Search Documents

By W. G. Wu

More and more researches and applications of organic chelating agents as depressors or activators are carried out in the course of research and application of modern flotation. The paper puts forward the necessary condition of organic chelating agents as depressors or activators by analyzing the chelating chemical performance of organic chelating agents with metal ions and the stability of chelates formed by them; at the same time, puts forward four sufficient conditions of organic chelating agents as depressors or activators according to different hydrophilic capability of the chelates and different performance of depression and activation of organic chelating agents for minerals. Namely, the ?1+1/4? necessary and sufficient conditions of organic chelating agents as depressors or activators are put forward.

Jan 1, 2014

By J. Zou

With the increasing applications of the Chinese metal magnetic liners, the requirement for their technical specifications has become stricter and stricter. It is necessary to deeply analyse the metal magnetic liners in order to improve their reliability and economics. The key issue of metal magnetic liners is magnetic forces: their attractions to mill shell and protection layer. Mathematical models were developed using finite-element analysis software and systematic simulation analyses of the two most critical indexes of magnetic liners were performed to find out the most important parameters and their effect on the liner?s characteristics. The relationships between magnetic forces and installation gaps, thickness of permanent magnets and thickness of protection layer may be used to guide the design of metal magnetic liners for ball mills in order to achieve good economic indexes.

Jan 1, 2014

By S. J. Ma

To look into the ionic release laws of the sulphide tailings in some copper mine, the effects of the soaking period, temperature, oscillating speed, and pH of the solution on the heavy metals ionic re-lease were investigated through static soaking leaching experiments. The results show that Cu2+, Zn2+, Pb2+, Cr3+ are of different leaching behaviors with soaking period. The ionic concentration in soaking solution for four ions has a great gap. Zn2+ is more easily released out of sulfide tailings than Cu2+, Pb2+, Cr3+ , and the ion release concentrations are not proportion to their contents in the tailings. The time for each ion to reach its maximum concentration are different. The minimum concentration do not occur at the first day. Each ion concentration shows different fluctuation characteristic during soaking process. Solution pH, oscillating speed, and temperature affect the releases of Cu2+, Zn2+, Pb2+, Cr3+ out of the tailings to different extent. The effect of pH value on ion re-lease for the four ions ranks as Zn2+>Cu2+>Pb2+>Cr3+, the oscillating speed ranks as Pb2+>Zn2+>Cu2+>Cr3+, and the temperature ranks as Cr3+>Pb2+>Zn2+>Cu2+.

Jan 1, 2014

By G. Unland

The sizing of crushers depends on the expected crushing forces. However, the crushing forces develop differently with every individual rock while it is compressed by the working surfaces of the crusher. For sizing, this compression process has to be characterized by the maximum crushing force. The maximum crushing force depends on the strength, shape and size of the rock, the amount and velocity of the imposed displacement of the working surfaces of the crusher on the rock and the conditions of the contact surfaces. From experience it is known that the strength of the material and, therefore, the crushing forces depend on the size of the specimen. This dependence is the so called size effect. The determination is based on compression tests. The force development is recorded during the compression of the specimen and for every individual test the maximum force is determined. The occurring maximum crushing forces of several rocks with the same diameter comminuted under the same conditions can be assessed by a mean value and a variance. The relationship between the mean values of the cross section related maximum crushing forces FAmax and the corresponding sizes d of the specimens can then be described by mathematical functions. They are derived from different approaches (phenomenological, statistical and statistical-physical methods). The phenomenological methods are subjective and yield functions depending on the assumptions of a person, whereas the statistical and statistical-physical methods are based on an evaluated function and the optimization of the parameters.

