Search Documents

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Rachael M. Fischer, Daniel J. Woeste, Terence P. Holman

"A new 50 MW biomass renewable energy power plant was planned for construction in southwestern Georgia. The original foundation design consisted of very conservatively designed H-pile groups with vertical and battered piles to carry the axial and lateral loads. The authors conducted a testing program to value-engineer the foundations with the goals of increasing the working axial pile resistance and reducing or eliminating battered piles. Seven test piles were installed and dynamically monitored with a Pile Driving Analyzer (PDA). Two lateral load tests and one tension load test were conducted. The results of our testing program allowed the project team to: (i) increase working pile resistances by factors of 1.5 to 2, reducing the total number of piles by more than 30%, (ii) eliminate the battered piles, and (iii) lessen overall project risk. Poor communication and documentation in a critical area of the site required some piles to be spliced and re-driven after additional PDA testing, establishment of new driving criteria, and consideration of longterm soil setup. This case study emphasizes the economic and risk reduction benefits of a design phase testing program, and the need for consistent communication between parties in the field.INTRODUCTIONA new 50 MW biomass renewable energy power plant (Plant) was planned and constructed in southwestern Georgia. The Plant converts clean wood-based and paper-based waste from existing forestry and pulp operations, waste timber, and maintenance operations into steam that is used by an adjacent manufacturing facility. The Plant also generates electric power with limited greenhouse or particulate emissions for use by a local utility provider.The project site (Site) is located in Dougherty County, in the Coastal Plain physiographic province of Georgia; an area of known karstic activity. Specifically, the Site is underlain at depths of 30 to 45 ft by the Ocala Formation, a light-colored fossiliferous limestone of the Eocene era. According to Watson (1981), the Ocala Formation is 125 to 200 ft thick in the vicinity of the Site and increases in thickness to the southeast. Due to differential weathering, this formation is characterized by an irregular upper surface that transitions from sandy clay/clayey sand into a dense to very dense silt and fine sand locally referred to as limestone. This subsurface stratum is most relevant to the foundation design of the Plant."

Jan 1, 2016

By Kevin R. Johnson, Matt Caskey, Bryan Plaskett

Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical design and construction. These challenges can include constrained sites with limited access and laydown area, vibration concerns for adjacent structures, and the need to complete work within limited schedules. When challenging geotechnical conditions like variable bedrock elevations are present, the need to balance performance requirements with logistical constraints become the driving factor when selecting deep foundation systems. This paper focuses on the deep foundations used for a new elevated pedestrian bridge at a major health care facility in Tampa, Florida. In addition to the technical design requirements, the owner required a deep foundation system that could offer low vibrations, rapid production, and clean installation to limit impacts on their properties and the public roadway that separated them. The paper describes the project specific geotechnical and design conditions, describes Ductile Iron Pile design, and focuses on how installation of the system addressed the unique logistical challenges. In addition, the implementation of a full-scale load testing program to assess compression, uplift, and lateral design capacities is presented. This paper represents one of the few published references for Ductile Iron Piles on projects in the United States.

Oct 1, 2022

By D. Barber, A. D. Miller, P. A. Bray

The project was to develop an area within the existing West County Wastewater Treatment Plant which would enable the construction of a new Raw Wastewater Pump Station (RWPS) with a footprint of approximately 85 feet by 190 feet and a foundation depth of about 82 feet below grade and a new Short- Term Detention Basin (STDB) with a footprint of about 80 feet by 130 feet and a foundation depth that varied from approximately 3 to 24 feet below grade.. The excavation support system had to be designed to withstand both normal and the 100-year flood elevations. A Reinforced Soil-Cement Wall (RSW)was chosen to provide a hydraulic barrier which consisted of a single row of soil-cement elements installed along the perimeter of the area to be excavated. Steel wide flange beams were installed on 4 foot centers to support construction loads and be resistant to the lateral forces of the soil and hydrostatic pressures. The RSW was installed to a maximum depth of 104.5ft using a triple-auger drill rig with mixing paddles with a 2ft key into weathered shale providing a cutoff wall consisting of 53,150 square foot of treated soil. The project was to provide the initial design of the excavation support for the pumping station excavation support system and groundwater cutoff. There was 534 linear foot of soil-cement-bentonite wall installed and 106 - 80 foot long W21 x 121 wide flange beams installed on four foot centers into the alignment of the wall. Each element was drilled down into the weathered shale to obtain groundwater cutoff. Derek R. Guthrie Water Quality Treatment Center Pumping Package is the site for a new pumping station that will service Louisville, Kentucky residents. After unplanned long term exposure into the winter, the effects of freeze thaw cycles were evident.

