Search Documents

By Arkady Senchenko

The application of centrifugal separation methods with the use of gravity concentrators has been assigned high priority while gold-containing minerals processing. The separation proceeds under centrifugal force resulted from the rotor spinning and wash water flow in the concentrators. The high specific gravity particles are retained at the trapping surface of the cone, and the low specific gravity particles are brought in the tailings. The centrifugal field in such concentrators (Knelson, Falcon) is generated by the rotating cone provoking the swirling of the free fed slurry flow. The author investigated the regularities of the separation process in the centrifugal gravity concentrator where a two-phase flow of the separated mineral media is under the pulsed pressure of the fluidization water and air. As a result of the study the possibility of the deeper penetration of the fine heavy fraction into the cone rings, providing the fluctuation of the fluidization water or air flow, was theoretically argued and experimentally proved. This allows the increase of the separation performance at low pulsation costs. The developed mathematical models are in close conformity with the actual process of interest and they enable the prediction of the heavy phase behavior at the isolated process stages in the concentrator. Keywords: gold, centrifugal gravity concentrator, containing, specific gravity, cone ring, pulsation, cost, fluidization water, Knelson centrifugal separator

Sep 1, 2012

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure for the predictive simulation of flotation circuits far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, circuit survey and laboratory batch flotation data collected from an industrial flotation circuit are analysed. The data demonstrate that streams in an industrial flotation circuit exhibit varying particle floatability – concentrate streams typically float faster than tailing streams (Figure 1(a)). This floatability, however, is generally conserved around the various units within the flotation process (i.e. the effective floatability of the combined feed and product streams of a unit is equivalent (Figure 1(b)))."

Jan 1, 2003

By Andrzej Luszczkiewicz, Tomasz Chmielewski, Jan Drzymala, Andrzej Konieczny, Rafal Kaleta

Properties of the sedimentary Polish copper ore mined from the Legnica-Glogow Copper Basin (SW Poland) by KGHM Polish Copper S.A. were presented and currently used beneficiation technologies were described. Due to a unique lithological layered structure of the polymetallic deposit and existing mining system, the ore currently processed in the three KGHM concentrators is very complex with variable content of the carbonate, sandstone and shale fractions. The mined copper ore contains from 0.8 to 1.8 % Cu and Ag, Pb, Zn, Ni, Co, V and Mo as accompanying metals. The paper presents difficulties in upgrading the LGOM ore and selected possible solutions and development concepts of its processing. The first one is a chemical treatment with controlled amount of sulfuric acid of special product of flotation such as for instance middlings. The acid treatment leads to increased liberation of copper minerals and better further processing. Another concept is atmospheric leaching in oxygenated sulfuric acid and ferric ions solution as the major unit operation applied to selected low grade final flotation concentrates or flotation by-products. The third approach, based on copper ore pre-flotation with a frother to partially remove Corg, is also considered.

Jan 1, 2014

By B. Y. M. Bueno

Biosorption of heavy metals can be an effective process for the removal of heavy metals ions from aqueous solutions. In this study, the adsorption properties of Rhodococcus opacus biomass for Pb(II) and Cu(II) ions was investigated. The effects of initial pH, initial metal concentration and biomass concentration on biosorption efficiency were studied in a batch system. Results showed that the initial pH would play an important role in the Pb(II) and Cu(II) ions removal by R. opacus and affected the zeta potential of R. opacus. The equilibrium adsorption was reached with 60 min. The Langmuir and Freundlich models were used for describing of adsorption isotherm data. The maxi-mum adsorption capacities of biomass were determined as 94.3mgg-1 and 32.2 mgg-1 for the Pb(II) and Cu(II) ions, respectively. The experimental data fitted to pseudo second order kinetic model. Adsorption capacity of Pb(II) ions was found to be reduced by the presence of the other competing metal ions in the system. The FT-IR results of R. opacus biomass showed that biomass has different functional groups and these groups are able to react with metal ions in aqueous solution.

