Search Documents

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By Oliver C. Ralston

[The NOJ'l..metals Division deals wi tt mi:leral n t inte .ded to be used a ra\o,f materials for extraction of metals. ~ _ ereas, a. materinl containing a chromite, if used' for production of c~1r()rrti1..1r.'l ::tetE' .. l or fcrrochromiu"1, 1,oJould be a chromi te ore, if used as 8. rcfrn.cto~J or for prod .1.ction of chromium chemicals, it is a chromi te-beari [. ~?oCl... Li;{eHise, a r:1a&neti te used for production of iron is a metallifero"'..ls ~in8re..i; if used 8.S a water-filtration granule in .:l magne.tically cleaned filter bed, it 'ould be a nonmetallic in-dustrial mineral.]

Jan 1, 1940

By Zsuzsanna Zborovszky

Study of different parameters (minimum discharge voltage, minimum discharge current, wire electrode diameter, speed of separation, electrode materials, overlap of the electrodes, etc.), their direct effect on the power going into the discharge, and their indirect effect on the possibility of obtaining ignition with an 8.31% methane-air mixture from a resistive circuit. Critical evaluation of the Cadmium disc breakflash (the presently internationally recommended test apparatus). Description of experimental setup and apparatus.

Jan 1, 1974

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By Eugene T. Sheridan

The 25th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, disclosed that 79 companies produced and sold peat from 81 operations in 21 States in 1958. Peat is a carbonaceous deposit, formed under water or in a water-saturated environment from plant material. It is the first stage in the development of coal and, when properly dried, can be used as fuel. Although 98 percent (estimated) of the total world production is used for energy purposes, the status of peat in the United States is somewhat unique in that none is used for fuel, and practically all is consumed as an agricultural product, chiefly for soil improvement purposes. The domestic peat industry has expanded rapidly since World War II, and production in 1958 was 327,813 net tons valued at $3,445,767. More than one-half million ton of peat was consumed in the United State in 1958, however, as 269,096 tons was imported.

Jan 1, 1959

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency In low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were Investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas, The results have been summarized In terms of maximum communication range expected per seam and noise condition. Scatter gain Is further explored as a simple measure of energy coupled to conductors.

Jan 1, 1978

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined to determine through evaluations in two mining companies whether it would achieve measurable improvements. This volume describes the model, how it was applied in the field, and how it was evaluated. Anecdotal data to illustrate common kinds of safety problems and their solutions are included. The literature and field research that preceded the model definition is discussed in Vol. 2, which covers the period of September, 1980 to September, 1981.

Jan 1, 1983

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By Jesse J. Brown

Over 60 simple; were prepared and forwarded to Dr, S. Z. Toma, TPO, PMSRC as a result of this project. Included among these samples were various low temperature forms of silica. Samples of quartz, cristobalite, and tridymite with iron, manganese, and titanium impurities present were prepared. In addition, a long series of samples both wet ground and dry ground for times from 1/2 to 8 hours were prepared. Numerous miscellaneous samples were submitted which included kaolinite, calcite, muscovite, illite, montmorillonite, Ba3(P04)2, and YPO4 among others, in response to special requests from the TPO. The silica rich portion of selected binary (CA 203-Si02, In 203-Si02, Li20-Si02) Na20-Si02, PbO-Si02, SnO2-Si02, Sn02-Si02 BaGa204-SiO2 and SrGa204-Si02) and ternary systems (Na20-Ga203-Si02 and Li20-Ga203-Si02) was investigated to determine the effects of solid solubility on the stabilization of the high temperature forms of tridymite. In addition to the determination of the extent of these crystalline solubilities, observations were made. on the mechanism of the transformation of silicic acid to tridymite and the rate of the reaction in the presence of foreign ions,

Jan 1, 1973

By Liming Yuan

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, causing the gob to breathe out and in. Although the concept of gob ?breathing? is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamics (CFD) simulations were conducted to model the spontaneous heating of coal in longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By R. L. Zick, J. D. Byars, T. P. Mucho

Recently, a large Pittsburgh seam longwall mine was nearing depletion of a major portion of its current reserves and had begun to develop in a different direction from its original portal area to access additional reserves. This meant that a large area of the mine would be abandoned and sealed. However, continued use of the original mine portal area required that the water accumulating in the abandoned mine would eventually need to be pumped to the surface. This would be in addition to the discharge water associated with the new portion of the mine. Several pumping and sump options were investigated to handle the quantity and quality of the anticipated discharge water. This paper describes some of these options, their advantages and disadvantages, and the final engineering decisions. Some problems and unanticipated outcomes, as well as the eventual solutions are discussed, including: (1) estimates of pump requirements, (2) water pool size, (3) eventual water quality, (4) anticipated inflows, and (5) integration into the overall mine water system.

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau's turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987