Search Documents

By N. Naude, W. P. Roux

"Traditionally minerals processing equipment, such as jigs, are studied by characterising the feed and products from these processes. With this approach important details on the mechanisms of a process can be overlooked since assumptions have to be made on the internal operations of the equipment. Positron Emission Particle Tracking (PEPT) is a non-invasive technique that can be used to track a particle’s movement inside a closed vessel. PEPT makes it possible to observe the inner workings of a process, providing new information that was unattainable only a few years ago. Jigging has long been considered as one of the most difficult mineral processing techniques to model, due to the complexity of the mechanisms contributing to the separation of minerals during the jigging process. In this investigation PEPT was used to study the particle flow inside a laboratory batch jig. The aim was to determine if the particle trajectories could provide new insight into the jigging and its mechanisms. Three dimensional particle trajectories were observed with spatial and temporal resolution high enough to see details of the individual pulses during jigging. It was found that the pulse height is very dependent on the position in the jig bed. The vertical component from the trajectories showed the rate at which particles move through the jig bed (stratification rate) and it was seen that the density of a particle affects the stratification rate more that the particle’s size and that the shape in the range that was tested had little to no influence. Other phenomena such as a circular flow pattern was observed inside the jig and it was found that smaller lower density particles are affected by this circular flow pattern which tend to disperse these particles throughout the jig bed. Visualising the flow inside a jig by means of PEPT has shown to be instrumental in the deeper understanding of the process."

Jan 1, 2018

By Peter Ay, Harry Pempel, Satya Narra, Mike Müller, Jens Markowski

"Within the next few years major changes in mobility are expected. Increasing numbers of electric powered cars, electrobikes and E-Scooters define the transport sector. Recently lithium based traction batteries as storage medium have led into matrurity of series production combining high electrical efficiencies with low weights and compact dimensions. Due to the relatively young development with lithium batteries utilization, only few investigation were conducted regarding their recycling. Conventional battery recycling processes can not be applied due to differences in design and chemistry. So an automated disassembly and processing procedure for lithium traction batteries has been developed in the R/D-project ""Li-WERT"". Instead of complete smelting of the batteries without pretreatment, an automated disassembly and specific treatment of the material streams was realised, adjusted to the needs of the subsequent recovery technologies. A higher quality, with reduced expenses for the separation of fine-grained or fused material mixes, can be obtained for the individual components. The automated disassembly using an industrial robot significantly reduces dangers for the operating crew. The selective disassembly and beneficiation allows full recovery of the fractions. The batteries will be disassembled to cell level by the industrial robot. Anodes, cathodes, and separation layers are isolated and processed. The technology is designed, that no waste is generated for disposal. The pelletised cathode coating and the other separated metals (stainless steel, copper, aluminum) can be used in respective metallurgical plants. Circuit boards and plug contacts are also coveted secondary raw materials for reuse. The process is modular and offers high flexibility, e. g. for new battery types/ sizes by quick adjustment of the robot and tool change. Adaptation to other cathode materials (e. g. Li[FePO]) is possible. After finishing the R/D-project, a pilot plant for demontage was realised in 2013."

Jan 1, 2014

By S. Schade-Dannewitz

In terms of a sustainable waste management, high recycling rates and purities of the different collected waste components are very important. Especially the recycling of used packaging materials with valuable components like plastics, ferrous and non-ferrous metals and liquid cartons (light weight packaging) requires a complex technology. In plants to recycle those light weight packaging materials films cause problems and often manual sorting is necessary to remove them. The Nordhausen University of Applied Sciences together with the company Schulz & Berger from Altenburg tries to replace manual sorting with fully automated technologies. The objective is a technology that can enable a high recovery of recyclable film and satisfy the maximum purity requirements for the film fraction. For that purpose, a new machine called Low-pressure Separator was developed. The test materials used consist of separately collected recyclables from the yellow recycling bins or bags in Germany?s Dual System (Duales System Deutschland ? DSD), the recyclable waste collection system. First tests show that high purities of the film-fraction, for example the required 92% or higher, can be realized. Next to the film-purity, furthermore the mass yield and the recyclable yield are discussed because they play an important role to evaluate the efficiency of the recycling process. Further activities to improve and establish the developed technology are mentioned.