Jan 1, 2014

By John A. Rumball, Martin R. Houchin

"For gold leaching of oxide ores, the optimum cyanide : oxygen ratio is approximately 106 mg/L NaCN : 10 mg/L O2 (6.9:1 by mole). In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio such that leaching may occur in a relatively low dissolved oxygen (DO) environment.RESULTS AND DISCUSSIONGold leaching in a carbon in pulp (CIP) and carbon in leach (CIL) circuit is driven by the supply of cyanide and oxygen, as described by Elsner’s equation (1):• 4Au + 8CN- + O2 + 2H2O ? 4Au(CN)2 - + 4OH- (1)Equation 1 suggests that the ideal molar cyanide : oxygen ratio should be 8:1, or 122.5 mg/L NaCN to 10 mg/L of DO. It is generally accepted however, that oxygen is not completely reduced to hydroxide at the gold surface, and that equation (2) better represents the gold leaching reaction (Marsden and House, 1992):• 4Au + 8CN- + 2O2 + H2O ? 4Au(CN)2 - + 2OH- + H2O2 (2)Additionally, since gold leaching is limited by either the diffusion of cyanide or oxygen to the gold surface (Habashi, 1993), then the relative diffusion rates of cyanide and oxygen must also be taken into account. Marsden and House (1992) suggest that the ideal molar cyanide : oxygen ratio is 6:1, while a more recent investigation using laboratory and plant observations (Heath and Rumball, 1998) suggested a molar ratio of 6.9:1.In practice, although a cyanide : oxygen mole ratio of 6.9:1 applies to some circuits, there are many instances when this is not the case.In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio. Galvanically connected sulphides, and possibly carbon, provide a large surface area for oxygen reduction. As the cathode surface area increases, the oxygen concentration required to sustain the same rate of gold oxidation decreases proportionately.Galvanically connected particles may be composite particles, however they may simply be liberated sulphides in the same suspension as the gold. Particle collisions within a slurry are sufficient to provide momentary galvanic connection (Greet, 1995)."

Jan 1, 2003

By H. J. Schulze

From a colloidal science point of view (Schulze 1984, Nguyen & Schulze, 2004) five micro-processes are responsible for successful particle-bubble formation: the approaching of the particle to the liquid-air interface, the thinning and rupture of the intervening liquid film, the expansion of the three phase contact perimeter, the generation of sufficient large capillary force to stabilise the aggregates and the transport process of particles into and within the froth layer. Flotation reagents influence mainly the thinning and rupture of the intervening liquid film between particles and air bubbles, the expansion of the three phase contact after the rupture of the liquid film and the stability of the aggregates against external destruction forces in the flow field. But it exist also a non-negligible influence on the approaching of particles to the bubble surface during the encounter process and on their passing over into the froth layer and the froth stability.

Jan 1, 2003

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By I. N. Gridasov, V. V. Khromov, R. I. Ismagilov

"Over 50 mln.tonne is the average annual output of oxidized ferruginous quartzites typically containing Fe38-42% mined in Mikhailovskoye ore field. The most promising and cost-effective way to expand concentrate production maintaining current output of magnetite is processing of oxidized ferruginous quartzites (hereinafter referred to as OFQ) mined as a by-product in Mikhailovsky open pit mine. However lack of proven and efficient concentration and agglomeration process applicable to OFQ and insufficient data for feasibility evaluation of OFQ processing encumbered full-scale addressing of this challenge. Based on outcomes of multiple various studies a process of OFQ flotation was designed by MC Metalloinvest LLC and PJSC Mikhailovsky GOK engineers. Comparative lab-scale testwork have proven performance and production advantages of flotation against magnetic separation feat. flotation and combined concentration method. Lab-scale flotation enabled production of concentrate with average Fe66.6% and SiO22.06% grade. Geologic and production contouring of OFQ deposited in Mikhailovskoye ore field has been carried out to collect necessary data for feasibility study incl. cost and profit estimation. As a result processing and production properties of over 3,500 samples have been analyzed which is characteristic of every direction and level of prospective ore mining within Mikhailovskoye ore field up to year 2032. Following work has been done based on geologic and production contouring of OFQ: – natural typification of ores and production (processing) grades of OFQ, determination of average mineral composition; – correlation analysis of interrelation between OFQ mineral composition and processing features thereof for overall bulk of samples as well as for individual data blocks related to various directions of open pit mine; – OFQ classification with account of defined mineral composition and processing features. Total Fe weight content in chamber product of flotation (known as concentrating ability in flotation) was applied as a major differentiating factor for processing grade classification of OFQ. Three processing grades of oxidized ferruginous quartzites were established as a result of flotation tests run to determine concentrating ability, i.e. – hard concentrated OFQ (TO) – below Fe65%; – mean concentrated OFQ (SO) – Fe65-67%; – easy concentrated OFQ (LO) – over Fe67%. Outcome of this work provided initial data for feasibility study and cost-profit evaluation of medium-term industrial-scale processing of OFQ deposited in Mikhailovskoye ore field."

