Search Documents

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

By Douglas Milne

Most empirical and numerical approaches to design in rock mechanics incorporate rock mass classification. Numerical design methods generally use classification values to calculate input parameters for stress-based failure criteria. Empirical methods use classification to allow comparisons between similar rock mass conditions, generally based on a graphical design technique that differentiates stable and failed opening geometries. Classification systems are the best tool available for assessing rock mass properties; however, there are problems with classification systems that should be high-lighted. Rock mass performance can only be realistically estimated by coupling a unique description of the rock mass with known loading conditions. Current classification systems cannot provide a unique classification value. The weightings applied to quantify rock mass properties for classification can result in significantly different rock masses having the same classification values. These weightings have been proven effective for tunnel design and support, but classification systems are now used for many more applications. Rock classification systems evolved from a quick and easy field tool for estimating tunnel stability and support requirements. The need for a rapid field tool means that rock mass classification is relatively insensitive to improved methods of measuring rock mass properties. Problems with classification systems and their application are highlighted in this paper. These problems must be recognized and documented before improvements can be made. An understanding of the evolution of classification systems and their application for both numerical and empirical design approaches is invaluable in highlighting current shortcomings.

Jan 5, 2007

By R. Karl Zipf, David Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a widely-applied method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof, pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, from Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By C. C. Popoff

This report reviews the phosphate deposits, mines, and industry, and prospects in 10 districts covering most of the Montana phosphate field. These districts are discussed individually, and an evaluation of the resources and potential of each is presented. Phosphate rock produced from underground mines in the Garrison district is shipped to Canada for processing to fertilizers, utilized locally for production of animal feed supplement, and pulverized and sold for direct application to the soil. Production from the Melrose district is shipped to Silver Bow and processed to elemental phosphorus. The Maxville-Philipsburg district is destined to become a major producer with the development of the Douglas Creek mine and beneficiation plant by Montana Phosphate Products Co. Montana ranks fourth after Florida, Tennessee, and Idaho in total annual production in the United States. Production him increased from about 60,000 long tons of acid-grade phosphate rock in 1940 to more than 660,000 tons of acid-, beneficiation-, and furnace-grade ore in 1961. Montana has the second largest potential resources in the Western field; in the area south of Butte there are approximately 1.2 billion tons of phosphate rock (+18 to +31 pct P2O5) available above and within 100 feet below entry level; and in the northern part of the field there are about 67.6 million tons available above entry level. In contrast to Idaho, most of the phosphate deposits in Montana are best suited to underground mining.

Jan 1, 1965

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By William H. Schiffbauer, Timothy Lutz, Michael R. Yenchek

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) participated in an experiment to facilitate the remote control of dozers used on coal stockpiles. The experiment consisted of supplementing the normal sensory cues an operator requires to manipulate the dozer from a remote location. NIOSH provided and tested a vision systems intended to give the operator the ability to operate the dozer safely and efficiently from a remote position. This paper highlights the genesis of the experiment, identifies the contributions of Consol Energy and Caterpillar, and details the NIOSH efforts and successful test results. Keywords-remote-control; vision system; stockpiles; safety