Search Documents

By Gerald V. Gibbs

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 0° to 90° for CuKa and from 25° to 180° for CuKa1. The wavelengths used for Cu in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): CuKal 1.54051 A.; CuKa2 1.54433 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn., X-ray diffraction crystallography using tubes with copper targets revealed a need for a handy reference for the quadratic functions of copper radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By R. Stefanko

In this report, the use of Penn State Ventilation Simulator (PSU/MVS) for planning and evaluating new coal mine ventilation systems is demonstrated. The simulator's application to evaluate the ventilation system of a coal mine currently under development is discussed. The ventilation system is evaluated for representing development of the mine at the end of 12, 24 and 36 months after mining has begun. The report describes the necessary steps of data input preparation, ventilation network development, analysis of results, modifications to the network, and methods to expand the computer program for networks larger than 550 branches.

Jan 1, 1977

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961

By Jürgen F. Brune, Liming Yuan, Alex C. Smith

To provide insights and assistances for the optimization of ventilation systems for U. S. under-ground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study is being conducted to investigate the effect of the ventilation scheme on the prevention of spontaneous combustion in longwall gob areas. This report focuses on the flow patterns within the gob under three different ventilation systems; one-entry and two-entry bleederless systems as well as a three-entry bleeder system. The gas flow in the caved gob area is simulated as a laminar flow through porous media while the gas flow in ventilation airways is simulated as a fully developed turbulent flow. The air flow patterns are visualized using flow path lines. Air velocity contours and vector data are also obtained. The possible location of critical velocity zones where the gob is most liable to spontaneous heating is discussed.

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By Wallace W. Key

The California pesticide industry in 1962 consumed about 30,000 tons of clay, talc, limestone, diatomite, sulfur, and other minerals as fillers (carriers and diluents) in pesticide formulation. This was 10 percent of the U.S. filler requirement for pesticides. About two-thirds of the California total was supplied by a few local mineral producers; the remainder came mainly from Florida, Georgia, and Wyoming. The objectives of this report are to provide data on quantities, sources, specifications, and market conditions for minerals used as fillers by California pesticide formulators. The study disclosed that specifications for mineral fillers have become more rigid and formulators have become more numerous in recent years. During 1962 over 1,200 firms registered 16,000 pesticide products with the Bureau of Chemistry in California. Factors which will tend to diminish future need for mineral fillers include the trend toward greater use of organic sprays rather than dusts and further development of biological controls, such as the development of sterile insect strains.

Jan 1, 1965

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By W. J. Huff, G. W. Jones, I. Spolan, R. E. Kennedy

"INTRODUCTION Information on the exploeibility and ease of ignition of acetylene is important in connection with investigations by the Bureau of Mines and others seeking the causes of explosions in medium-pressure acetylene generators.A previous report 6/ gave preliminary results of an investigation made by this Bureau to determine the causes of these explosions. This report indicated the need of amending Federal specifications for ""1/4 by 1/12"" carbide to reduce the amount of fine sizes permitted under the specifications then in force. Tests described in the above report showed that certain sizes of carbide may, under certain conditions, attain excessively high temperatures when acetylene-water vapor mixtures are passed through carbides for extended periods.Federal specifications P-0-101, Amendment 5, June 28, 1944, are now in effect. These latest specifications permit a maximum of 7 percent of ""1/4 by 1/12"" carbide by weight to pass through a 0.0661-inch sieve and a maximum of 2 percent to pass through a 0.0555-inch sieve. Experience has shown that these specifications have insured a safer size range of carbide for medium-pressure acetylene generators.Although the improvement in the size range of the carbides has aided in the prevention of explosions, there have been explosions in which the carbide used at the time of the explosion met the latest Federal specifications."

Sep 1, 1945