Jan 1, 2018

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003

By I. I. Maximov

The paper describes the results of studies performed with a view to develop an improved technology for processing high-grade massive and cupriferous ores of the Talnakh deposit, the main valuable components being nickel, copper and PGM. The studies? main task was production of nickel concentrate with nickel content of approx. 15%, nickel recovery being as high as possible. The studies were performed on two ore samples. One sample was a mix containing high-grade massive (78%) and cupriferous (22%) ores with nickel content of 1.93% and copper content of 3.6%; the other sample was a mix of high-grade ores with nickel content of 2.25% and copper content of 3.72%. Main ore minerals were copper sulfides ? chalcopyrite and cubanite, their total content being 10.5% ~ 11%, pentlandite (5.2% ~ 6.1%) and pyrrhotite (36.7% ~ 42.9%). Influence of grinding media on pentlandite and pyrrhotite separation results, achieved through combined use of triethylenetetramine (TETA) and sodium sulfite (SS), was also investigated. It is shown, that combined application of TETA/SS in the ratio of 1:2, permits to grind products in metal mill (mild steel) with metal balls (mild steel), achieving results that are similar to those achieved by means of grinding in inert grinding media with TETA/SS ratio of 1:1. Application of the developed technology provided for production of high-grade nickel concentrate with nickel content of 14.7% ~ 15.6%, nickel recovery being 76 % ~ 77%. Earlier experiments performed on the above mentioned ore mix permitted to produce nickel concentrate with nickel content of 10%, nickel recovery being 75.9%. Consequently, nickel content was increased by 4.7% ~ 5.6%, and a higher nickel recovery was achieved. The paper also describes metallurgical results related to nickel, copper and PGM with regard to all processing products.

Jan 1, 2014

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By A. Lewis

"Thiol collectors including the xanthates and dithiophosphates have dominated the sulfide mineral processing industry for over a century. Tecflote represents completely different chemistry, without sulfur or phosphorus, and will float all sulfides and associated precious metals. As these collectors are surfactant in nature, they comprise a head group which binds to mineral surfaces, a spacer and a long hydrophobic tail. The modification of the spacer behind the head group allows for collector optimisation for different sulfide ore types and process conditions.The Tecflote surfactants have been designed to be either very selective against pyrite at the natural pH of the ore (pH 7-9) or to float all sulfides including pyrite. Depending on the ore type and the process flow sheet, the use of lime can be maintained, reduced or completely eliminated.Tecflote can be used either as a rougher collector giving good recovery and grade for the sulfide minerals or it can be used to target valuable minerals after regrind and through cleaner flotation. It has repeatedly shown to be very effective at holding onto gold through the cleaner steps. The low solubility has a significant impact on the mechanism and surface activity of the collector, resulting in a very different flotation response compared to conventional thiol collectors.INTRODUCTIONXanthate was first made in 1882 by Zeise and first used in flotation in 1924 (Keller, 2018). In 1946 Keller patented thionocarbamate as a collector, which was produced by Dow Chemicals (Keller, 2018). Later it was replaced by Dow product Z-200, while dialkylthionocarbamate was discovered by Harris et al. (Harris, 1954. No significant chemistry change to collectors has occurred since they were introduced in the mid-20th century and now that the feed grades have been declining over the last decades creating a need to find more selective collectors to extract difficult and complex ores and pushing the industry to look at other reagents."

Jan 1, 2018

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By M. A. C. Goes

Over the last twenty years CETEM has been involved in the preparation and certification of reference material from ores, concentrates and related materials for use in analytical laboratories associated with mining, metallurgy and earth sciences. CETEM provides reference materials from mineral samples, not available from the existing sources, to meet the needs of the mining and mineral industry. CBPA-1 and CBPA-2 respectively are samples of copper sulphide ore and flotation concentrate, both originated from Sossego Mine, located in Pará State, Brazil. The batch characterization was carried out by a collaborative measurement program with participation of 20 industrial, commercial and government laboratories from South America, North America, Europe, Asia and Africa. The certificates and report were issued in December 2007 (http://www.cetem.gov.br/ mrc/ing). The objective of this paper was to describe the procedures for material preparation and the collaborative approach involving a collaborative interlaboratory measurement program to certify CBPA-1 and CBPA-2.