Sep 1, 2012

By D. Bastin, J. Frenay, J. Dassas

"The Luiswishi deposit belongs to the Cu-Co deposits of the Southern Group of the Katangian Copper Belt and is operated by a joint venture between EGMF (Entreprises Générales Malta Forrest) and Gecamines (Générale des Carrières et des Mines). The Cu-Co ore is beneficiated by the sulphidization process at the NCK (New Concentrator of Kipushi) at Kipushi.Sulphidization followed by flotation with sulphydryl collectors is a common practice for the treatment of oxidized base metals ores. This process is complex and its application at the industrial scale is quite sensitive. In Central Africa it is also a cost intensive treatment as the sulphidizing agent has to be imported. In order to improve the metallurgical performances and to optimise the economics of the process, a laboratory research program was carried out by the Laboratory of Metallurgy and Mineral Processing (MTM) of the University of Liège in close collaboration with EGMF and Gecamines. This program included the study of various flotation reagents as dispersing, depressing and activating agents.This paper presents the results obtained with the use of ammonium sulphate as activator of the sulphidized xanthate flotation. Although ammonium sulphate has been mentioned in the literature as a promoting agent of the sulphidized xanthate flotation of malachite, its effects on the flotation of cobalt oxides was not known.The testworks were carried out on various oxidized siliceous ore types from the Luiswishi deposit. A 1.7 l Agitair laboratory flotation cell was used. NaHS and potassium amylxanthate were respectively choosen as sulphidizer and collector. A mixture of gasoil and tall oil (90/10) was used as secondary collector. A multistage sulphidization was realised. Values of pH were followed during the different tests and an ion selective electrode Ag/Ag2S was used to control the Es potentiel evolution during the stepwise addition of the sulphidizer."

Jan 1, 2003

By M. Morales, J. Yianatos

"In this work, an alternative approach to evaluate the flotation performance along a flotation rougher row is presented. The collection zone as well as the froth zone performances were separately evaluated. For this purpose, sampling for metallurgical balances along with sampling of top-of-froth (TOF) grades in each cell of a flotation row were employed. The modelling of the rougher circuit consisted of using TOF grades for evaluating the collection zone recovery, because they are a good representation of the bubble loading, which identifies the true flotation process, as shown in previous studies for shallow froths. In addition, the feed characterization, size-by-liberation, allowed the identification of the mineral distribution and its evolution along the circuit. The latter result was obtained by fitting the recovery profiles as well as the TOF grades down the flotation bank. The flotation rates and the maximum recoveries in terms of size-by-liberation (size classes: -45 µm, +45-150 µm, +150 µm, and liberation classes: -20%, +20%-80%, +80%) were then estimated. The results were in good agreement with those reported in literature by other authors and showed the new approach allows flotation kinetics to be characterized in industrial circuits.INTRODUCTIONMineral recovery in industrial flotation circuits is a function of the mineral characteristics, such as particle size distribution and liberation (Trahar, 1981, Jameson, 2012), and operating conditions such as air flowrate, pulp flowrate, solids percent and reagent conditioning (Jameson 1977; Klimpel, 1980; Mehrotra and Kapur, 1974). The cell type and size (self-aerated or forced air) and the circuit arrangement (single cells or banks of cells in series) are also relevant factors. Sampling of circuits (e.g. rougher, cleaner or scavenger) are commonly carried out using standard automatic samplers for metallurgical balance assessment. However, the flotation plants are generally not provided with proper accesses for local streams, which hinders the recovery estimations and the flotation rate characterization."

