Search Documents

By Andreu J. Ferrero

Polyurethane and acrylate resins are routinely injected into soils to gain strength and control water flow. However, most published data regarding strength gain is derived from laboratory samples created under ideal conditions. This study endeavored to inject resins into full scale mock-ups that could then be excavated and tested to yield results comparable to actual field conditions. To achieve this goal, a large container was filled with a silty SAND (SM), as defined by the Unified Soil Classification System (USCS). The soil was moisture treated and compacted in lifts of 0.3m. PVC pipes installed in a diamond grid into the soil were used to inject polyurethane and acrylate resins. Dynamic cone penetrometer (DCP) tests were conducted on the polyurethane treated soils, the acrylate treated soils, and the baseline untreated soils in the container. Testing results will be correlated to SPTn and CBR values to evaluate increases in the soil strength parameters in the treated soils. Cored samples of polyurethane and acrylate treated soils will be tested in compression, shear, and triaxial. These laboratory test results will focus on material property gains for the treated soils, in comparison to standard values for similar soil types. Complete documentation of the soil type, compaction methods, injection methods, and testing performed have been documented and will be presented in the final paper.

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"In order to achieve tubular pile driving with low noise and low vibration, the Press-in Piling Method has been adopted on many projects. The method utilizes reaction force derived primarily from previously driven piles to push in the next pile into ground. With attachments, the Press-in piling equipment can deal with hard soil as well as difficult site conditions. At West Toronto Diamond Rail Grade Separation Project in Toronto, Canada, the Press-in piling equipment drove more than 500 of 914 mm (36 inches) diameter tube piles in length of 12 to 25 meters (39 to 82 feet) to construct earth-retaining walls for railway grade separation. Myoshoji River Restoration Project in Tokyo, Japan drove some 600 of 1,000mm (39.4 inches) diameter tube pipe sections in length of 11 to 22 meters (36 to 72 feet) by the rotary Press-in piling equipment to increase the flood drainage capacity of an existing river in highly populated area of the city. Both projects exemplify the advantages of the method in urban settings.1. BACKGROUNDThe Press-in Piling Method was invented some forty years ago in Japan, where a very large number of construction projects were causing widespread construction pollution, especially by pile driving work in densely populated areas. The method has been providing solutions for piling projects which could not have been built otherwise due to the noise and vibration impact to the surrounding communities. The method can be used with various types of piles including sheet piles, tubular piles, concrete sheet piles and so on. With high pressure water jet and continuous flight auger attachments, the Press-in piling equipment can deal with dense sand, stiff clay, gravels, boulders and even soft rock without employing a different set of equipment."

Jan 1, 2015

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By Andrew Higgins, Jamey Rosen

This presentation will demonstrate some recent advancements in the applications of Project Information Systems (PIMS) technology to seepage barrier walls in the context of evolving Owner Specifications. The use of geospatial technology in particular is used to track, visualize, and analyze data from a variety of sources and serve those data to contractors and owners via dashboards and as-built drawings. Data describing the geometry of construction elements (including diaphragm panels, secant piles, and jet grout columns) is of particular importance on these projects, and this presentation will include case studies in the United States of how these data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage).

