Search Documents

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

"The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed.The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters as shown in figure 1."

Jan 1, 2003

By V. Avzian Belozersky reg 453524, Vasily V. Lodeischikov, Adolf F. Panchenko, Til E. Vidusov, Olga D. Khmelnitskaya, Vladimir E. Dementyev

"Presently, there is a number of gold deposits which cannot be developed using the conventional technologies with acceptable economic indices due to low gold content, high depth of ore occurence and other conditions. For such ores, an innovation technology of underground gold leaching in the place of their occurrence is of special interest. The technology excludes ore mining and hoisting to the surface. This enables the production cost of 1 g of gold to be considerably reduced in comparison with conventional methods of gold recovery.The Maminskoye deposit oxidized ores were chosen as the subject of underground leaching because they are ideally suited for this purpose due to their composition and hydrological parameters. The ore reserves within the underground leaching block are 90, 000 t with 0.7 g/t average gold grade.An experimental system for underground leaching with a throughput of 15 cubic m solutions per hour was developed. A combined filtration-and-infiltration system of the ore massif development by holedrillingwhere pregnant solutions are air-lifted was worked out.The underground leaching flowsheet includes Au dissolution by chlorine-containing solutions, Au adsorption from solution onto active carbon, carbon concentrate ashing and calcine melting to produce Dore metal."

Jan 1, 2003

By Chen Zhiqiang, Luo Chuansheng, Chen Ziqiang, Liu Jianguo, Rao Jinshan

To comprehensively utilize the valuable resource in tailings, increase the economic benefit of mine, reduce the amount of tailings, prolong the service life of tailing dam, the comprehensive utilization of tailing resource is arousing the attention of more and more mines. Research of comprehensive recovery of feldspar and silica from Cu-Mo floatation tailings has been furthered. Technology of "De-sliming-Magnetic Separation-Reverse Flotation-Feldspar and Silica Separation" has been developed to utilize the resource. Slime is removed and reagents cost is reduced by de-sliming. The specific effective collector ZL is used in gangues reverse flotation, and GZ-818 is the collector in feldspar and silica separation. The grinding operation is vital to ensure the liberation degree of feldspar and to eliminate the reagents pollution on minerals surface. To a Cu-Mo flotation tailing assaying K2O 5.22%, Na2O 2.22%, Fe2O3 1.95%, Al2O3 12.05%, SiO270.66%, superfine K-feldspar and silica concentrates can be produced. The feldspar concentrate productivity is 29.67% assaying K2O 8.99%, Na2O 2.86%, Fe2O3 0.16%, Al2O3 16.99% and SiO2 68.92%. The silica concentrate productivity is 14.20% assaying 0.17% K2O, 0.04% Na2O, 0.01% Fe2O3, 0.55% Al2O3 and 98.17% SiO2. The technology provides technological reference model for the similar mines.

Jan 1, 2014

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

By Hakan Gürsoy, Kemal Bilir, Bahri Öteyaka, Ali Uçar, Oktay Sahbaz

"Jet diffuser flotation column (JDFC) is a flotation device resembles Jameson flotation cell (JFC) in terms of operational principles, but it has significant difference structural points of view. This difference is an essential change in the downcomer to provide an increase of performance of the cell for the coarse particles. By using the hydrodynamic and fluid mechanics principles (Sahbaz et al., 2013) downcomer was changed as a diffuser, therefore turbulence at the end of the downcomer was reduced to provide better aggregate stability and homogeneous dissipation of the bubbles in the separation tank. According to experimental results carried out in pilot scale JDFC, not only higher flotation performance comparing with Jameson cell was obtained specifically for coarse talc particles in a certain condition, but also quiescent froth layer was acquired. In these tests, vertical pipe of JDFC having inlet diameter of 6 cm and outlet diameter of 11.5 cm was used with separation tank having the diameter of 39 cm. By using the data, pilot scale JDFC having 410 cm vertical pipe integrated with separation tank was produced and flotation tests were carried out by using the naturally hydrophobic mineral (talc). Finally, the talc recovery obtained as 94% by the use of JDFC, while Jameson cell has the recovery of 77% for the particle size of 250 µm."