Jan 1, 2018

By X. H. Zhou

Column flotation is being widely adopted for fine particle treatment by the mineral processing industry due to its simplicity of structure, high efficiency and good separation performance. Cyclonic static micro-bubble column flotation (FCSMC) is an innovative column separation technology that has been successfully applied in the coal preparation industry in China. Recently, the application of this equipment has been further expanded to the separation of several minerals such as fluorite, copper, iron, etc. The bottom of the FCSMC is a cone in which cyclonic field is generated when circulating pump is injected tangentially into the column. The unique cyclonic structure is believed to help enhance the column separation performance. Since the FCSMC is a new flotation device, little work has been done to understand the fundamentals of this technology. In this research, a computational fluid dynamics software, ANSYS/ FLOTRAN, was employed to simulate the flow field of a lab FCSMC system (F0.2 m, F3.0 m by length.) The distribution patterns for velocity field and flow field were investigated under single phase condition. It has been found that axial velocity of the slurry decreases and becomes stable along the height of the column from bottom to top, and the slurry performs as a descending flow pattern. Another observation is the velocity fluctuates vigorously near the wall due to wall effect. Compared to axial velocity, the radial velocity distribution is smaller and more complicated. The basic pattern is that on a given cross section of the column radial velocity increases from the wall to the center and it the velocity changes greatly around the center. Under the condition of column height less than 0.8 m, the axial velocity is negative and it directs from the wall to the column axis. When column height is higher than 0.8 m a reverse pattern is obtained, i.e., axial velocity is positive while directing from column axis to the wall. Special efforts were directed to investigate the tangential velocity pattern. Results indicate that the tangential velocity patterns of different cross sections are similar and showed a symmetrical distribution. Tangential velocity distribution concluded two zones: outer whirlpool and inner whirl-pool. And, interestingly, it has been found that on different cross sections the highest tangential velocity always occurs at the same position of the cross sections.

Jan 1, 2014

By A. Kurkov

Flotation process is based on the formation of primary collector-based supramolecular associates at the mineral surface and within the pulp. Supra molecular chemistry allows studying within a common framework, all kinds of molecular associates, from dimers to large assemblies, resulting from spontaneous association of a large number of interacting components of the flotation system, where the collective action of non covalent bonds can have an important role. Self-organization of supra molecular assemblies in the flotation process can be controlled by modifying the chemical structure of the collector, the nature and arrangement of functional group in it, by introducing secondary agents (SA) into the process, to adjust the interaction between the collector and the surface and to control the hydrophobicity of the adsorption bed. This offers broad opportunities to build supramolecular assemblies to improve the efficiency of flotation. Besides, the more complex is the system, the weaker are the interactions, that determine its behavior. This powerful factor still is not employed deliberately to control the flotation process. Organophosphorus compounds (OPC) - dialkyl phosphoric acids whose radicals contain ethoxylated groups ? are considered as nanocompounds, that can be used in building supramolecular assemblies. The presence in an OPC molecule of functional groups (P=O, P (O) O-, P (O) OH), ethoxylated groups, and aromatic rings is the basis for the formation of stable supramolecular associates. Gross formula: C54H94KO16P. Molecular weight is 1069.39. Phosphoryl anion has a regular tetrahedral structure with the angle of 109.5°. Lengths of -P-O- bonds in a PN molecule are 1.7345Å; length of the hydrocarbonic radical C42-C72 = 33.942Å. In an alkaline environment, PN is in the form of the anion, in an acidic environment ? in the form of the polycation due to protonation of the oxygen in the EO group. Chem Office software suite was used to generate three-dimensional images of an OPC molecule in acidic and alkaline environments, to reveal the OPC geometry (bond lengths, valence angles, aliphatic radical length), to identify the collector's binding sites with the mineral surface, to find the most stable and energy-efficient molecular conformations of an OPC molecule and its complexes with minerals under various conditions. Mechanisms of interaction between OPCs and the mineral surfaces are different. In ores whose minerals are dominated by ionic bonds (fluorite), the interaction mainly involves the anionic form of the collector; in ores, whose minerals are dominated by covalent bonds - the oxygen of the phosphoryl group (donor-acceptor interaction) and the oxygen of the ethoxylated groups. This difference is responsible for the formation of spatial associates with different surface layer structures. Introduction of supramolecular chemistry concepts into the analysis of flotation phenomena and mechanisms can become an effective tool for better understanding the flotation process and offers new means of consistently improving its effectiveness.

