Search Documents

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By Tapan Goswami

The main objective of the blasting phase in a coal mining operation is to maximise the coal recovery. However, coal loss due to blasting is a serious problem. The Australian Coal Association Research Programme (ACARP) reported in 2011 that in Australia one in every ten coal mines is completely wasted due to such losses. Coal is either lost in the spoil, largely due to the blasting operation or becomes diluted and cannot be recovered entirely. The major coal loss mechanisms include losses from the coal seam roof, the floor, the front edge and from dilution. Coal damage and loss mechanisms during cast blasting that have been observed by various authors include: •Excessive cast dragging the coal edge in the cast direction. Movements of this nature are oftenassociated with the formation of trenches. •Spatial movement of overburden where rock shears and moves in a plane above the coal seam,which damages and dilutes the coal. •Rock falling over the coal during the blast often producing indentations in the exposed coal. •The inappropriate use of bulk and initiating explosives that often results in coal damage. •Insufficient stand-off distances from the coal. The Australian coal mining industry has gone a long way towards addressing the coal loss issues since 2011: almost all operations now deploy touch-coal drilling and sporadically use gamma logging for loading overburden. A study was conducted to compare the effectiveness of touch-coal information in which some touch-coal blastholes were drilled on a fixed or random pattern. In another study, some blastholes were drilled to the touch-coal, gamma-logged and mapped to determine stand-off distances. It was found that the coal roof surface created by gamma-logged holes was the most effective option for minimising coal loss. As a result, a variable stand-off distance was found to be the key to minimising losses. This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

By Phillip R. Mulligan, Catherine Johnson, Edward Kinzel, Cody Lough, Jason Ho

A shaped charge is an explosive device used to focus detonation energy in a desired direction. Shaped charges have numerous applications in several industries such as oil extraction, weaponry and demolition. The focusing of the detonation energy is the result of the Munroe Effect, which greatly increases the penetration properties of the explosive due to a void in the explosive’s volume. The void in the explosive is lined with a metal substrate that becomes a super-heated projectile when the explosive is detonated. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge. Specifically, hierarchical structuring and functional grading can potentially provide greater velocity, directionality, and efficiency. By utilizing AM, the conventional use of shaped charges can be greatly expanded upon and may open new possibilities. In this work, selective laser melting (SLM) was used to explore different conical shaped charge (CSC) liners made out of stainless steel 304L. A series of liners were tested that had varying densities and were compared to conventional liners. The CSCs were filled with the high explosive Composition C-4 and detonated to evaluate performance. The blast events were recorded using break wire screens to calculate the velocity of the jet through steel target plates over a standoff of 6 times the charge diameter. A high-speed camera recorded the blast event to calculate the velocity of the jet through the air. The depth of penetration into the steel target plates was also used as a measurement of the effectiveness of the CSCs. The aim of this work is to show the potential for advanced shaped charges produced using SLM.

Jan 1, 2019

By Thomas Bakley, Rob Lee, Jay Rodgers

The present state of technology in Controlled Blasting uses standard explosives’ products to create a crack between holes along a desired line of break. The resulting pre-split, post-shear or cut line is often of variable quality with unwanted damage at right angles to the desired cut line. A new concept in Detonating Cord manufacturing has provided a radically different performing explosive. This new Cord has reduced the Velocity of Detonation by more than a third. It changes the Detonation Pressure proMe of Detonating Cord to a lower and longer sustained pressure pulse. In addition, it develops more gas than conventional cords. At the same time it maintains all of the handling and reliability advantages of conventional Detonating Cord.

Jan 1, 2001

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Regina Rocha, Miguel Humpire

One of the challenges within unitary mining operations is blasting, which has a significant downstream impact on the following processes, which is why mining companies ensure the results of the blasting process through joint work with explosives specialists’ companies.

Feb 6, 2023

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By Katherine L. Heineken, Timothy J. Tope, Kim David Murphy

One method for small arms disposal is the use of a deactivation furnace or explosive waste incinerator. There are numerous hurdles a facility typically encounters to get the furnace or incinerator fully operational and permitted. For example, one Department of Defense installation was in the permitting process 7 years, which included numerous facility upgrades and modifications. This paper will discuss the technical approach for proactively addressing permitting issues and requirements and will identify potential pitfalls to avoid as well as ways to reduce costs. For example, when determining the waste profile, the facility should forecast its treatment needs (taking into account the net explosive weight limits of the furnace/incinerator) and then classify the wastes into "chemical families" based on the type and composition of the wastes. One waste from each family should then be selected for potential inclusion in the trial burn. Modeling the waste disposal can help to narrow down the number of wastes requiring characterization during a trial burn, as well as the number of analyses.

Jan 1, 1997

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By M R. Hettigner, J Nawrocki, C E. Johnson, P G. Cahill

This study evaluates the effects of both short inter-hole and intra-hole delay times on rock fragmentation and throw. Full-scale test blasts were analyzed at a granite quarry in Talbotton, GA. This analysis provides a representative understanding of timing effects on fragmentation in the field, different from previous lab scale studies that negate the effect of geology. Inter-hole delay times between 0 ms and 25 ms were tested on a series of 4 bench blasts and subsequently examined using photographic fragmentation analysis methods.

Jan 1, 2017

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Ken Tunnel

In the spring of 2005, the Lake Superior Chapter of the ISEE invited me to speak about raw materials used for blasting, anhydrous ammonia and the effect of this important feedstock on the cost of ammonium nitrate.The invitation was extended because our company is involved in trading ammonia and the production of ammonium nitrate. In a response to a request to update that presentation, it struck me how events such as hurricanes Katrina and Rita can change the landscape of our businesses.

Jan 1, 2007