Search Documents

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

By H. Z. Kuyumcu

Associated with the development of a novel microbiological oxidation process for the conditioning of iron hydroxide slurries from ferrous mine waters, there is a realistic chance to make the contained iron available for a material utilization. The transformation of ferrous into ferric compounds is coupled with the precipitation of iron hydroxisulphate mostly in terms of the mineral Schwert-mannite. The further treatment of the iron hydroxisulphate has to be aimed on the processing for product recovery and product refinement. For many potential applications, e.g. in the ceramic industry, the pigment industry or for metallurgical applications, the removal of sulphate is essential. For the dehydration of the iron hydroxisulphate and the sulphate removal, microwave heating technology is a beneficial method. In contrast to conventional thermal heating processes the supply of energy in microwave application takes place directly within the material through the dissipation of electromagnetic energy, i.e. no heating medium is needed. It is a volumetric heating process regardless of the surface of the material. The rapid and targeted energy supply and the good controllability of microwave heating systems are advantages which have led to a wide variety of applications in industrial processes. Among the diverse use for heating of temperature-sensitive, chemical and pharmaceutical products as well as foodstuffs the number of applications also in mineral and solid processing increases. At the Department for Mechanical Process Engineering and Solids Processing of the Technical University Berlin the use of microwave technology for the treatment of iron hydroxisulphates has been investigated systematically within the framework of a cooperative research project. The paper at hand shows results from material conversion tests subject to a variation of the relevant process parameters. The reaction products are characterized and the process is compared with the conventional heating in a rotary kiln.

Jan 1, 2014

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By K. Takahashi

Generally speaking, wastewater coming from the metallurgical process for recovering precious metal contains precious metals such as gold (Au), platinum (Pt), palladium (Pd), Silver (Ag), etc., which concentration is about 10 mg/L. In addition, there are other metals such as copper (Cu), iron (Fe), which concentration varies from several mg/L to more than 10,000 mg/L. It should be noted that the concentration of metals in wastewater is relatively high, considering the fact that these metals of similar concentration can be found in ores. However, most of these valuable metals are not treated, due to the high processing cost and technical problems. Within this frame, the authors put forward a new process that includes neutralization/reduction, precipitation and fusion. The idea is to recover and recycle Au, Ag, and Pd metals as well as protecting the environment by saving the resources. It was found that this new process was able to recover more than 90% of Au, Ag and Pd.

Jan 1, 2014

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

By J. A. Sweet

The issues facing graduate training in the mineral processing industry are not too different today from those that prompted the initiation of the Anglo American Platinum Graduate Development Programme (AGDP) in 2002. Graduate metallurgists in South Africa enter the industry from different undergraduate programmes at various tertiary institutions, and so the knowledge and skills of the young graduates varies. Further, the geographical expansion of the industry combined with the downsizing of business units means that there are fewer opportunities for young graduates to be mentored through their first few years on site. Anglo American Platinum chose to address these issues by implementing an intensive, structured graduate training programme for all their new metallurgical graduates, known as the AGDP. The first two years of experience of the AGDP, from the viewpoints of both graduates and lecturers, were presented to the mineral processing community at the IMPC in Turkey in 2006 (Sweet et al, 2006). From the beginning, the programme was structured in a modular fashion to include a basic technical ?toolbox? including statistics, the scientific method and sampling protocols, while the mineral processing content comprised advanced learning in comminution, classification and flotation (later extended to include hydrometallurgy). Technical communication ? both written and verbal ? was included from the start. The programme was focussed very strongly on site work (?learning by doing?), with a major integrated site campaign conducted and analysed by each cohort. In 2012 the AGDP will accept its ninth cohort into the programme. This paper describes how Anglo American Platinum and the University of Cape Town have developed and adapted the programme over the last few years, in response to the challenges of the global recession, skills retention, and the changing operational needs of the company. The programme, which was drawn up to accommodate around 15 concentrator-only graduates, now accommodates 35-40 concentrator, smelter and refinery graduates annually. The programme has also been modified to facilitate new graduates spending most of their first year on the operations. The benefits of the programme for Anglo American Platinum have been tangible, and will be discussed in the paper. Keywords: graduate training, technology transfer