Sep 1, 2012

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By M. R. Robben

Carbonates have gained significant economic importance for the human kind. On one hand over a hundred uses are listed for carbonates. On the other hand, carbonates host base metal deposits. Although the carbonates play a significant part in the development of those deposits, in the mineral processing they consume acid and cause selectivity problems during flotation and leaching. Carbonates also accompany other industrial minerals as waste rock. For all those cases it necessary to find a technique to separate carbonate as early as possible in the processing chain. In this paper, the applicability of near-infrared spectroscopy (NIRS) sorting for the separation of carbonates is discussed. NIRS sorting is a sensor-based sorting technique, in which particles are singularly detected by a sensor and then rejected by an amplified mechanical, hydraulic or pneumatic process. This technique can for example be implemented in the process as a pre-concentration step for coarse particle sizes up to 300 mm. NIRS sorting discriminates among materials based on the difference that exist between their spectral properties in the near-infrared (NIR). Vibrations of molecular bonds in carbonates cause characteristic spectral properties in the NIR, which makes carbonates detectable, possible to identify, distinguish and separate from other rock materials. The spectral properties can also be used to distinguish between different carbonate minerals and mixtures. If the spectral variations are large enough for detection, sorting based on NIRS is possible. Feasibility studies on sensor-based separation of carbonates in the processing of talc, borate, fluorite, marble, zinc-oxides, copper sulphide and iron ore as well as the discrimination of calcite and dolomite mixtures are conducted and indicate the high potential of NIRS sorting in the minerals industry. Keywords: carbonate separation, sensor-based sorting, near infrared spectroscopy, NIRS sorting

Sep 1, 2012

By J. Yianatos

The cleaning circuit operation and its effect on the plant metallurgical performance, was characterized at Los Pelambres concentrator, Chile. Experimental data from columns, scavenger and regrinding stages was evaluated. Each stage was characterized by size fractions, and the interaction between stages (columns, scavenger, regrinding) as well as the effect that circulating loads had. The approach for describing the flotation equipment operation (cells and columns) considered the collection and froth zones separately. This methodology allows for the identification of the impact that particle size distribution has on the actual collection and froth transport processes, independently. In this way the effect of regrinding on flotation recovery and grade can be related to the corresponding operating variables, e.g. pulp flowrate, air flowrate, pulp level and pulp density, among others. The effect of gangue entrainment was considered using an empirical dimensionless correlation. The interaction between the circulating load and the overall performance of cleaning circuit was evaluated. The circulating load was defined as the ratio between the solid flowrate of scavenger concentrate over rougher concentrate. It was found that the overall cleaning flotation circuit (column-scavenger) can operate at a relatively high and constant recovery for a wide range of mineral treatment. This is possible when the scavenger has the capacity for compensating the decrease in column recovery at larger circulating loads. Under the condition of high overall cleaning recovery, the rougher stage closely represents the plant recovery. However, at large mineral treatment conditions, the design characteristics (e.g. concentrate transport channel capacity and transfer boxes) as well as instrumentation, control facilities and operation, became bottle-necked. A simulator was developed using empirical models for each stage (column, scavenger and regrinding) in order to evaluate proper operational strategies for cleaning flotation circuits Keywords: flotation, cleaning, regrinding, Vertimill, simulation.

