¬ment of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978