Search Documents

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By Silvia França, Hudson Couto, Renata Barbosa

"The flotation process, largely used for mineral concentration processes, which is based on air bubble adhesion to the dispersed solid phase, is also being used for wastewater treatment purposes. Dissolved air flotation (DAF) is based on the separation of the solid-liquid phases with the aid of small air bubbles (10-100 µm), with high values of interfacial contact area, improving the process efficiency. In the process, the air bubbles and particles or flocs form aggregates, which rise to the surface of the flotation cell to be collected. The advantage of producing small bubbles is directly related to the fact that smaller bubbles result in greater bubble-particle interaction. Wastewater produced in alumina refinery - from the red mud filtration step - has a red colored aspect due to the presence of very fine particles of red mud and also dissolved matter that still remain in the filtrate. This wastewater might be treated, aiming to reuse the water in the refinery or discharge it properly in the environment. The aim of this study was to evaluate the DAF process efficiency for the treatment of red mud wastewater in order to decrease suspended particles and dissolved solids contents, in addition to mitigate the high causticity of this wastewater. The process efficiency was evaluated by comparing turbidity removal and total solids concentration in the treated wastewater to the feed. The influence of important variables of the DAF process as type and concentration of coagulant and flocculant were evaluated. It was possible to obtain good turbidity removal efficiencies (up to 90%) using low concentrations of coagulant (50 mg/L) and flocculant (0.5 -1.0 mg/L). In addition, for most of the experiments, the specification for effluent diposal, according to the Brazilian environmental regulation 430 (Conama, 2011): pH range 5 to 9 and turbidity < 40 NTU, was attained. These results emphasize the possibility of using the DAF as an alternative technique to settling and filtration process, that are traditionally used, for treating wastewater from the alumina industry, allowing the reuse of water in the plant or adequate discharge with less environmental impact."

Jan 1, 2014

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014

By Valentin V. Shatalov, Irina V. Pastukhova, Alexander V. Kurkov

"We have developed a technology to improve the quality of low-grade concentrates containing minerals of tantalum, niobium and tin on the basis of given conception by the way of improving selectivity and using certain reagents composition. The basic collector presents a traditional or complex-forming collector used together with organic diphilic reagents – the secondary reagents regarding the basic flotation regiment, capable of forming associates with the main collector on the surface of the mineral, thus altering the interaction energy. In the given process the main collector is the fraction of hydroxamic acids C7-C9, the reagent of the secondary action – sulphosuccinamate, which added in moderate concentrations range provides for a synergistic effect.We have determined the parameters of the process stability and necessary modifying reagents for a selective recovery of tantalum, niobium and tin minerals from refractory products. Variants have been studied where the main collector and the secondary action reagent were substituted with some more efficient flotation reagents. A possibility of a more flexible reagent compounding for the process has been shown. The flotation process is highly stable regards the saline composition of the liquid phase in the pulp. It can operate under conditions of the complete water recycling with the total salt content up to 12 kg/m3, iron up to 1.2 kg/m3.The given results consider the efficiency testing of the suggested technology for the gravitation products, which were obtained from ores of various genesis and contain large quantity of the most refractory minerals, such as topaz (80%), gamet (55%), tourmaline (30%). High selectivity of the process has been registered with the metal recovery about 92-98%, which appears to be similar to hydrometallurgical operations under certain conditions."

Jan 1, 2003

By Peter Ay, Matthias Schmidt, Christian Stollberg

"The aim of the study is the development of a seamless reprocessing procedure for plastics from automotive parts which are to be recycled (figure 1). Before automatic sorting can be performed, the materials first have to be identified by a near and middle infrared (NIR/MIR) system.Materials reprocessing basically includes research on size reduction, decoating, and roughening of the materials. Variants of the necessary technologies such as different shredders and mills and physico-chemical or mechanical decoating and roughening procedures together with the fundamental approaches underlying these methods are investigated and benchmarked. This allows the theoretical determination of the impact of each method not only on the overall process but also on the result achieved within the identification and sorting procedures."

Jan 1, 2003

By Z. Kwela, A. Manhique, W. W. Focke, W. van der Merwe

"The main features of the de Wet improved alkali fusion process for the manufacture of AZST are: Fewer process are steps necessary; radioactivity is removed by leaching rather than by precipitation; fewer waste streams are generated; there is less waste to discard and alkali reagent is recovered in the form of a sodium silicate solution that is essentially free of radioactivity.Here we report on our efforts maximize the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated. The fusion products were characterized by infrared spectroscopy, X-ray diffraction and by wet chemical analysis.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since these compounds do not hydrolyze in water they limit the recovery of alkali in the sodium silicate product stream. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed."