Sep 1, 2012

By l. Bokányi

The Tóth adsorption isotherm-model was derived and has been widely used for the inhomogeneous solid surfaces. The three-parameter isotherm incorporates the effect of the interaction between the adsorbed substances as well. All classic isotherms can be clearly derived from this one. Bio sorption is the sequestering of dissolved components, i.e. metals from aqueous environment by living or dead biomass. The mechanism of the bio sorption is rather complex and predominantly refers to the affinity of the chemical functional groups: acetoamido groups of chitin, structural polysaccharides, amino and phosphate groups in nucleic acids, amino, amido sulfhydryl and carboxyl groups in proteins, hydroxyls in polysaccharides, sulphates, etc. towards the soluted substances, i.e. heavy metal ions. The physisorption, as well as the micro precipitation also play a role in the bio sorption mechanism. The description of such a complex process can be done by a model reflecting this complexity. According to our experimental results obtained using algae and immobilised algae for the sorption of heavy metal cations, the most appropriate model for such a description is the Tóth-isotherm, the parameters of which can be interpreted. Flotation process is also a very complex one, the overall result of which depends on the partial results of many micro processes and parameters. The particle interaction which very often takes place in the flotation systems makes the phenomenon even more complex. The flotation kinetic model with particle interaction was already introduced by author in 1994 and further developed in 2000. In this paper based on the experimental results obtained with metallic particles in case of recycling flotation the applicability of the Tóth-equation as an alternative flotation kinetic model for the systems with particle interaction is proved. The applicability of Tóth-model in mineral processing demonstrates again its universal character and the great talent of the late József Tóth, great Hungarian chemist. Keywords : Toth isotherm, biosorption, Langmuir, Freundlich

Sep 1, 2012

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By P. Basarova

The attachment of bubbles onto a collecting surface is an ubiquitous natural phenomenon, playing a critical role in numerous practical processes. The goal of the project is to broaden the knowledge about hydrodynamic interactions between small bubbles and large solids that occur in nature and industrial processes. Focusing on collision processes between a single rising bubble (Db<1 mm) and a larger falling spherical particle in stagnant liquid, the theoretical model describing the bubble trajectory is given here. The model is based on analysis of forces acting on the bubble, and utilizes equation for the bubble motion. Mobile and immobile type of bubble surface mobility are considered. The calculated results are compared with the experimental data; here a high-speed video camera was used to capture the bubble motion and bubble-particle interaction. Very good agreement between experimental and calculated data was found. For both types of surface mobilities, the bubble deviation in the horizontal direction is nearly linear. The proportion constant is bigger for immobile bubble surface and increases with the bubble size. Furthermore, particular forces acting on bubble were studied. A similar course of relative bubble velocity and force impact was observed for identical bubble position. For cases when the bubble centre is close to the particle axis, only deflection in one direction is observed. When the bubble is reaching the maximum trajectory, the force ratio is changed. The bubble is firstly pushed away from the particle, but when it is within close distance from the particle, the bubble is pushed towards the particle.

Sep 1, 2012

By C. L. Lin

Previous research on particle damage during high pressure grinding roll (HPGR) crushing was limited by the resolution of point-projection micro CT systems and the extent of damage was described by the percent of particles cracked for different crushing methods as determined at a voxel resolution of 40 microns. With recent advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. With the use of X-ray lens imaging the resolution is determined by the lens rather than by the spot size of the micro-focus X-ray source. The high resolution X-ray micro CT (HRXMT) system made by Xradia with a voxel resolution of less than 1 micron is now being used for the characterization of particle damage during HPGR crushing. In this way, the direct 3-D determination of the internal damage of crushed ore particles which vary from 40 mm down to 100 microns in size is being studied at a voxel resolution of a few microns. The number, size, and shape of cracks can now be measured at this improved resolution and for the first time the specific crack surface area distributions of the crushed product can be calculated from HRXMT images using specially designed software tools for 3D analysis. Results from selected crushing operations are presented. Copper ore particles from HPGR crushing at high pressure (6 N/mm2) are severely damaged having crack specific surface areas as great as 10 mm2/mm3. Keywords: HPGR, particle damage, X-ray micro tomography, crack surface area