May 1, 2022

By Andrew Middleton, Mark Wyatt

"The Brickworks Marketplace Project is a significant shopping centre development in inner north west Adelaide constructed by Badge Constructions in 2014 and 2015. The site was a former brickworks with a deep pit containing various extents of uncontrolled fill which was to remain on site, and with a remaining void up to 6 m in depth. The existing uncontrolled fill was improved using the High Energy Impact Compaction system, and the pit backfilled using a quarry crusher byproduct selected by trial and a recycled crushed concrete and bricks and compacted in deep lifts. This approach resulted in significant savings in compaction time, cost and building foundations. The settlements of various parts of the completed works have been monitored since February 2015 and this monitoring has demonstrated small settlements which meet the user’s constraints.INTRODUCTIONThe Torrensville Brickwork Markets project involved the transformation of a former brickworks and clay pit site into a regional 17,000m2 shopping centre, opening in June 2015.The site was a former brickworks with adjoining clay borrow pit. The clay pit had been partially backfilled over many years with ‘uncontrolled’ fill comprising ‘clean’ soil, bricks and kiln dust typically of the following thicknesses:??of the order of up to 7 m to 10 m but locally up to 15 m in the western part of the site??2 m to 5 m in the south-eastern part of the site; and??less than 0.5 m in the north-eastern part of the siteAnecdotal reports suggested compaction of some of the fill may have been undertaken, although this not able to be confirmed nor records obtained.Initially it was proposed to take up the existing uncontrolled fill, sort and recompact or remove to landfill, followed by backfilling in conventional means over 500,000 cubic metres of imported filling to a thickness of up to approximately 6m to backfill the former pit. This work represented a significant cost and was not economically viable.During early negotiations, the contractor proposed an alternative to retain and ground improve the existing filling on site, and to backfill the pit with fill placed and compacted in deep lifts, thereby significantly improving the economics, environmental and community impacts of the proposed works.The developer agreed to the proposal with the following performance criteria:??a settlement of =10 mm after 10 passes by the Impact Compactor (on existing subgrade areas);??a bearing capacity of 250 kPa for high level footings;??a maximum long term differential settlement of 40 mm (measured over 16 m), ie. 1 in 400; and??a minimum modulus of 40MPa."

Jan 1, 1900

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By Venkatesh S. V J, Shubha M, Srilakshmi G

Choosing for the best option of pile foundations to overcome large lateral and uplift loads for the foundations in transmission line towers/offshore environment is still being a concern to achieve the required capacities but also by considering the suitability aspect in the environment. The objective of this paper is to review the methods that have been done for knowing the uplift resistance and lateral resistance of pedestal piles. Investigations by different methods such as experimental studies, numerical and analytical studies have been done by various researchers in order to evaluate the response of a belled pile. These methods are discussed in this paper and the comparison with straight shaft pile based upon the test and analysis. The results indicated that the uplift resistance and lateral resistance were significantly increased with the adoption of belled piles than straight shaft piles.

Sep 1, 2022

By Thai Nguyen Ph. D

Dynamic Load Test (DLT) on driven piles has been performed routinely all over the world. In several recent projects, even 100% testing has become a norm where every single pile is dynamically load tested. In these cases, most piles are of uniform sections, making the field analysis (CASE method) straight forward. The CASE method, which has been used for the last 50 years, however, is only applicable to uniform piles to monitor pile driving stresses as well as pile capacities. Signal matching analysis can handle different configurations. However, the analysis used to require user inputs (i.e., non-automatic). Manual signal matching analysis, which can solve non-uniform solutions, traditionally takes hour(s) to complete for one blow. As such, the real-time pile driving stresses and resistances had traditionally been relying upon the CASE method, using typical range of CASE damping (JC). Until 2021, due to the lack of a rigorous instant signal matching analysis for non-uniform piles, no tool was available to help engineers evaluate non-uniform piles in real-time. An inexperienced field engineer may overlook this shortcoming when evaluating peak driving stresses. Furthermore, ultimate bearing resistances for non-uniform piles may require further evaluation to account for the non-uniformity of piles if relying on the CASE method. This paper highlights recent advances in instant Signal Matching Analysis on non-uniform piles, allowing field engineers to monitor stresses and resistances of non-uniform piles during driving.