Jan 1, 2014

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014

By Boris Albijanic, Hongjuan Chen, Bogale Tadesse

"During mechanical flotation of fine liberation sized complex rare earth ores, a large fraction of ultrafine valuable mineral particles are lost to tailings. Fine gangue mineral particles can be entrapped within the froth phase and be floated together with target mineral particles. Another common challenge in ultrafine rare earth mineral flotation is the formation of a sticky froth (excessively stable froth). Thus, the improvement of the flotation of fine and ultrafine rare earth bearing minerals through appropriate cell design and reagent selection is highly desirable. The aim of this study is to investigate the performance of a pico-bubble cavitation flotation column in improving selective recovery of ultrafine rare-earth elements (REEs) bearing minerals from complex and low-grade ores. In pico-bubble cavitation column, very small bubbles are generated which are capable of attaching to ultrafine particles and consequently modifying their surface properties. The overall effect of these processes should lead to improved flotation selectivity and recovery of ultrafine RE mineral particles. In this paper, the effects of a number of flotation operating variables on recovery and grade of REE minerals was investigated using a continuous pilot scale pico-bubble column flotation. At the flotation conditions used in this study, subtle monazite upgrade was observed while gangue Fe oxide was preferentially floated even in the presence of depressants. INTRODUCTION Rare earth elements (REEs) have unique properties such as superconductivity and catalytic activity, and are in high demand for a large number of cutting-edge technologies in the modern world including the production of mobile phones, fuel cells, displays, permanent magnets for wind power generation, high-capacity batteries, green energy devices, etc (Naumov, 2008). REEs tend to be intimately associated within many minerals, and are rarely found in high concentrations in deposits for economic extraction. Up to now, among over 250 minerals containing REEs, bastnasite (Ce), monazite (Ce, Th and La) and xenotime (Y) are the three main minerals that contain sufficient grade of REEs for commercial exploitation (Zhang and Edwards, 2012). The deposits that contain bastnäsite, monazite and xenotime usually have complicated mineral compositions, with various valuable minerals of fine embedded grain sizes in association with complex gangue minerals. In order to ensure liberation of the REEs minerals, fine grinding to less than 30 µm is necessary. This fine grinding leads to difficulty in recovering a large proportion of fine and ultrafine particles in separation processes such as flotation (Trahar and Warren, 1976). Consequently, highly liberated and ultrafine fine valuable REEs particles are lost into tailings during traditional mechanical flotation. Besides, the formation of extremely sticky and stable froth inhibits the drainage of hydrophobic particles. Thus, improving flotation of rare earth bearing minerals, particularly the ultrafine size range, is highly desirable."

Jan 1, 2018

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By J. Ma

Vanadium ore is widely distributed in black rock series (Fan, Zhang and Ye, 2004) in many provinces of China, which accounts for 87% (Zuo, Peng and Dugang, 2001) of vanadium reserves in China. In Cambrian black rock series in south Qinling Mountain, there are large or medium-sized sedimentary deposits such as Zhongcun vanadium deposit, Yinhua vanadium deposit, Qianjiaping vanadium deposit, Xiajiadian gold-vanadium deposit and Lengshuigou vanadium deposit. The vanadium is distributed in other minerals mainly in the form of isomorphic replacement. These types of ore are characterized by no independent vanadium mineral, low grade and vast reserves. Now in China the vanadium extraction technology is backward with low utilization rate of resources. The difficulties of vanadium extraction from black rock series are that the enrichment by means of mechanical beneficiation is difficult; the cost of direct chemical extraction is high and the emission of waste gas from pyrogenic process does not conform to environmental protection standard. Therefore the study of vanadium occurrence, the improvement & optimization of vanadium extraction technology and the realization of pollution-free and low-cost extraction of vanadium from black rock series are of great and realistic importance for environment-friendly exploitation & utilization of vanadium resource in China. The study is based on carbon content in ore of Cambrian black rock series in south Qinling Mountain. Two kinds of ore are selected. Vanadium ore with low carbon content (TC<1%) is taken as Sample 1 while vanadium ore with high carbon content (TC>10%) as Sample 2. Based on analysis of ore?s lithologic features and vanadium?s occurrence, a vanadium extraction technological process characterized by selective grinding, low cost and no pollution is proposed.

Jan 1, 2014

By J. K. Wen

The Mojiang nickel deposit is situated in Mojiang county, yunnan province, a tropical area in the southwestern China. The known geological resource (measured and inferred) includes 4 million tons of nickel sulphide ore at an average grade of 0.50% Ni and 0.34% As. Nickel minerals are mainly gersdorffite (NiAsS), millerite(NiS), morenosite (NiSO4?7H2O), and more than 50% nickel minerals is gersdorffite which contains arsenic. Pyrite is the dominant sulfide mineral, 22% in the ore and part of nickel minerals are locked in pyrite. It is difficult to attain the nickel concentrate quality allowed by a smelter and the acceptable nickel recovery through flotation due to the high arsenic in the ore and the nickel minerals locked in pyrite. The shake flask tests and column tests for nickel recovery from the Mojiang nickel sulfide ore had been finished by the end of 2003. The column bioleaching tests were carried out using the columns with diameter of 120 mm and height of 1200 mm, and 70% of nickel dissolution was attained in 300 days. A 10,000t pilot test heap was built in the Mojiang Nickel Mine by June 2003. The ore used in the test heap was supplied from the underground mine and was crushed to -20 mm before being feeding to the test heap, which is 4~5 m high, 30 m wide and 50 m long. The naturally adapted mesophile and moderate thermophile have been inoculated into the leaching pile by June 2003. The operating temperature in the heap ranges from 38? to 55?, varying with season. 30% of nickel dissolution was achieved in 3 months and the typical pregnant leach so-lution (PLS) contains 2~3 g/L Ni and 20~30 g/L Fe. The Ni sulfide which was produced by us-ing Na2S 10 t/t?Ni contains 16%~20% Ni and Ni recovery was 98%. 70% of Ni dissolution is expected in 12 months. The test heap was scaled up to 60,000 t of ore per year by mid of 2005. In this paper metallurgical studies and performance of the pilot test heap will be described. The results of mineralogy, shake flask tests and column tests on bioleaching of the nickel sulfide ore are reviewed. The key test heap operation parameters, the performance of bio-heap leahing-Na2S precipitation, ferrous oxidation-ferric precipitation-Na2CO3 precipitation, bacteria in the pile, water and acid balance, effluent disposal, capital and operation costs are also discussed.