Sep 1, 2012

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By Anatoly Usov

The detailed researches of a broad circle of problems connected to development of the electric pulse method destruction materials (EPD) of a various nature and area of use are executed. The electrical and power characteristics of process, physical fundamentals of selectivity of a breakdown and destruction are investigated, the device of electric pulse (EP) disaggregation and ?omminution of materials are developed, the technological efficiency of disintegration of industrial minerals estimated. Due to its technological advantages, the EPD could have a great potential in minerals mining and processing technologies. Low specific power and weight-and-size characteristics of EP installations based on the existing out-of-date electric equipment are at present the main reasons hindering the effective application of the method in mining and processing technologies. The main studies carried out in Russia in the field of electro technical equipment development for EP technology are presented. The pulse capacitors service life affects greatly the economic efficiency of the process because the capacitors cost accounts for a considerable, and in some cases, the most part of the operational costs. Determined and analyzed in the study are the ways which could significantly improve the specific characteristics of high voltage pulse generators (VPG), such as to use of high-frequency voltage transformation to develop a charger; to use pulse transformers (PT) with iron magnetic circuits made of materials characterized by high magnetic permeability, in pulse generating circuits; as well as to use special ways which could produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for EP devices, and a further strategy of the EP technologies development and application has been suggested on this base. Keywords: electric pulse disaggregation, electric pulse installation, charger battery, high voltage pulse generator

Sep 1, 2012

By T. B. M. Himawan

In this study, effect of thiosulphate and oxidation using oxygen were studied in arseno copper ore flotation. Single mineral study of chalcopyrite and tennantite in regard to the aforementioned techniques was also studied. Zeta potential, XPS, contact angle and floatability of single minerals were conducted for each treatment to understand the mechanism. It was revealed that the separation is best conducted in alkaline condition at where there will be interaction between thiosulphate and the mineral surface as well as the formation of hydroxide species in the oxidation using oxygen. From zeta potential of both thiosulphate and oxidation conditioning, it can be found that the reactivity of tennantite is much higher rather than chalcopyrite resulting higher rate of depression on both techniques as shown from contact angle and floatability of each mineral after treatment. XPS spectra confirmed qualitatively and quantitatively the existence of species responsible for the depression of each conditioning techniques. As for the copper ore flotation test, it is the oxidation using oxygen provides best performance after 60 minutes of oxidation. Keywords: tennantite, chalcopyrite, arseno copper ore A, thiosulphate, oxidation using oxygen

Sep 1, 2012

By Kaiwen Liu

Activated carbon is widely used in the removal of organic and/or inorganic contaminants from waste water due to its high surface area, porous structure, and specific surface reactivity. However, in practical applications, it is difficult to recover the activated carbon completely by screening or classification. In this project,we prepared a magnetic form of activated carbon (magnetic activated carbon or M-AC) by precipitation of iron oxides on the surface of activated carbon. The M-AC can be easily separated from effluents by applying an external magnetic field, thus it can be recycled and regenerated for reuse. M-AC was characterized by X-ray diffraction (XRD), specific surface area measurement, and scanning electron microscope (SEM).XRD results show that the major phase of coated iron oxides on activated carbon is magnetite (Fe3O4). The specific surface area of activated carbon was found to be reduced after the impregnation of magnetite particles on the surface. The SEM micrograph shows the aggregation of the iron oxides on the surface of activated carbon. M-ACwas found effective in removing DETA (diethylenetriamine) species and metal ions from solutions. Cu (II) with initial concentrations from 5 ppm to25 ppm in solution is removed by more than 99% with the addition of 0.1 wt.%ofM-AC. For the removal of 25 ppm DETA species from solution, an addition of 0.5 wt.% of M-AC is required due to the larger size of the DETA molecule. Moreover, M-AC showed a good loadingproperty for nickel and gold ions from solutions. M-ACshows a better adsorption capacityover activated carbon and its potential applications in carbon-in-pulp for gold leaching and waste water treatment. Keywords: magnetic activated carbon (M-AC),diethylenetriamine (DETA),metal ion,adsorption

Sep 1, 2012

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012