Search Documents

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Ganesh Deepak K., Anjana R. K., Dr. Kumar Pitchumani N., Rajasekharam R. M. V. M. S. S.

The Phase 2 of Chennai Metro is being introduced in the city to ease the dependence on the existing transportation systems. Phase 2 is a combination of underground and elevated metro stretches comprising of three corridors. The current study focusses on the underground stretch of Corridor 3 which has a total of 29 underground stations. Construction of the underground cut and cover stations results in ground movements, which in turn impact the structures adjacent to the excavations. The greenfield ground settlement can be evaluated with the help of empirical approach or an approach requiring finite element modelling (FEM). The paper compares empirical and FEM approaches with regards to ground conditions in Chennai. Further, with the predicted ground settlements, building damage assessment is performed. The damage category of a building is defined based on the estimated tensile strains. This paper also compares the building damage assessment with empirical method and finite element modelling.

Nov 1, 2022

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Keith MacKay, John Carter, David Siddle, Fernando Faminia

"The River Green Residential development, is located in the municipality of Richmond, BC adjacent to the Fraser River. Ground conditions at the site consisted of medium to fine grained alluvial sands and a high groundwater elevation. A temporary low permeability retaining wall was required in order to facilitate the construction of an underground parking structure without inducing settlement of adjacent structures, which include the Richmond Olympic Oval; part of the legacy of the Vancouver 2010 Winter Olympics. Golder Associates Ltd. and GeoPacific Consultants Ltd. utilized Cutter Soil Mixing (CSM) technology to enable construction of a continuous combined low permeability cut-off and retaining wall around the perimeter of the property. The 350m long wall was keyed into marine clay at a depth of 28m below ground surface, and contained H-Pile reinforcement installed at regular intervals. The CSM technology provided many benefits for this project, allowing the combined cut-off and retaining wall to be constructed within a very narrow footprint (650mm width). The low noise impact and near vibration free construction of the CSM equipment provided minimal inconvenience to nearby stakeholders during construction. To reduce dewatering volumes during excavation and prevent significant water-table drawdown the Hydraulic Conductivity requirements for the wall were 1 x 10-7 cm/s or less. Project specifications called for a different strength requirement for upper and lower portions of the wall. The top 13 meters of the wall required an Unconfined Compressive Strength (UCS) of 4MPa to act as a retaining and cut-off wall, whereas the bottom 15 meters of the wall required a UCS of only 0.5 MPa to act only as a cut-off wall. Wet-grab and core samples were obtained from the panels to confirm the UCS and Hydraulic Conductivity specifications were met.INTRODUCTIONGolder Construction Inc. and GeoPacific Consultants Ltd. conducted the design and construction of a deep soil mixed cut-off and retaining wall system. The “dry-box” solution was used to surround the excavation of an underground parkade and prevent flows of groundwater into the excavation."

Jan 1, 2016

By George J. Tamaro

In 1967 the Port Authority of New York and New Jersey undertook the construction of the World Trade Center (WTC) diaphragm walls, installation of the lateral support system and the excavation of the site, commonly referred to as the "Bathtub". The work took two years to complete. In 2001 the City of New York undertook the re-excavation of the site after the terrorist attacks. The recovery work will take eight months to complete. This paper describes the initial work on the WTC "bathtub" in the late 1960s and the recent work during the recovery.

Jan 1, 2002

By Danielle Nhanqulumanga, Pranith Bhatt, Snehal Patel, Khadeeja Priyan

The Bi-Directional Static Load Test (BDSLT) is a test that determines the capacity of piles when loaded under bi-axial static compression. In recent years the BDSLT has seen an increase in demand due to its safety, speed, and affordability. This innovative foundation testing method has been universally used over the last 50 years, however respective codes and standards have only been published within the recent years. Detailed test procedures and methodology are expatiated in the ASTM D8169 M-18 [1], and the IRC 78 2014 Clause 709.2.5. [2] These standards provide the minimum requirements for the execution of the BDSLT. In this paper we did a comparative study of both standards envisaging to bring attention to the similarities and discrepancies found therein, with an aim to highlight the impacts and challenges that differing provisions of each standard could pose on the conduct of the BDSLT. Discrepancies found have been explained on the basis of geotechnical engineering theories and relevant field occurrences observed by superior engineers. Additionally, we emphasize on the relevance of experienced engineer’s judgement when utilizing the standards.