Jan 1, 2017

By Nick M. Withers, Suthagarann Visvalingam, Cillian Mc Colgan

The level crossings removal project in Victoria is removing 75 level crossings across Melbourne to improve safety by separating trains from traffic, with other benefits such as reduced congestion, an upgraded road network, connected communities and support of urban regeneration. The level crossing at Station Street in Carrum forms part of the scope being delivered by the Southern Program Alliance (SPA), which is delivering level crossing removal works associated with the Frankston Train Line. At Station Street, a rail viaduct consisting of 19 spans and totalling approximately 545 m in length is under construction to remove the former level crossing. The viaduct consists of two parallel reinforced concrete Utrough girders and steel trough girders, one for each rail line. The foundations of the rail viaduct are founded on groups of Continuous Flight Auger (CFA) piles. The characterisation of geological units encountered at Carrum for the foundation design has been based on insitu testing and interpretation of test results from high strain dynamic pile testing (PDA) and Case Pile Wave Analysis Program (CAPWAP) from the Seaford Road Bridge, located approximately three kilometres South of Carrum, in similar ground conditions. By conducting pile load-deformation analyses based on pile testing significant savings were made for the client compared to the original design which was based on more traditional empirical correlations. This paper discusses the pile design methodology adopted using pile test data for this viaduct foundation. The results of this assessment are also compared to existing empirical correlations, and the limitations are discussed. The performance of the adopted pile design methodology using pile test data at Carrum rail viaduct is also discussed.

Nov 1, 2022

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By Masaru Sakakibara, Ngo Tuan Anh, Mitsuo Nozu

"In the southern region of Vietnam and the southern United States, numbers of Deep Mixing (DM) columns have been installed to increase the stability of slopes and mitigate ground settlement. However, in some cases, there were some quality problems for in-situ cement mixing such as inclusion of unmixed lumps. According to the investigations by the X-ray diffraction analyses, electrical conductivity (EC) test, and careful observations of in-situ mixing quality, it has been observed that the existence of expansive soil and its high EC value cause the insufficient in-situ mixing. The countermeasures to address these problems have been taken.INTRODUCTIONIn South Vietnam, under the guidance of numbers of references and standards (Miki, 1998, JGS, 2000, Kitazume et.al., 2001, BS 2005), Deep Mixing (DM) has been used in recent years for soft clay improvement to increase the stability of slopes and to reduce consolidation settlement (Nozu 2005, Tung et.al., 2009, S. T. G. Peng et.al, 2009). However, at the initial phase of the DM operation, the authors have encountered some unusual phenomena such as (1) lower strength and inclusion of unmixed lumps (Figure 1), (2) less amount of up-heaved soil, and (3) sticking of large lumps of clay to the mixing blades. In regard to the above (3), Photo 1 shows one of the countermeasures against the sticking. By means of the placement of additional plates, the stuck clay has been reduced significantly.Subsequently, we have noticed that the quality of DM columns has not been so good, which meant that there have been some unmixed lumps in the column despite high cement dosage such as more than 300kg/m3. The authors also have encountered the similar incidents in Vietnam and United States during the deep soil mixing work. For example, Photo 2 is the core samples taken from the DM test column in northern Vietnam adopting cement injection during penetration (CIDP) procedure. To solve this problem, various tests and investigations have been performed so far (Nozu 2010, 2012)."