Sep 1, 2012

By S. C. Borah

Graphite, a mineral form of pure carbon, is one of the most versatile minerals in industry, because of its varying physical properties and characteristics. The mineral occurs naturally in the form of tubular crystals or microcrystalline earthy lumps, or it is disseminated in rocks, which have undergone intense metamorphism. India has a large deposition of graphite minerals out of which about 43% are found in Arunachal Pradesh. However, compared to the rest of the country, the North-East Region and particularly Arunachal Pradesh has not attracted attention till date for detail investigation for characterization, beneficiation, prospecting and/or exploitation of the mineral resources including graphite. Bulk graphite sample were collected from upper Subanshiri district of Arunachal Pradesh. Chemical analysis of the representative samples were carried out and found that 7.29%, 19.60% and 6.07% of fixed carbon (FC) is present in graphite sample collected from La-Lamdak, Bopi and Taliha, Arunachal Pradesh, respectively. Chemical analysis of the ash of the graphite sample shows presence of impurities such as silica, Al2O3, Fe2O3, Ca, Mg etc in the graphite sample which are also supported by XRD and SEM-EDX investigation. The graphite samples of Arunachal Pradesh are low grade and do not fulfill the market requirement for the industrial applications. Therefore, low-grade graphite is subjected to beneficiation for the upgradation of the graphite for industrial applications. We have adopted the dispersion?cum-settling technique for the beneficiation of the graphite sample collected from Arunachal Pradesh. The FC of 40.21% with 41.17% raw graphite recovery which is equivalent to 71.02% carbon recovery have been obtained by gravity separation technique using only distilled water without any chemical reagent in case of graphite sample collected from Bopi, Arunachal Pradesh. The graphite sample is upgraded up to 47.75% FC with 41.91% raw graphite recovery, which is equivalent to 85.85% carbon recovery with the pH adjustment at 9 with NaOH. Keywords: graphite, beneficiation, gravity separation, arunachal Pradesh

Sep 1, 2012

By Yuhe Tang, Jun Zhang, Jianguo Liu

"The nature high carbon graphite with fine particle size has low commercial value because of its narrow application range. In order to improve its value, this paper has studied the methods for nature spherical graphite. The nature spherical graphite can be used as the battery material in the field of electronic product battery and new energy automobile battery, basis on the physicochemical characteristics and particle feature of graphite. In this research, the Fixed Carbon (FC) grade of the graphite sample is more than 95.0% and the particle size of the graphite sample is from +325 mesh to -100 mesh. There are many methods for nature spherical graphite, including the fluidized bed airflow mill, the hydro-spheroidization mill and micropowder mill. The testing results indicate that the method of ACM micropowder mill is the best because the spherical shaping ratio and production yield of spherical graphite are both the best.According to the testing results of the ACM micropowder mill, the best process includes two stages of coarse crushing, four stages of fine crushing and twelve stages of shaping. And two kinds of spherical graphite products can be got, which are the product of D50=22.85 µm and the product of D50=15.43µm, and the whole yield of them is up to 54.43%. So, it lays a foundation for the high value utilization of this kind of graphite resources.INTRODUCTION Graphite is isomer of the diamond. Graphite ore resources are mainly concentrated in China, Brazil, India, followed by Czech, Korea, Mexico, Canada and other countries. Graphite ore has lots of characteristics by itself crystal structure, such as good resistance to high temperature, electrical conductivity, thermal conductivity, thermal shock resistance, good lubricity, plasticity, chemical stability and so on. So, Graphite is widely used in metallurgy, machinery, electrical, chemical, petroleum, nuclear industry, defense industry and other areas. [1,2,3] Natural graphite ore has low geological Fixed Carbon (FC) grade. FC grade should be enriched to more than 94.0% by mineral processing. [1,2] The particle size composition of this high carbon graphite affects its application value. The part of +100 mesh particle size has high application value. The part of -100 mesh particle size has low value because of its limited application field. In order to improve the value of-100 mesh particle size, this part high carbon graphite can be made into spherical graphite. And the value of the spherical graphite is great, it is more than 8 times of the feed. This paper has lots of tests for spherical graphite preparing with the fine particle size natural high carbon graphite. And it lays a foundation for the high value of this kind of resource."

Jan 1, 2018

By L. Simpson

South African is a repository of significant deposits of a variety of minerals. The Citigroup confirms this assertion with an estimate of in-situ valuation of US$2.5 Trillion. The mining sector plays an important role in the South African economy. In addition to the mineral resource base South Africa has other comparative advantages. Firstly, South Africa retains major mining companies that participate globally, including Anglo American, Goldfields and De Beers. Their global involvement offers much to the local mining sector and the broader economy. Secondly, government established research councils. The Council for Geoscience (CGS) was established to manage the Geological Survey of South Africa, including the reduction of geo-scientific investment risk. The Council for Scientific and Industrial Research (CSIR) promotes industrial development, including mining technology development. Mintek undertakes mineral research from mineral examination of ores, to extraction and refining technologies and manufacture of end products. Thirdly, South African universities teach and conduct research along the mineral value chain. They have increased their minerals graduates? capacity, thus advancing knowledge and skills. Knowledge and technical progress are behind productivity growth and emergence of competitive advantage. The research and development (R&D) capabilities of industry, science councils and universities, working in unison, will enhance the competitiveness of the South African mining industry. The National System of Innovation (NSI) requires multi-disciplinary, collaborative research. Key R&D elements, including skills and expertise, funding and facilities, must be available to implement a long-term national strategy or programme. Improved international collaboration and partnerships between government, academia and industry driven human resource development (HRD), ultimately develop the critical mass for inter-generational skills requirements. This trend requires an expansion of research collaboration programmes. Decisions involving investments and collaborative actions pertaining to R&D in the sector necessitate an analysis of the South African mineral value chain R&D capability. This paper analyses the evolution of R&D capability from exploration to refining, tertiary education, science councils and industry. The political economy of the evolution of this capability is analyzed in relation to the central role that the South African government plays in creating an appropriate supporting environment and related initiatives to enhance R&D and innovation. Keywords: research and development (R&D), science councils, universities, industry, innovation policy, South Africa