Jan 1, 2003

By Claudia Ríos Figueroa, Gonzalo Montes-Atenas

"Among the many variables mentioned in the literature that may influence the froth flotation performance, particle size is perhaps one of the most renowned. Empirical knowledge has indicated that recovery of fine particles will inevitably drop below certain particle size threshold. Several processing alternatives have been suggested to improve the recovery of fine particles. Some of these initiatives have been reached the status of patents and other intellectual property related documents; however, there is still a disconnection between the scientific knowledge available and the industrial operations practicalities implemented to address this matter. In fact, in general terms, none of these ideas or processes concepts have become a final solution to this problem. At first glance, economical reasons may be argued as the main cause hindering the development of these and other ideas, but it would be an oversimplification as technical issues behind them are still themes to be discussed and sorted out. This study aims to review technical aspects behind scientific ideas and processes concepts suggested to solve the problem of low beneficiation of fine particles in froth flotation. The analysis was performed using the theory of inventive problem solving (TRIZ) which allows identifying technical gaps these initiatives have not considered or overlooked. Statistically the scientific databases indicates that reports on fine particles froth flotation only represented less than 50% of all reports involving fine particles processing. Most of the solutions derived from classic contradictions derived from bubbles and particles hydrodynamics only (reducing the bubble size or increasing the turbulence would increase the rate of bubble-particle aggregates formation but may reduce the recovery). This contradiction encompasses a small range of contradictions possible to be accounted and to be resolved. The method is expected to provide insights towards designing definitive solutions for the industry in this field."

Jan 1, 2014

By U. M. J. Boin, E. V. Verhoef

Pyrometallurgical reactors constitute a key processing component in the total primary and industrial/recycling resource cycle, being involved both in primary smelting, converting and extraction, as well as the reprocessing of scrap, from aluminium cans to end-of-life automobiles. Therefore the pyrometallurgical reactor?s role in achieving sustainability is the central theme discussed in this paper since optimising their operation minimises waste, residue and offgas (NOx, dioxin, CO2) and maximises product quality and therefore efficiency. To effectively control the overall resource cycle, one needs to take a systems modelling approach of the whole cycle, seeking to also understand the dynamic process behaviour of the individual components of the cycle, and then especially the part that contributes most to the chemical conversion, namely the pyrometallurgical reactor. This paper highlights the role of pyrometallurgical thermodynamics in the whole resource cycle and specifically places equilibrium thermochemistry in the context of process dynamics where large, variable inventories are recycled or maintained within the system. This paper will therefore review the semi-empirical dynamic modelling tools, which are used to model complex systems with the specific goal of developing dynamic predictive models, which also include slag-alloy chemistry, towards controlling the recycling in a feed forward manner. To illustrate the primary production of metals, high carbon ferrochrome and Ni-Cu-matte smelting will be presented as a brief case study. Also fundamental studies in blast furnace and waste incineration kilns will be given. It also will show how the distributed nature of the chemistry of melts in the case of primary extraction, and industrial (recycling) materials such as recycled end-of-life vehicles, have a significant impact on the process outcomes and model predictions. It is therefore argued that the fundamental thermodynamics and kinetics in metallurgical reactors play a final crucial role in modelling the closed material cycle, but only when it is used in conjunction with process systems theory based on reconciled data for parameter estimation and model calibration. System models for aluminium and car recycling will be given as well as a dynamical system model that describes the interconnected material flows for Ag, Au, Bi, Cu, Fe, Ni, Pb, PGM, Sn and Zn for a study on lead-free solder.

Jan 1, 2003

By Bhargav Dhavala, Sristy Raj, Ashok Kumar, Suman Krishna Sit, Adity Ganguly, D. P. Chakraborty