Jan 1, 2014

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"The valuable materials resulting from the processing of gold-bearing ores are often refractory to direct gold recovery through cyanidation. There are multiple methods for chemical liberation of gold prior to cyanidation such as pressure and biological oxidation as well as atmospheric oxidation which is typically used in combination with physical activation of material by ultrafine grinding such as the Albion ProcessTM. This paper will examine the data from process testworks carried out to estimate the efficiency of the Albion Process™ for the oxidation of materials with a wide composition range prior to cyanidation. The data will be compared to that obtained by direct cyanidation of the feed (without oxidation) and from the testing of pressure oxidation on the feed prior to cyanidation. Albion Process™ tests were conducted in Institute TOMS with participation of Glencore Technology Pty Ltd (Australia). Refractory concentrates obtained from the ores of several Russian and CIS deposits were used as feed for the testing. These concentrates were also subjected to a material composition study and testing using conventional recovery methods. The resulted test data make it possible to perform an integrated assessment of process properties for materials with different compositions, compare performance of various process flowsheets for the materials under study, and conclude on efficiency of Albion Process™ application for gold recovery from refractory materials different in their composition.INTRODUCTION It is often the case that gold ore concentrates are refractory to gold recovery by direct cyanidation. This refractory nature is as a rule attributable to fine gold dissemination in minerals, most often in pyrite and other sulphides, as well as to the increased amount of components impeding cyanide leaching of gold due to cyanide consumption and reducing process conditions. The refractoriness of the concentrates results in low gold recovery values when conventional cyanidation technology is used. In this context, various additional processes are applied to breakdown such refractory sulphide concentrates, i.e. mechanical breakdown (fine and ultrafine grinding), chemical breakdown (atmospheric oxidation, e.g. Leachox, acid-oxygen oxidation, pressure oxidation – POX, bacterial oxidation – BIOX), and thermochemical breakdown (various roasting methods). Such breakdown processes allow for increase in recovery of finely disseminated gold during the downstream cyanidation, however, their application is cost-intensive and does not always ensure economic benefit."

Jan 1, 2018

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By Milind Chikhale, Ranjeev Kumar, Keshav Tyagi

Ore characterisation including mineralogy and beneficiation testwork of an ore is very important for determination of possible products and their quality. The results of such study help in ascertaining the beneficiation process route for the ore. The present study deals with ore characterisation study and beneficiation testwork on the samples of hematite iron ore with goethite impurity. The characterisation study reveals that the hematite is under alteration stage to goethite which has become an integral part of hematite. High goethite/limonite content is enhancing the loss of ignition content of the ore and reducing its Fe content. The findings indicate that in case of hematite iron ore associated with goethite and limonite, it is difficult to achieve high grade of concentrate above 65% Fe. It depends on the amount of goethite and limonite minerals and their association with hematite. These minerals contain aluminous impurities and hence, their rejection becomes essential. Separation of limonite and of goethite to limited extent is possible. In case of goethite, effective liberation is not achieved where it occurs as surface alteration product of hematite grains. The gangue mineral reported are clay and gibbsite, and are closely associated with iron minerals. The test work results indicate the grade and recovery of Fe along with alumina and silica content in lumps, sinter fines and pellet feed fines that can be achieved for the different ore types vis-a-vis the percent of available hematite in the ore. The recovery of iron is dependent on the hematite available and the loss of iron values in tailings is more because of rejection of limonite and goethite.

Jan 1, 2014

"The research aimed at solving the problem of measuring instantaneous local physical quantities for multiphase flows in mineral processing, which are common in minerals industry and with significant challenges. Due to the lack of proper measurement tools currently in minerals industry, multiphase flows (such as in flotation cell) are treated as in a “black-box”. It is crucial to develop measurement technique by which the acquired processing data can be used for process optimization and control. By measuring the conductivity distribution across a measurement area, Electrical Resistance Tomography (ERT) has been adopted by many researchers to monitor and investigate many processes involving multiphase flows in other industry sectors. A compact ERT probe was built and then used to measure the conductivity distribution within a few flotation machines. In a flowing foam flotation column, the results showed that ERT can accurately measure the change of liquid content (high conductivity fluid distribution). In another part of work, based on the Green-Kubo relations, ERT can measure turbulence via the fluctuation of conductivity caused by bubbles moving through the measurement area, changing the density of the fluid. The tests with the Metso 3 m3 RCS flotation cell were also carried out for turbulence measurement under different air rates and impeller speeds. The results of flotation cell from ERT measurement showed that varying impeller speed had more pronounced influence than changing air rate. When impeller speed is increased, the size of the high turbulent zone increases. ERT is a powerful technique that has the potential to be used for a wider range of applications. The future work will be carried out with more case studies and expanded to more processes such as leaching process, high temperature flows in further downstream production chain (steel making process and alloy manufacturing process).INTRODUCTIONMultiphase flows constitute a majority of the naturally-occurring and industrially-relevant flows, especially in mineral processing. Some of the measurement techniques have been used for the study of fluid characteristics. Optical techniques such as Laser Doppler Anemometry (Kyselaa et al., 2013) and Particle Image Velocimetry (Nobach and Bodenschatz, 2009) can produce accurate measurement results with high spatial and temporal resolution, but their applications are limited to transparent flows. Hot wire probes (Amini et al., 2013) have high spatial and temporal resolution in turbulence quantification, but they are susceptible to environmental factors."

Jan 1, 2018