Sep 1, 2012

By Diana Drinkwater

As ore grades decline, ore deposits get harder and mineralogical complexity increases, metallurgical skills are more important than ever to ensure that today?s mining operations are operating efficiently and profitably. Yet specialist undergraduate degree programs have all but disappeared and metallurgical skills training for graduate engineers in the workspace if often haphazard. In response to this situation, specialists at the JK Centre in Queensland, Australia, have put together a professional development program designed to fast-track skills development for early career metallurgical professionals. The program, called ?MetSkill ® ?, is offered as a group training package for young metallurgists in the workplace. It is centred on a meaningful technical investigation negotiated between the JK Centre delivery team and the client company. As well as learning about project management and data collection and analysis, the participants study specialist topics such as comminution, flotation and mineralogy under the tutelage of senior research and consulting professionals. The technical investigation provides an opportunity for immediate practice of these new skills and JK Centre specialists are on hand to provide feedback and support throughout the program. The participants are employed across different operations in Australia and the Asia-Pacific, and although they occasionally come together for group training activities they are often separated by considerable distance. Specialist educational professionals from The University of Queensland have provided an innovative web platform to support collaboration and communication between all participants. This paper will describe the MetSkill ® program in detail, as well as providing a report on its initial roll-out to 2 groups of Australian graduate metallurgists in 2012

Sep 1, 2012

By Jannie van Deventer

"Innovation in the minerals industry has been lagging behind comparable industries like oil and gas. An incremental innovation culture that tolerates long lead times between invention and adoption has been exacerbated by a research grant structure that inhibits radical idea generation. Entrepreneurs who can make the link between ore source, technology and finance will cause a shift in innovation culture and open up substantial opportunities in the minerals industry of the future. By extrapolating existing trends in technology within and outside mineral processing, a crystal ball vision of future innovation is shaped with the aim to lower energy and water demand, reduce CO2 emissions, decrease operating and capital costs, reduce environmental impact, and secure a social licence to operate. Advances in nanotechnology, advanced materials and biotechnology will impact mineral processing, but the initiative for technology transfer must come from mineral processors. Laminates of graphene oxide can offer efficient filtration and separation media, while microfluidic devices will be used for desalination, solvent extraction and analysis. Substantial progress is expected on benign lixiviants and separation agents, such as nanoscale supramolecular hosts that can serve as high-capacity, selective and recyclable ligands and sorbents, and solid aminobiphosphonate-based adsorbents. Radical ideas for the recovery of precious metals from non-assayable ores and the generation of energy above unity will be adopted in selected minerals projects. In-situ mining in which microbes generate lixiviants at mineral surfaces will simplify processing circuits. Specific ores will be subjected to microwave processing and electropulse liberation to enhance recovery. Ultrafine grinding using devices of low energy consumption will be done mainly dry, followed by dry separation. New flotation cells will remove efficiently either coarse particles or ultra-fine particles, with mineral surfaces being modified not just by new reagents but also by selective microbes. Innovation in mineral processing indeed has a bright future."

Jan 1, 2014

By Dominic Howarth, Diana Drinkwater, Don McKee

At a time when the mining and minerals industry across the world is undergoing unprecedented change, the very fabric of the tertiary education system which is the principal source of trained professionals to the industry is in decline in many countries. The change sweeping the industry is globalisation as evidenced by the emergence of a relatively small number of increasingly dominant corporations with operations in most of the major mining countries. The education sector is struggling to provide sufficient graduates as the viability of small mining schools declines. That is only part of the problem as the global operating industry is increasingly seeking graduates who are comfortable working in different countries and cultures. One obvious response to the industry needs and developments is for the education sector to consider how it can best respond to the global opportunities. This paper presents the case for a global education network which is based on a network of international thinking Universities and which makes use of the latest in educational thinking and technologies to provide a quality education and in the process produce graduates fitted for international careers.