"Tatasteel’s West Bokaro washery#3 is designed to deslime raw coal at 0.5mm; the oversize (+0.5mm) is beneficiated in dense media cyclones (DMC) while the undersize (-0.5mm) is beneficiated in froth flotation (FF) cells. Nearly, 80% of the raw coal feed reports to the DMC circuit consisting of four parallel streams. Presently, the performance of DMCs at washery#3 is interpreted by: (a) comparing the actual plant yield w.r.t the lab predicted yield and (b) misplacement of clean coal to middllings.However, the comparison between actual & lab predicted yield is fallacious given the fact that the lab predicts yield of the borehole sample while the feed received at the plant has different characteristics altogether due to the dilution during mining. To mitigate the said limitations, a quick diagnosis tool using the past data has been developed that will give a prediction of performance of different coal seams in the DMCs, inputs being feed ash to DMCs and stream wise feed specific gravity (coal & magnetite combined).The tool also will help in identifying the root cause on real time basis thereby helping the operator to take necessary corrective actions. The operator can intimate the mining personnel in cases of shale reporting to the feed as a result of dilution during mining. In events of higher standard deviations between the parallel streams w.r.t feed specific gravity, the operator can adjust the parameters accordingly to minimize the yield loss. INTRODUCTION West Bokaro came into existence in 1948, as an independent coal company, managed by M/S Anderson Wright. Tata Steel acquired the Company in 1956 to meet its requirement of metallurgical grade coal for Iron making. Subsequently, in 1976, it was made a division of Tata Steel. In 1974, when coal mines were nationalized, West Bokaro was exempted as it produced coal only for captive consumption of the Steel Works. The first washery of India was set up in West Bokaro. The business objective of the West Bokaro division is to produce clean coal at optimum cost for captive use in the steel plant of Tata Steel at Jamshedpur. The strategy is to reduce ash with minimum loss of yield so that quality of coal improves and yet the cost is beneficial vis-a vis imported coal. The primary product is the metallurgical grade coal for coke ovens, which converts coal into coke for use in the Blast Furnaces."

Jan 1, 2018

By X. Y. Zeng

Most Chinese titanium bearing minerals are the composition of magnetite vanadium and ilmenite. All of such mineral processing plants use low intensity magnetic separators to recover magnetite and vanadium goes with magnetite. In the past years most of the plant tails containing about 10% TiO2 were abandoned. Now many of these plants use SLon magnetic separators to recover ilmenite in the roughing stage, which can throw away most of the gangs and slimes with very low cost. The new development of applications of SLon magnetic separators in Chinese ilmenite processing industry is introduced in the paper.

Jan 1, 2014

By Ashish Agarwal

For a correct evaluation of the performance of any process, it is important to reconcile the data gathered in the plant from the material balance point of view for all the streams flowing in and flowing out of the process unit. There are two main approaches to reconciliation of data, which involve minimization of the sum of the squares of: (i) the closure residuals and (ii) the component adjustments; both weighed with the estimated variances of the components. Though, these approaches have served us well, it has not been possible to ascertain if the reconciled values for various components and the split factors obtained using these approaches are truly the best estimates. In this paper, this aspect has been investigated by analyzing pseudo-experimental data of known error structure on size classification of particles in a hydrocyclone. Three types of basic error structures were considered for the measured component values: absolute error, relative error and chi-square error. The error structure was modified by adding a random component of error using normally distributed random numbers corresponding to zero mean and different levels of variance. By carrying out a large number of simulation experiments, it has been shown that in the presence of random errors, irrespective of the basic error structure of data, which is usually unknown, the chi-square error minimization criterion can be used to obtain most reliable results. Keywords: data reconciliation methods, chi-square error minimization

Sep 1, 2012

By M. R. Tavakoli Mohammadi

Novel solvent extraction technologies in recent decades have made attempts to show the problems in applying this method for dilute solutions and find appropriate solutions to overcome them. Improving the equipments performance used in this method for dilute solutions, cause development of usable resources and reduction of operational costs. Furthermore, appropriate conditions provide for using dilute solutions produced in various industries as a new source of valuable elements. Thus, this proposal can be a very good solution for treatment of these solutions and reduce the environmental impacts associated with them. The purpose of this study is to introduce a new method of Column Floto Extraction (CFE), which has been invented in this regard. In this method, using spargers similar to Jameson cell downcomer in floatation process, the organic phase bubble dispersion has been used instead of its drop dispersion in aqueous phase for the two-phase mixture operation. This operation mode has caused a higher extraction percentage of solute in high aqueous to organic ratios due to enhancement of contact area. In this study, in addition to explaining the advantages and features of this method, we have dealt with its design and performance mode.