Jan 1, 2014

By Alejandro Yañez, Martta Nousiainen, Rodrigo Grau

"Gas dispersion plays a fundamental role in froth flotation. Gas dispersion in flotation is quantified by using four properties: gas velocity, bubble size, gas hold-up and bubble surface area flux. Gas dispersion measurements were conducted in three flotation cells: TankCell 1, TankCell e300 and TankCell e500. The measurements reported in this paper were carried out exclusively in two-phase systems using only water and air at frother dosages exceeding the Critical Coalescence Concentration (CCC) in order to prevent bubbles from coalescing. The measurements conducted in TankCell 1 and TankCell e500 were conducted by Outotec specialists, whereas the characterization of TankCell e300 had been conducted earlier in 2008 by a team from McGill University. When working in two-phase systems and under non-coalescing conditions, gas dispersion characteristics measured in different scales can be compared directly. The measurements conducted in TankCell e300 are taken as a base line in order to compare the performance of TankCell e500, whereas TankCell 1 is a pilot-scale flotation cell which is used in rotor testing. The gas dispersion properties in TankCells were found to be affected by the air flow rate and rotor tip speed. Bubble sizes (d32) measured on the three-size scale seem to be within the same range of 0.6 mm to 1.6 mm. It was noted that the bubble size was influenced by rotor tip speed and gas velocity. In general, as the rotor tip speed increased, the bubble size decreased and as the gas velocity increased, so did the bubble size. The rotor tip speed also has an impact on the hold-up; in general, as the rotor tip speed increased the gas hold-up also increased but the influence of air flow rate on gas hold-up was greater. Bubble surface area flux was found to vary between 40 and 85 1/s. As the gas velocity increased, the bubble surface area flux also increased."

Jan 1, 2014

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By X. L. Wang

Hydrothermal method was applied in the preparation of calcium sulfate whiskers in airtight re-actor using gypsum as primary materials. The optimum conditions of preparation are as follows: pH value 9.8~10.1, concentration 5%, material size 18.1µm, which were determined by the analysis of the diameter of CaSO4 whiskers through SEM. On these conditions a product of ultrafine CaSO4 whiskers with diameter of 0.19µm and aspect ratio of 98 is obtained. Ultrafine CaSO4 whiskers with different concentrations, modified by titanate NDZ-401, were added into polypropylene as intensifier and composites of Ultrafine CaSO4 whiskers/ polypropylene were prepared by melting-extruding method. Mechanical performance of the composites was tested and surface morphology of the composites was observed by SEM. The results indicated that impact notched izod of the composites was enhanced by 49.5% compared with pure polypropylene when 10.0% Ultrafine CaSO4 whiskers were added into polypropylene and toughening effect was very remarkable. Dispersion behaviour and interface phenomenon of Ultrafine CaSO4 whiskers in polypropylene matrix were investigated by SEM. The results indicated that Dispersion performance of Ultrafine CaSO4 whiskers modified by titanate NDZ-401 in polypropylene matrix is good, which improved mechanical performance of composites to some extent.

Jan 1, 2014

By Venkata S. Buddhiraju

Pelletization of iron ores involves balling on a rotating disc to produce wet pellets and induration of wet pellets on a moving grate to produce fired pellets. The quality of pellets produced and the productivity of the pelletization process depend strongly on the characteristics of the feed to the pelletization disc, especially the particle size distribution and the moisture content. The upstream processes involved in the preparation of pelletization feed include grinding, thickening and filtration of the iron ore slurry. The focus of the present work is the closed circuit wet grinding of iron ores. The circuit consists of a primary ball mill, a regrind mill and a hydrocyclone. A population balance model was developed to predict the grinding kinetics and an empirical model was fitted for the separation of fine particles from the coarse particles in the hydrocyclone. Batch grinding kinetics experiments were performed on a laboratory scale ball mill to obtain the ore breakage parameters which were subsequently used for the simulation of the industrial mills. The models were customized for the industrial operations and the effects of different process variables like feed flow rate, water flow rate, etc., on the size distribution of product from the grinding circuit were studied. Additionally, different circuit configurations were simulated to determine operating conditions that could result in the desirable product particle size distribution. The results of simulation were in close agreement with plant observations and the new circuits explored through simulation have helped in identifying potential opportunities for process optimization and control

