Search Documents

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By Han Xuanjiang

Through whole analysis of static testing piles information of a teaching building, this paper put for ward that when the ratioes of unload rebound amount to residual deformation and to total settlement reach the maximum, the testing load is selected as allowable capacity of single pile by camparing with the settlement in the practical engineering, it is proved that this method fits to practice, for other several projects, its also available. Therefore non-destructive testing pile method was improved, so all the tested piles can be reused as engineering piles.

Jan 1, 1991

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Magued G. Iskander

The deterioration of concrete, steel, and timber is a serious hindrance to construction in marine and corrosive environments. Composite materials such as fiber-reinforced polymers (FRP) can offer performance advantages for construction in these environments. In the last decade, piling made of FRP composites has been used experimentally throughout North America. However, composites face obstacles because they do not have a long track-record of use in civil engineering structures. A comprehensive review of the current experience in research, testing, design, and practice of composite piling is presented in this paper.

Jan 1, 2002

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By George Goble

I hope that after the long evening and all the exercise that some of you took you won't be completely exhausted to listen to a little bit about pile testing. The topic that 1 have been given is pile testing. It seems to me useful to break this topic into some smaller pieces so that we can try and organize our thought a bit. As I understand the terms "pile testing", I believe we are really referring always to capacity, one way or another, so I am suggesting that we organize the things we are doing in terms of measurement of soil capacity and pile capacity. There are obviously two failure modes and we frequently speak of pile integrity rather than structural pile capacity, but it's really capacity that we are concerned about. Further within these breakdowns I am suggesting that we might look at the topic of soil capacity in terms of static methods and dynamic methods and, finally, within each one of these, measurements of axial capacity and measurement of lateral capacity. Also here some of these subdivisions might be there for the purpose of symmetry and finally the same sorts of breakdown in Pile Capacity area.

Jan 1, 1994

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014

By Rick Deschamps

The Block 76 project includes the demolition and redevelopment of an entire city block for mixed use retail, office and residential properties directly adjacent to Historic Temple Square in Salt Lake City, Utah. Excavation was carried out 65 ft below street grade and by as much as 50 ft directly below adjacent buildings supported by shallow foundations. Movements of the earth retention system and adjacent buildings were monitored in real time using automated equipment which complemented traditional geotechnical instrumentation. In the areas immediately adjacent to the existing buildings 9 stories or greater, anchored diaphragm walls were employed. Areas of the site not supported by diaphragm walls employed a soil nail wall system. Jet grouting was used for water cutoff in lieu of dewatering along the north and east sides of project. In total, the earth retention scope included 45,000 sq. ft of diaphragm wall, 104,000 sq. ft of soil nail wall, and micropile underpinning of 3 buildings. This paper provides an overall description of the Block 76 project. A detailed account is provided of the technical and commercial lessons learned. The project provided a unique example of how an owner can receive best overall value by acceptance of some technical risk up front. Benefit was gained by allowing the contractor to reduce contingencies within the bid from unknowns on a fast-track project.

Jan 1, 2009