Jan 1, 2014

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By Kirsten Corin, Margreth Tadie, Michael Nicol, Cyril O’Connor, Jenny Wiese

"The recovery of base metal sulfides has been emphasized in the study of the flotation of platinum group minerals (PGMs). However, in some ore bodies such as the Platreef of the Bushveld Complex, sulfide minerals do not make up the majority of the more significant PGM mineralization. It is therefore important to develop a fundamental understanding of how non-sulfide and sulfide PGMs respond respectively to the current reagents being used in the flotation of these minerals. The interactions between platinum and palladium sulfides and tellurides with the thiol collectors, ethyl xanthate and diethyl dithiophosphate, have been studied using the electrochemical techniques of mineral rest potential and voltammetry measurements. The differences in the interaction between the two types of minerals with these reagents were of key interest. Rest potential measurements indicated stronger electrochemical interactions of the minerals with ethyl xanthate than diethyl dithiophosphate. These measurements also indicated that there are different forms of oxidized collector present on the mineral surfaces after interaction with ethyl xanthates. Voltammetry measurements support these observations and suggest differences of adsorption on Pt and Pd sulfides than on Pt and Pd tellurides. Voltammetry also showed that there was minimal electrochemical interaction between the Pt and Pd minerals and diethyl dithiophosphate."

Jan 1, 2014

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980.s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão - GO), Bunge (Cajati - SP), Fosfértil (Tapira - MG) and Copebrás (Catalão - GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By Aubrey Mainza, Malcolm S. Powell

"A hydrocyclone with two vortex finders, named the three-product cyclone, has been successfully tested in the Platinum industry for dealing with the dense chromite found in UG2 ores. This dense component preferentially reports to the cyclone underflow, resulting in an over-ground fine chromite component in the final product. The dense media effect caused by a high chromite concentration in the cyclone feed produces a coarsening of the cyclone overflow, which results in loss of recovery through over-size material in the float feed. The fine barren particles of chromite that report to the overflow are recovered through entrainment in the flotation process, resulting in detrimental contamination of the slag produced from the concentrate.With the three-product cyclone a middlings product has been extracted that has a higher concentration of fine chromite. This volumetric stream flow represents a small percentage of the total cyclone feed and it is thus possible to treat it separately via fine screening to remove the fine chromite from the system and recover coarse silica."

Jan 1, 2003

By M. S. Eygi

This study covers the investigations based on the electrokinetic and rheological properties to explain the interactions between kaolin minerals and commercially available polyelectrolyte in anionic character. Additional adsorption test were also conducted to support the interaction mechanism. Adsorption tests showed that adsorption densities decrease by increasing the solid content. In-creasing the solids contents from 1% to 30% by weight resulted in the decrease on adsorption from 2.14 mg/g to 1.85 mg/g. Because of its difficulty, the solids ratio at 70% was not studied. However, following to trend of the curve plotted adsorption density-solid ratio, an estimation was made and adsorption density at 70% solid content was extracted from the curve as 1.75~1.80 mg/g. The electrokinetic studies pointed out that the presence of polyelectrolyte increase the zeta potential of kaolin from 40 mV to 60 mV which is reasonable conditions to disperse and stabilize the kaolin slurry and lower the viscosity. When these result of the different tests are combined and considered together, 2 mg/g polyelectrolyte concentration was noted as optimal concentration where adsorption density, viscosity and zeta potential of the slurries give maxima and remain constant after this concentration.

Jan 1, 2014

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By Alex Heath, Andrew Barycki, Baladron. Javier

"Efficient flocculation is important to thickener performance, affecting the overflow clarity, solids settling flux, underflow density and operability. Many factors affect flocculation; from the material/flocculant type, dilution of the feed and flocculant solution, mixing, to the shear rate and shear history. The flocculant addition point (or points) can be used as a tuning method to alter the effective flocculation time in a feedwell, with addition further up the feed pipe increasing the residence time but making the aggregates more prone to breakup if they experience high shear later in the process. Conversely, adding the flocculant later, eg under the feedwell shelf decreases the mixing time but allows some free (unadsorbed) flocculant to be available at the feedwell exit. An extensive trial has been performed on an operating thickener comparing seven individual different flocculant dosing positions through a Vane feedwell, and some combinations of two dosing points simultaneously. Measurements of the velocity, solids concentration and aggregate size were made throughout the feedwell at the different positions, with the dosing points significantly changing the aggregate size and clarity, and also affecting the solids concentration at some positions. The results are accessed in terms of flocculation kinetics and used as CFD validation data."