Jan 1, 2003

By Francesco Montanari, Gianni Schena

"Recent improvements in X-ray computed tomography allow investigation of objects several tens of millimetres in dimension with spatial resolutions in the order of a few microns. These improvements are made possible by coupling the micro-focus technology adopted by some of the latest cone-beam X-ray sources with an increase in the efficiency of the detectors. The micro-focus technology allows the production of clearer images at high magnification by reducing the penumbra (fuzziness) associated with larger focal spot size.Even higher resolutions can be expected in the next few years with the commercialisation of nano-focus X-ray tubes. In practice one can inspect a system of fine composite particles and analyze the different mineralogical phases in each individual particle. Computed tomography allows accurate liberation studies, e.g. providing liberation spectra or washability data in tens of minutes. However, on-line application of micro-focus computed tomography is unlikely in the foreseeable future, despite rapid development.Dual-energy (DE) radiography is another X-ray technique, which allows retrieval of the volumetric content of valuable components in two-phase particles in a fraction of a second. A digital radiograph of a single two-phase particle produces a grey level image, where the luminosity of the pixels is determined by the sum of the attenuation levels of all the structures. Thus morphological and compositional effects concur to produce the radiographic image, which does not allow retrieval of the composition of the particle, as the 3D-structure of the particle is compressed into a 2D-image, with an obvious loss of information. Thus, in principle it is not possible to discriminate between thick, comparatively penetrable, and thin, comparatively impenetrable mineralogical components."

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

"The pressures on mining and minerals education at the tertiary level are well known. Within Australia, for example, the number of undergraduate mining engineering courses with 30 or more students in each year has reduced to three (University of Queensland, University of New South Wales and Curtin University). Similar declines in both student numbers and participating institutions are evident in many other parts of the world, and notably in USA and most countries in Europe.An in depth study of the Australian sector was conducted in 1997/1998, resulting in the Back from the Brink report (Carter 1998). The Australian situation was summarised as follows.Australia’s minerals education system, in its current form, is fragile and is in no position to seize the opportunity (i.e. world leadership in minerals education) and is more likely to succumb to the threat.Current trends include:- an acute shortage of talented academic staff, as a result of University remuneration packages having become hopelessly uncompetitive with those in the minerals industry;- small student populations and high relative costs, making mineral specific courses vulnerable to closures, when Universities are under extreme cost pressures; this situation will be exacerbated if enrolments drop in response to, say, a cyclical down turn in the industry; and- under-resourcing of minerals departments because of their comparatively small size, making these departments incapable of delivering top class teaching in all aspects of their courses, despite being excellent in some areas.Most of the Australian issues identified above have direct parallels in other countries.The most common response of institutions to the threats is to seek strength, and in some cases survival, through various forms of linkages and networks. A number of these associations, which are frequently defensive in nature, are outlined in the paper."

Jan 1, 2003

By V. Grujic, M. Grujic, D. Salatic

"Two areas are involved in the research work of the comminution process (crushing and grinding). The first one involves the changes of the size class distribution values that are definded by the differential equations in the function of the ore property and working conditions. The second area involves the comminution of the different levels in order to optimize the working parameters and to decrease the operational costs in the grinding process.We have studied, in detail, the possibility of functioning the crusher at the maximal loading, over 4500 kN, ball mills with diameters larger than 5.0 m and semiautogenous mills with diameters larger than 10.0 m.Using the computers, we have achieved the maximal loading range of the crusher, over Fc ? 4500 kN in the crushing process. In the grinding process, using the adequate differential equations in the automation process, we have established the correlation between the pulp mass capacity in the mill, pulp dencity, ore fineness in the pulp and recirculating ore charge.With the appopriate text, equations and graphs, this paper shows the results of our several years research work in the laboratory and in the ore comminution plant of Majdanpek Copper Mine."

Jan 1, 2003

By Shailin Lalloo, Allan B. Nesbitt

"Gravity separation by centrifugal equipment, particularly in the mineral processing industry is a novel approach of optimising product recovery. The manufacture and sale of centrifugal equipment by recently established companies is now beginning to have a significant impact on the industry. Some benefits of operating at increased gravity include: reduced environmental issues, a shorter lead time, lower capital cost and improved recoveries of elemental mineral before entering the grinding circuit.Of topical discussion is the use of centrifugal separators for the recovery of less valuable minerals that will form a greater proportion of the feed compared to traditional scalping circuits where the gold content is extremely low. This ultimately results in the centrifugal system having to have a greater mass pull. In addition, the relative density difference between gangue and valuable mineral is likely to be less and therefore modelling and optimisation of this separation process will be necessary. Some researchers have muted using fluidisation models to model the forces present in the separation zone of a centrifugal separator2. It is not unusual for the manufactures of centrifugal separation equipment to use fluidisation terminology to describe what happens in the separation zone. Most fluidisation models are based on the empirical/classic relationship between superficial fluid velocity and voidage postulated by Richardson and Zaki. However, no researcher has proved the effectiveness of this relationship in an increased gravity Environment."

Jan 1, 2003

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014