Sep 1, 2012

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By Gideon Chitombo

"Mining is a "continuous" process of dependent breakage and materials handling stages, from the initial breakage of the in-situ rock, extraction from the pit or underground, and finally to the surface stockpile and downstream processing. Over time, underground and in-pit mining activities diverged into two separate disciplines, each using a variety of in-situ breakage techniques and surface activities, with processing techniques dependent on mineralogy or grades. This artificial separation of underground and open pit activities was exacerbated when the two became increasingly managed as separate cost centres rather than as an integrated unit. Mass mining essentially began in 1903 when metallurgist Daniel Jackling initiated the world’s first open pit, mining system at the Bingham Canyon porphyry copper deposit in Utah. The term mass mining has since been construed to mean large open pits and cave mining methods, including their variants. These methods are largely non-selective, involving the mass extraction of a deposit irrespective of the uneven distribution of grade and mineralogy. The advantages of mass mining have historically applied mostly to low grade, large scale deposits. With the depletion of mineral reserves closer to the surface, however, new deposits are deeper, lower grade and mixed with more impurities. These and other factors make extraction more difficult and costly. Mass mining is moving rapidly into a new and less certain environment where revolutionary changes are required to effectively deal with future challenges which are technical, economic and environmental (licence to operate). This keynote address presents current initiatives being considered for the next generation of both underground and surface mass mining systems in order to significantly reduce lead times and mining costs (CAPEX and OPEX), substantially increase productivity and meet license to operate requirements. The address is designed to solicit discussion on how better integration of mining and processing can become a platform for these next generation of mass mining systems and can also help the industry deal with the future challenges."

Jan 1, 2014

By Bert Huls

Already starting, new drivers will dictate how future mineral processing plants will be designed and operated. These drivers include requirements in water and energy conservation because of rising costs, larger demand for mineral and metal products as the result of a rising population, and the increasing demand from the population in general to have influence over what type of operations will be developed where. Mineral operating facilities will require processing of lower grades. To do this economically, design engineers will be influenced to introduce newer concepts, or return to older processing concepts once deemed not desirable. Our understanding of the fundamentals must be improved, and this may come from better measurement techniques and more process piloting, and will go in hand with a reduction of waste generated during the process, improved separation of minerals or product size. Process engineers will also be required to not just design according to the established 3D methodology for efficient plant installation. Already in other industries the design concept encompasses the entire range from source to product. Not only that, the design will be affected by public influence that must be illustrated prior to project execution. On the one hand, the added dimension in design may slow a project; on the other hand it may result in a blessing, and in a higher responsibility for engineering.

Jan 1, 2014

By Thomas Mütze, Anja Hirte, Ursx Peuker, Thomas Kuhn

"The comminution behavior of two ferromanganese nodules samples of the equatorial northeast Pacific has been examined as a basis for the separation of two kinds of metal-rich layers. Those layers were finely grown together during nodule formation and are one reason that the exploration of deep-sea minerals calls for the development of new mineral processing concepts. Therefore fundamental analyses of the fracture behavior have been made under compressive and impact stress. Further experiments took focus on the crushing behavior in a jaw crusher and a small scale impact crusher as well as the milling behavior in a dry vibrating mill, a wet planetary ball mill, and a wet agitated ball mill. The comminuted products were characterized by PSD, particle shape, particle density, and porosity. The experiments show a low stress resistance of the ferromanganese nodules. Compared to compressive stress, impact stress turned out to be the more effective for crushing. Both samples showed no significant difference in the comminution behaviour which makes differing mechanical treatments unnecessary. In both cases particle sizes below 1 µm were achieved by wet grinding. This particle size is necessary to separate the two kinds of metal-rich layers which is part of continuative studies."

Jan 1, 2014

By Jan Svoboda, Toyohisa Fujita

"The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation are identified, advantages of magnetic separation in comparison to other physical methods of material manipulation are discussed and reasons for failure to live up to its potential and expectations are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.Our walk through the innovation landscape in magnetic separation illustrates the enormous effort that has been expended over the years to convert a wealth of novel idea into workable techniques. Remarkable progress has been achieved and numerous successful innovations have been introduced into material treatment operations. On the other hand these techniques have experienced their fair share of failures. The reasons for these cover a wide spectrum of risks that accompany any effort to implement new technology."

Jan 1, 2003

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018