Search Documents

By A. David Miller, Douglas M. Barber

"The Rocky Mountain Arsenal was used by the military to produce chemical warfare agents and incendiary munitions for use during World War II and later by private companies for the production of industrial and agricultural chemicals. After an investigation performed in accordance with CERCLA confirmed significant levels of contamination due to the common industrial and waste disposal practices of the era and the discovery of over 300 species of wildlife inhabiting the land the Rocky Mountain Arsenal became a wildlife refuge and contamination cleanup efforts began. Three lime basins originally used to treat wastewater from the chemical production were decided to be contained in place, requiring a seepage barrier installed around the perimeter of the site to further prevent groundwater/contaminant migration. This case study will discuss the successful installation of a soil-bentonite cutoff wall around the area using deep soil mixing. Highlights of this case study will also include a discussion of the challenges faced due to construction activities performed with Level B Hazmat PPE requirements as well as added challenges brought on by the Winter season, after the project was delayed due to a positive air monitor detection for the chemical weapon Lewisite during construction of the work pad.INTRODUCTIONThe Rocky Mountain Arsenal (RMA), located just outside of Denver, Colorado, was established by the United States Army in 1942 to produce chemical warfare agents and incendiary munitions for use during World War II. Following the war, and as weapons production decreased, portions of the site were leased to private companies for the production of industrial and agricultural chemicals. The principal lessee, Shell Oil Company, manufactured mostly pesticides at RMA facilities from the early 1950s to the early 1980s.In 1984 an investigation began in accordance with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and confirmed significant levels of contamination due, in large part, to the common industrial and waste disposal practices of the era. It was also discovered that over 300 species of wildlife inhabited the land in the absence of regular human activity, including a group of bald eagles, leading to the passing of the Rocky Mountain Arsenal National Wildlife Refuge Act in 1992."

Jan 1, 2015

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Jim Glider, Noah Miner

The Gordie Howe International Bridge is a project to build a cable-stayed bridge and border crossing across the Detroit River. With a span length of 2,800-ft (853.4 meters), the Gordie Howe International Bridge will have the longest main span of any cable-stayed bridge in North America. Each tower has two legs that are supported by six drilled shafts each for a total of 12. The tower shafts are 9.84 feet in diameter (3-m) and extend well into bedrock. 17 each, 6.6 feet (2-m) drilled shafts were built to support the aging river bulkhead and replace shipping bollards. In addition to shallow groundwater fed by the Detroit River, artesian conditions at depth result in a water head that is approximately 17.2-ft (5.2-m) above surface. At 95-ft (29-m) below grade Dundee Limestone, of the Detroit River Group, is moderately weathered and fracture density decreases with depth. The Dundee Limestone strength ranges from 8-ksi (55.1-MPa) to 12-ksi (82-MPa) and may carry hydrogen sulfide in fractures. Working through casing that sticks three stories out of the ground is less than ideal, but was necessary to maintain a positive fluid head and prevent artesian-related quality issues. The sheer scale of the bridge forces required a load test configuration that could impart an equivalent static load of over 38,000,000 pounds (170-MN). A suite of QA/QC tests was developed to ensure the shafts would meet the project plans and specifications to include critical base cleanliness criteria. Interesting CSL and TIP results obtained highlight the strengths and weaknesses of each test method. Cleaning drilling fluids with a centrifuge allowed recycling of product and reduced exposure to environmental contaminate exposure. Having large construction equipment working next to the river presented challenges in working pad design. A driven pile system was developed to support high oscillator forces and protect the aging seawall.

Sep 8, 2021

By Joram M. Amir

During recent years, the integrity testing of piles has made considerable progress. With the availability of portable and powerful computers, practically all integrity testing equipment is now digital. Using sophisticated software for data acquisition and analysis, today's testing systems can provide owners with important information regarding both the length and integrity of piles and drilled shafts. This sophistication carries a price: Very few clients, including experienced engineers, do understand the strange-looking graphs adorning the reports they get. In fact, most of them will never ask, some because they are too busy to care and others because they are ashamed to show their ignorance. This situation is well exploited by a few shrewd operators of test equipment. Facing strong competition and falling revenues, they simplify their task and cut their expenses by the following means: 1. Using old equipment until it falls apart, and then some, 2. Hiring under-qualified personnel, 3. Staying on site as little as possible, 4. Eliminating the analysis and evaluation stage altogether, 5. Confirming as-made lengths and reporting no defects.

Jan 1, 1999

By Tony D. Canale, Anthony Mazzo

"Times Square, arguably one of the best-known destinations in the world, has undergone and continues to undergo a re-development aimed at attracting corporate tenants to the area. Mueser Rutledge Consulting Engineers (MRCE) was involved with the planning, design and construction of the foundations for the Conde Nast and 5 Times Square sites, as well as Times Square Tower. These sites are pictured in Figure 1.This paper will focus on the design and construction of the deep foundations for Times Square Tower that was developed by Boston Properties. PROJECT DESCRIPTIONTimes Square Tower is 47 stories tall, with no setbacks and an overall height to top of crown of 730 feet (222.5m). It has two basement levels extending 30 feet (9m) below grade over the full site. As shown in Figure 1, the structure occupies the entire site and has a footprint of 22,000 square feet (2,044 m2), with a total rentable area of about 1.2 million square feet (111,480 m2). The planned use for the building is office space with retail at the ground level. When completed, Times Square Tower was the final building constructed as part of the Revitalization of Times Square. Due to the site constraints, designing and constructing the foundations was akin to placing the final piece of a puzzle.Times Square Tower provided numerous design and construction challenges that were a result of tight working conditions, heavy column loads, and a compressed schedule.GEOLOGIC SETTING AND SITE HISTORYThe Times Square area is part of the Manhattan Prong called the Manhattan Ridge, a formation of old and durable metamorphosed and folded bedrock, now termed the Hartland Formation. The bedrock generally has a thin soil cover and uneven surface overlain in some areas with a thin mantle of decomposed and/or weathered rock. Overburden soils include glacial and post-glacial deposits and recent fills.Transit improvements have been made in and around the Times Square area since the early 1900’s. The 1, 2 and 3 Subway Lines that run below 7th Avenue were constructed circa 1915 using cut and cover techniques and extend about 28 feet (8.5m) below grade. The N, R, Q & W Subway Lines that run below Broadway were also constructed in 1915 using cut and cover techniques and extend about 38 feet (11.6m) below grade. The 7 Line that runs below 41st Street was constructed later, using both cut-and-cover and tunneling methods as it runs below the other subway structures at a depth of about 55 feet (16.8m) below grade."

Jan 1, 2005

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005