Oct 1, 2022

By Zhang Wengang, L. John Endicott

The properties of many geological materials are variable. This is especially true for variations in elevation of the top of rock profile, strength of weathered rock, and conductivity of rock masses. Often the site investigation stage is completed by site specific ground investigation utilizing boring, sampling, and testing. Statistically this is a sampling procedure, but the borings are often widely spaced, and ground conditions between borings are deduced by interpolation. Often budgets are a limiting restraint and the information that is obtained may be less than desired. Sampling and testing is often biased. If claims for unforeseen ground conditions are to be avoided, the properties of the ground should be adequately identified. This paper describes how data can be used to evaluate the subsurface top of rock profiles, and can give insight into representative, maximum, and minimum strengths, and variation in conductivity relating to inflow of water into excavations, that can assist in planning the works and also in resolution, or avoidance, of disputes about unforeseen ground conditions. INTRODUCTION The mechanical properties of the ground are naturally variable. The work of Geologists, Engineering Geologists and Geotechnical Engineers is fundamentally investigative. Frequently, budgets for ground investigation are squeezed, resulting in widely spaced boreholes, with conditions between them determined by interpolation. Profiling can be adopted but the measurement, such as seismic velocity, is used as an indirect means of computing in-situ profiles and mass properties. Often a lot of test data are generated on large projects or by many projects in the same vicinity. Published data enlarge the database for a given project, and databases can be interrogated to gain insight into different categories of ground. Integration with geological studies can then lead to more reliable characterization of the ground in terms of identifying the materials present, their extent and their range of properties. This paper focuses on properties of rocks that are generally required for ground engineering, namely the top of rock profile, the unconfined strength of rock materials, and the mass conductivity. Data are obtained from Granodiorite and Granite in Hong Kong, and from Granite and the Jurong Series of weakly metamorphosed sedimentary rocks in Singapore. All four rock types have been tropically weathered, resulting in widely varying top of rock profiles, material strengths and mass conductivity. With a wide range in values for these parameters, project specific ground investigation conducted within a limited budget may run the risk of falling short of obtaining sufficiently reliable data sets, resulting in risk that unforeseen ground conditions may be encountered.

Jan 1, 2019

By Gary L. Seider, Dana A. Wesolek, Fred C. Schmednecht

"A new condominium project, The Atelier, developed by Pickus Companies located at the corner of Bryn Mawr and Sheridan in Chicago, IL required an earth retention system to protect the surrounding roads, alley, and existing neighboring apartment bui lding during its construction. Slurry Systems, Inc. (SSI) and Ground Engineering Consultants, Inc. designed the earth retention system using cantilevered sheet piling for three of the four sides: two sides bordering major streets and one side bordering an alley. For the fourth side, which borders an existing occupied brick building, a combination of sheet pil ing and AB. CHANCE® helical screw piers were used. SSI was actively involved in the review process of its earth retention system with the City of Chicago and quickly learned that there was no specific code for hel ical piers/anchors. (It appears that this is the case with most metropolitan cities throughout the United States). Consequently, the approval of underpinning for this project became the critical path, as much testing, calculations, meetings, and other details were required prior to its approval.SSI and AB. CHANCE® recognized that this process for underpinning approval must be seen by other contractors/suppliers who wish to use helical piers/anchors in the City of Chicago. Consequently, this project served as an opportunity to work with the City of Chicago and the City's Building Code Committee in furthering the development of the Helical Piers/Anchors Code, Section 1814. INTRODUCTION - HELICAL PIERSDefinition. A helical pier or anchor consists of one or more helix-shaped steel bearing plate(s) attached to a central steel stem (solid bar or pipe), which is installed by rotating or ""torquing"" into the ground. Each helix is attached near the tip, is circular in plan , and is formed into a screw thread with a defined pitch. Helical piers/anchors are pre-fabricated and can derive their load-carrying capacity through both end bearing and skin friction. The helical piers/anchors can be augmented with grout."