Jan 1, 2014

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By Daniela Campos, Aldo Casali, Gonzalo Montes-Atenas

The understanding of the effect of the major variables influencing the froth flotation performance may allow both to predict and to identify best operating conditions towards optimizing the process efficiency. The aim of this research work is to model the effect of dissolved oxygen onto froth flotation performance. Experimental pilot plant results were obtained from a continuous circuit consisting of a ball mill and a rougher bank of four flotation cells. A series of flotation experiments were run with different conditions of dissolved oxygen keeping constant most of other operating conditions. Variables difficult to control were measured or estimated. A set of mathematical models suggested in the published literature were tested. It was found that the copper recovery results were highly sensitive to the concentration of dissolved oxygen. The latter confirmed the reactions mechanisms associated to the collecting capabilities of current flotation reagents used in the flotation of copper sulfide ores. On the contrary, the results of molybdenum recovery varied non-linearly with changes in dissolved oxygen which could not be explained directly in terms of the computed specific rate constants. The error analysis confirmed that Klimpel continuous model exhibited the best specific rate constant correlation with molybdenum recovery data. Lastly, the classic particle force balance equations indicated that the adjustments of estimated mineral liberation with experimental data exhibited a turning point when passing from highly liberated to low liberated particles. The values of recovery for such turning point correlated well with the concentration of dissolved oxygen. The results indicated corrections due to changes in the dissolved oxygen must be incorporated in future froth flotation descriptions.

Jan 1, 2014

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By M. Canbazoglu

In this study, optimum sulphuric acid leaching parameters of zinc and other valuable metals from two different waelz clinker samples were researched. Origins of the samples are electric arc furnace dust and original non-sulphite zinc ore waelz clinkers. The main zinc mineral determined as zincite in these samples. Collective dissolution of zinc and other valuable metals in waelz clinkers can easily achieved by sulphuric acid leaching of them. 96% of zinc can be dissolved at 80 ºC, 60 g/L sulphuric acid concentration, 60 min. leaching time and 1/5 solid/liquid ratio. Almost 90% of Cd, Cu and Co in clinker dissolved at these conditions while dissolution of Fe was almost 20%. The consumed acid amount for dissolved per ton of zinc is approximately 1.7 tons at these conditions.

Jan 1, 2014

By Robert Peretti, Antonio Zucca, Andrea Manni, Silvia Serranti, Paolo Massacci, Marcello Ghiani

"This research study aims to identify the best way of processing colemanite concentrates, which is sometimes characterised by a high content of As sulphides, finely disseminated in the matrix of the boron mineral.Scanning Electron Microscopy analyses have been carried out to identify all the mineralogical constituents and to evaluate their distribution, frequency and mutual relationships.Colemanite concentrates are mainly used by chemical plants producing boric acid and gypsum. A high As content is unacceptable for further use of tailings coming from the leaching process and is very dangerous if the tailings are released into the environment.Grinding tests were conducted under dry and wet conditions in order to assess how As sulphide minerals are released from colemanite minerals.Some of the difficulties involved in obtaining selective liberation of As sulphides from colemanite minerals were overcome, although a certain decrease in As grade in the higher size classes was registered.All comminution products have been analysed by SEM, monitoring the degree of liberation of the mineralogical constituents.Flotation tests have been carried out, following different comminution flow sheets and adopting different modulating conditions in order to evaluate the influence of the following parameters:- collector concentration versus contaminants concentration (As minerals) in the froths;- kind and quantity of the frothing agent to maximise mineral recovery in the froths;- kind and quantity of the modulating agents to maximise the selectivity of the process;- conditioning modalities in order to obtain a suitable dispersion of fines and avoid segregation of Asbearing particles together with colemanite ones;- solid/liquid ratio of the pulp to minimise the water flow into the plant.Information obtained from SEM analysis has been adopted to evaluate segregation phenomena in pulp and in flotation products."

Jan 1, 2003

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003