Sep 1, 2012

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By Miguel Becerra, Daniel Jordán, Jorge Soto, Luis Torres

"Most SAG grinding operations currently use ball sizes between 5.5 and 6 inch maximum size. However, in most cases the use of this ball sizes hasn’t been justified by a phenomenological analysis of the real effect on the grinding process, but rather by trial and error. The analysis of the influence of ball sizes in SAG grinding hasn’t been developed in detail by considering the effect on process parameters inside the mill, grinding efficiency or internal classification. Historically a conventional grinding reference has been made on the empirical procedure developed by Azzaroni (1980). Further to Azzaroni’s methodology, Sepulveda (Sepúlveda, 2007) developed the SPEC methodology, incorporating the ball size effect on the grinding efficiency parameters using a population balance model included on Molycop tools spreadsheets.This paper demonstrates a detailed analysis at pilot scale of the ball size employed in SAG grinding and scaling that exists between the different levels. This analysis includes assessing the effect of balls sizes on parameters associated with grinding efficiency and its effect on the total fill level, product size distribution and specific energy consumption, among others. In a complementary way it develops a technical - economical evaluation from industrial data comparing two different ball sizes and its effect on the grinding process analysed integrally."

Jan 1, 2014

By T. Onnela

Metso Mining and Construction Technology is one of the world leading suppliers of equipment and knowhow for aggregate and mining industry. The processing capacity, ease of use, and reliability are featuring Metso?s state-of-the-art cone crushers. Crushing is a complicated process affected by numerous parameters. The optimized crusher kinematics is one of the key factors for high performance. To fine tune the crusher kinematics and crushing chambers one needs to know how different parameters affect. The main cone crusher parameters are head angle and diameter, gyration point, shaft speed, eccentricity, stroke length, and inclination and design of crushing cavity. Selecting the correct combination of these parameters is a multi task optimization challenge. In practical life there are more factors to achieve satisfactory performance, like crushing chamber wear and profile management keeping the performance constant over the whole wear life, control of crusher frame loads, ability to handle disturbances in feed material etc. The extensive research work has lead to a solution that enables the highest possible material density in the crushing chamber. This design provides maximum reduction of processed material and thus increased share of 0/10 mm product. High density in the cavity offers further benefits, such as high throughput capacity, less material contact with wear parts and even load on crusher frame and bearings. The challenge that an equipment supplier involved with high density crushing is how to design a robust cone crusher, which is able to cope with the high crushing forces due to high resistance from the crushed material against the gyration movement. Metso has launched a new series of cone crushers HP3, HP4 and HP5 that are all able to work in high density crushing applications The test results and evidence from over 300 installations clearly prove the effectiveness and importance of high density crushing. Keywords: cone crusher, crushing chamber, crusher kinematics

Sep 1, 2012

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By X. M. Wang

Magnetic floatation column (MFC) is a new equipment used for increasing content of iron, in which magnetite is separated in open gradient magnetic field. Simulation study was performed to investigate the separation characteristics of the separation method by analyzing the dynamic motion of magnetic particles. In this paper we compare two magnetic fields created by different magnets. The obtained simulation results give perspective in industrial design of MFC as the basis stage.

Jan 1, 2014

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By Yuexin Han

The wet preconcentration of haematite, comminuted by high-pressure grinding roller was studied, using the cylindrical ferromagnetic medium. The effects of various factors including rod diameter, rod gap and background magnetic field intensity (BMFI) on the performances of preconcentration for different size fractions and the force analysis of single mineral particles with different diameter in the separation zone were emphatically investigated. The results showed that as the rod diameter increased, the rod gap decreased, and the BMFI increased the tailings grade and the tailings yield reduced while the concentrates recovery raised that was regardless of variations in feed size distribution. For the -3.2+0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 7 mm at BMFI of 454kA/m is used to get a higher performance. For -0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 4 mm at BMFI of 263kA/m is used to get a higher performance. After the classifying preconcentration, at the optimum condition, the overall concentrate grade increases by 9.56 percentage points and the concentrate recovery is up to the 82.67% with a tailing grade of 10.68% and a tailing yield of 40.31%. The magnetic force, exerted on weekly magnetic minerals was proportional, to the specific susceptibility and square of BMFI. For the same BMFI, the magnetic capturing force on coarse particles increased, and that on fine particles decreased with the increasing of rod diameter. For the lean locked-particles, considering the gravity and viscous resistance of particles, rods with a big diameter were beneficial to the capture of coarse particles and had no influence on the capture of fine particles, while rods with a small diameter were good for the capture of fine particles and not suitable for the capture of coarse particles of lean locked-particles. Keywords: low grade haematite, high-pressure grinding roller, high intensity magnetic separation, pre-concentration

Sep 1, 2012