Jan 1, 2005

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Gilbert R. Tallard

"Pouring deep foundations by the tremie pipe method is nowadays such a common process that it has becomes an unspecified practice. Means and methods are almost entirely at the contactor’s discretion. A variety of practices are permitted and seldom associated with the discovery of abnormalities and areas of random defects in concrete. This writer wishes to call the attention of stakeholders to the initiation details of the tremie pour operation.KEYWORDSINTRODUCTIONThe advent of slurry as a means of shoring an excavation of relatively small cross section but of possibly great depth has become part of state of the art in foundations construction, with the substitution of said slurry by concrete to provide the structural end product element through the use of tremie pipes. In appearance, there is nothing more simple than pouring concrete into a tremie pipe through a hopper after the basic work has been done i.e. the excavation or drilling, the cleaning of the slurry, the placement of the reinforcing cage, then the tremie concrete pour is almost a reward for a successful achievement. Force of habit has removed the awareness on the process fundamentals for initiating the pour; a variety of practices used call for a review and a reassessment as a means of reducing construction defects that may result from flawed practices, and and especially we are pouring deeper holes. This writer intends to address this issue focusing both on the drilled shaft and the diaphragm wall industries.TREMIE PIPES AND HOPPERSA tremie pipe diameter needs to be sufficiently large to allow the rapid descent of concrete with a minimum of friction loss and avoiding possible bridging in relation to aggregate size. Impervious joints between pipe sections are essential to prevent slurry “raining” over the concrete which can cause concrete segregation pockets and possibly plug the pipe with damaging consequences. That tremie pipes be long enough to reach the bottom may be self-evident but poorly written specifications can be erratic on that subject and seldom specific in terms of inches. A standard pipe of 10 inches is well accepted throughout the foundations industry; double O rings and spline joints are common and function well if properly maintained. However the practice to cover the joint with the ineffable duct tape indicates that all is not always well with this detail. Also, spline cables may shear in case of very long tremie pipes causing the separation of the tremie pipe requiring a restart in midstream with another probable source of inter mixing of concrete and slurry with subsequent defects."

Jan 1, 2017

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Frank Rausche

The more widespread use of Augered Cast-in-Place (ACIP) Piles has generated increased demand for improved quality control measures. These deep foundation elements are often relatively long and slender and their structural quality depends on the experience of the installers, the adequacy of their drilling and pumping equipment, and of course, the properties of the soil. Since the concrete of ACIP piles is pumped under pressure into the borehole, the piles may achieve a very high unit shaft resistance if conditions are favorable and the piles are well constructed. Three types of methods can help assure that the piles are properly executed. During construction, monitoring the volume of concrete pumped and the pressure applied helps avoid structural defects. After installation, and once the concrete has hardened, the Pulse Echo Method allows for a check of the structural integrity of the shaft. Finally, a load test, performed some time after installation, yields a check of both bearing capacity and structural integrity of an individual pile. Because of their expense and associated construction delays, static load tests are normally done for only a few piles. However, at large construction sites, it may be necessary to perform many load tests either as a planned construction control activity or as a means of spot checking or verifying suspect piles. For smaller sites, however, static load testing may be prohibitively expensive. In such situations, dynamic load testing, originally developed for driven piles, has frequently been employed for drilled shafts and ACIP piles. In the latter case special consideration must be given to the ACIP pile slenderness and their often relatively low concrete design strength, which may not tolerate high dynamic loading stresses even though their unit resistance along the shaft is relatively high. Lately, the dynamic load test has become more feasible with the availability of loading systems that are custom tailored to this particular pile type. These systems produce a low velocity, low stress and high energy impact. Recent developments have also made the instrumentation process simpler: force measurements are now made on the ram rather than on the pile for increased reliability and simplicity. This presentation describes the requirements for successful dynamic load testing of auger cast piles and summarizes results from several projects where the new loading system and newly developed instrumentation was employed. A few cases are presented correlating static load test results with dynamic predictions, calculated by CAPWAP®.

Jan 1, 2001

By Jamey Rosen, Georgette Hlepas

Verticality data collected from panel and pile elements of seepage barrier walls describe the shape and position of those elements in three dimensions. These data are used to determine if a barrier wall is constructed as designed and if it meets the owner specifications with respect to tolerance (i.e., if each element is sufficiently close to vertical) and overlap (i.e., do adjacent elements overlap sufficiently to prevent leakage). Contractors use verticality data to confirm that their work matches the design, and owners use verticality data to verify the contractor’s work and confirm that specified criteria were met. Project Information Management Systems (PIMS) technology has been applied to the management, visualization, and analysis of verticality data. This paper will provide examples of how contractors and owners have used a PIMS to compile and synthesize data collected during excavations (e.g., from Cutter Soil Mixer and Hydromill drill rig telemetry), and from measurements of completed excavations (e.g., using the Koden ultrasonic tool), and used those data to model excavation geometry. We will present case studies of using these models to estimate backfill placement volumes, and to evaluate the verticality tolerance and overlap between elements.