Sep 1, 2022

By Pier Luigi Iovino

As Technical Director of the Naples, Italy based Fondedile, a geotechnical construction firm specializing in static restoration of structures, Fernando Lizzi, Ing., devoted over 30 years to the pursuit and advancement of static restoration and subsoil strengthening. Seismic events, construction of new structures on polluted and/or unstable soils in urban areas, and a need to carefully preserve and restore delicate, war-damaged historical structures, manifested the need for underpinning projects. Traditional construction methods and approaches, such as underpinning with additional foundation masonry, were not suitable and would have further jeopardized the stability of the structures. The introduction of the palo radice (root pile) revolutionized the field of underpinning. At the time of the first application of micropiles, the industry standard was driven piles. The drilled micropile was conceived and first implemented in the early 1950s, as an innovative means to underpin sensitive, historic structures and structures in urban areas. Specifically, the new construction technique was conceived as a less expensive alternative, designed to accept structural loads, be installed in limited access areas, in varied working and sub-surface conditions, which did not involve changing soil characteristics, and had minimal disturbance to the structure being underpinned, or to adjacent structures.

Jan 1, 2003

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Rodrigue Karam

An assessment of the geotechnical conditions at the Manhattan Cruise Terminals (Piers 88, 90, 92 & 94) was conducted after excessive settlement and structural distress was reported at Pier 92. The piers are located on the Hudson River along the west side of Manhattan, New York. The following paper focuses on the investigation and analysis performed on Pier 88 located at the western terminus of 48th Street. The pier is supported by approximately 2,500 timber piles bearing on soft organic silts and clays. The first portion of the analysis consisted of an offshore field investigation and laboratory testing to classify the subsurface soils within the project area and estimate the geotechnical capacities of the timber piles. Additionally, a settlement analysis including consolidation and negative skin friction analyses was performed to evaluate existing settlement levels. Axial and lateral analyses were performed to develop the soil springs (p-y, t-z, and q-z curves) necessary for the structural analysis.

By David Coleman

This paper presents a case history involving the installation of drilled in piles with rock sockets for the Bicycle and Pedestrian Path project located west of the Henry Hudson Parkway within the Riverside Park between 83rd Street and 91st Street at the Hudson River in New York, NY. The paper specifically addresses access and construction procedures for a marine installation when working in an urban and environmentally sensitive setting.

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

By Ronald D. Boyer

"Early in the design stage of Meadowlands Xanadu, the client’s project director informed me that “after construction, nobody is going to come to Xanadu to see the foundations.” My response was, “Well, that’s good, because the only reason someone would come to see the foundations is if there is a problem with them.” The client’s real message was clear: the money for the project would be better spent on architectural design components and interior finishes that would attract high-end tenants and entertainment seekers. The foundations, however, were challenging. The sheer size of the Xanadu development, the varying depths to rock, the loading conditions associated with the different structures, and the construction sequencing required the use of multiple deep foundation types and specialty foundation contractors. Xanadu, when completed, will consist of over 2.5 million sq ft of entertainment venues, restaurants and retail stores; America’s first i n d o o r s n o w dome; North America’s tallest (287 ft high) Ferris wheel; and four parking decks. Finished grades for Xanadu were essentially within about 1 to 2 ft of existing grades at the site, except for a 5 acre wetlands area, which received about 8 ft of new fill. Before the current construction, the approximate 75-acre Xanadu site was occupied by the Continental Airlines (now Izod) Arena, on-grade parking lots and the wetlands area. The Arena property is part of the New Jersey Sports and Exposition Authority (NJSEA) Meadowlands Sports Complex, which also includes Giants Stadium and the Racetrack, and is located in East Rutherford, N. J. Subsurface ConditionsThe site subsurface conditions include fill materials underlain by organic silt and peat (former marsh deposits or “meadowmat”), varved clay, glacial till and shale bedrock. The Xanadu site had been a marsh until the Sports Complex was created by filling in the early 1970s. The fill consists of dredged materials from Lower New York Harbor imported by hydraulic pipeline from the Hudson River. The fill also includes “historic fill,” defined as nonindigenous material deposited to raise the topographic elevation of a site, such as construction debris and other nonhazardous solid waste, and was generally encountered in thicknesses ranging from 8 ft to 18 ft. Within the previously developed portion of the site, a layer of marsh deposits consisting of peat and organic silt was encountered beneath the fill in thicknesses ranging from two ft to seven ft. Within the existing wetlands area, the marsh deposits were up to 10 ft below existing grade. The varved clay stratum was six ft to 36 ft thick. The depth to shale rock increases from approximately 15 ft near the west side of the site to approximately 80 ft near the south side. Groundwater was tidally influenced and varied from about 6 to 12 feet below both existing and proposed grade."

Jan 1, 2009

By Leonhard Weixler, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep ground-water barriers, named Cut-Off-Walls (COW). It can be anticipated that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Therefore, there is the demand to minimize the size of equipment to accommodate such projects. Following this demand, a new trench cutter system, the so-called CUBE System, was recently developed. The complete trench cutter system has been fit into container size dimensions so that it can work in very limited space conditions. In addition, complex conditions in terms of space limitations require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Due to the limited space requirements, the impact on the surrounding environment is limited. As the system is electric driven, an additional reduction of carbon footprint can be expected. First tests of the system have been carried out and the results will be shared. The paper will explain the construction process and the specific challenges and experiences made for these extreme conditions.

Oct 1, 2022