Sep 8, 2021

By Faisal Shalzad, Adnan Anwar Malik, Tadashi Maejima, Jiro Kuwano

Single helix screw piles carry most of the structural load through end-bearing if the helix is embedded in the dense bearing layer. The tip condition of the central shaft of the screw pile can be closed, closed with cutting blades, opened with flat cut, and opened with wedge shape cut and its selection is based on the insitu ground conditions. These different end conditions of the central shaft disturb the ground differently, leading to the change in bearing capacity. In this study, an attempt is made to investigate the effect of open and close-end screw piles on installation effort (installation load and torque) and bearing performance in the dense bearing layer. The model steel screw pile with a pile shaft diameter of 21.7 mm and helix diameter of 43 mm is used in this study. Test results show that the open-end screw pile required less installation effort than the close-end pile that penetrated the bearing layer by 1Dhwith an unplugged condition. Further, the open-end screw pile shows a higher bearing response than the close-end screw pile if it enters the bearing layer with an unplugged condition.

Oct 1, 2022

By Sailesh S. Author

The current design method for soil-cement (SC) columns improved soft clayey ground under the highway embankments assumes a slip circle failure surface shearing through the columns and the soils using a weighted average shear strength. However, the results from the laboratory centrifuge model test and numerical analysis indicate that in many cases, the SC columns fail by bending. Some researchers have proposed methods for estimating the maximum embankment loading for bending failure of SC columns, but those methods have limitations in correctly considering the internal shear stresses or not applicable for the group SC column improvement. Numerous model embankments on SC columns have been simulated by three-dimensional (3D) finite element analysis (FEA) and the mechanism of bending failure and the magnitude of the bending moment in the SC columns under embankment load has been investigated. Based on the simulated results, the design method for the estimation of the bending failure of floating SC columns has been proposed. The predicted results from the proposed method agreed with the existing field condition of one embankment in Saga, Japan reported in the literature in terms of the stability of columns. Hence the proposed method can be used for the design of floating SC columns in the soft ground.

By W. L. Chong

For a project located in Docklands Victoria, a high-rise development was proposed where the geology comprised soils of various compositions and consistencies to approximately 50m deep before being underlain by a siltstone bedrock. Due to the structural loads and spatial constraints, the majority of the foundation piles were designed to be socketed into the siltstone. Key factors in selecting the Continuous Flight Auger (CFA) technique as an effective piling solution are explained. These factors included structural and geological considerations, piling rig capabilities, pile testing regime to verify load performance and integrity, the extensive suite of construction quality controls and instrumentation records required while also achieving an appropriate piling budget and program. This paper also described how these factors underpinned the design approach of the final piling scheme. Critical aspects considered during construction and post-construction quality and pile testing records required to meet and satisfy the strict project piling specifications are also presented. The project adopted what may be considered the “best practice” in deep CFA piling. To the author’s knowledge, this project achieved the record for the deepest CFA piles in Australia where multiple piles to 53.8m deep were constructed.

Nov 1, 2022

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By Spencer Ness, Yazen Khasawneh, William Tjaden, Mohammad Nassim

The evaluation of long-term performance of the wind turbine structures is essential in lowering the Levelized Cost of Electricity (LCOE) from wind sources. The required maintenance of the wind turbine foundation during the design-life time of the wind turbine may result in escalated cost, if not properly evaluated during the planning and designing phases. The degradation of the foundation soils’ stiffness due to the accumulation small plastic strains resulting from normal and/or extreme operating cyclic loading may result in escalating the O&M cost. The foundation’s stiffness degradation will result in a shift of the wind turbine system natural frequency, which may result in amplifying the vibrations generated at the hub. The anticipated shift of the wind turbine system natural frequency during the design-life time should be investigated through numerical simulations of the anticipated dynamic loading utilizing soil constitutive models that are capable of capturing the foundation stiffness degradation due to the accumulation of such small plastic strains. This study presents the validation of an element model that will be used to evaluate the performance of existing and/or proposed constitutive model.

Oct 1, 2022