Jan 1, 2015

By Joseph T. Coe, Alireza Kordjazi, Michael Afanasiev

Cross-hole sonic logging (CSL) is a common quality assurance measure for the evaluation of the structural integrity of drilled shafts. The results of CSL can be supplemented by a set of tomographic images generated by cross-hole tomography (CT). Although the same access tubes, sources and receivers are used in both methods, CT has the advantage of providing a higher quality image of the possible anomalies in drilled shafts. Nevertheless, it has been reported in literature that the CSL and CT miss anomalies with sizes of smaller than 10 percent of the cross sectional area of the drilled shaft. This implies poor resolution despite the high-frequency of the stress waves utilized in these methods. This issue with resolution can be at least partially attributable to the fact that CT relies entirely on the inversion of the first time of arrival and ignores the information embedded in the rest of the recorded traces. This study examines the application of full waveform inversion (FWI) to generate a higher resolution image of the possible defects in drilled shafts from the same data used for cross-hole tomography. FWI is a wave-field method that aims to directly match the recorded traces with traces obtained from a numerical model of the domain. This has the benefit of avoiding the selection of the first time of arrival, along with increasing the resolution of the final image due to extracting more information out of the traces. Through a series of numerical simulations, synthetic traces were generated from a drilled shaft with defects of known mechanical properties, dimensions, and location. These traces were then inverted to evaluate the performance of FWI for structural integrity testing of the drilled shafts. INTRODUCTION The presence of construction defects can compromise the structural integrity of drilled shafts and negatively affect their performance (O’Neil 1991; Sarhan et al. 2002; O’Neil et al. 2003; Poulos 2005). Several non- destructive testing (NDT) methods exist that are currently used for the evaluation of the structural integrity of drilled shafts. Cross-hole sonic logging (CSL), cross-hole sonic tomography (CT), and thermal integrity profiling (TIP) are well-established and documented in the industry and practical manuals (Brown et al. 2010). NDT methods prevent the need for coring and excavation and are relatively fast and cost effective. Successful implementation of these techniques has also been reported in the literature (Branagan et al. 2000; Iskander et al. 2001; Mullin 2010; Johnson 2016).

Jan 1, 2019

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative ?In-the-Wet? technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully implement this technology.

Jan 1, 2013

By George Piscsalko

Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By George Piscsalko

"Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.IntroductionDrilled shafts and Augered Cast-in-Place (ACIP) piles have been increasingly used over the past several years due to several reasons including the reduced noise and vibration, speed of installation for ACIP piles, and the large axial and lateral capacities which are attainable for very large drilled shafts. ACIP piles are drilled and cast without any visual inspection. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2017

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Dominic Ammon, Mark Rothbauer, Paul Landers P. E.

Across the Potomac River from the location of the DFI47 Annual Conference (October 2022), in Alexandria, VA, two large permanent anchored walls with a decorative shotcrete face were recently constructed for the North Hill project, a new multi-family and townhome development. The project was executed with a design-build approach for the Fairfax County Redevelopment and Housing Authority with review by the Fairfax County Geotechnical Review Board. The project was constructed in highly variable Potomac group sediments that include high plasticity clay/silt terrace deposits overlying coarser grained materials. The soils were over consolidated and exhibited potential for slickensides from relief of horizontal stresses from past erosion. The wall system was designed to include deep soldier piles and permanent long strand anchors considering past slope instability in the area. As the construction progressed, problematic soil conditions and water issues required modifications to drilling methods. The two permanent walls spanned 800 and 1,000 feet long with a maximum height reaching 40 feet.

Oct 1, 2022

By Bill Shea, Gordon King

"For a drainage channel built in San Juan, Puerto Rico, a value engineering (VE) proposal incorporating a secant pile top-down approach saved time and facilitated construction work on the larger flood control project. The channel, at the Bechara Industrial Area, Puerto Nuevo Port Facility and the Puerto Rico Maritime Shipping Authority Dock, was needed to allow drainage of the Rio Puerto Nuevo into San Juan Bay. The port area, one of the busiest in the Caribbean, has over 6,000 ft (1,800 m) of berthing wharves for ocean-going container ships along with over 500,000 sq ft (46,000 m²) of container loading and unloading areas, and is critical to the local economy.Planners wanted to minimize the impact of construction to the port and dock users, and developed a construction methodology and work sequencing that would prevent a complete barrier to port traffic. This plan involved non-contiguous and limited work area that “leapfrogged” along the alignment so as to prevent long barriers to lateral traffic movement across the culvert alignment.After reviewing the project plans and schedule, Morris-Shea Bridge Company (MSB) proposed an alternate design and construction approach that provided significant cost and schedule benefits, and also provided better access for the port and dock users. The alternate VE proposal involved top-down construction methodology and redesigned drainage culvert geometry with two parallel 2,000 linear ft (lf) (600 m) secant walls installed on each side of the culvert. These walls facilitated excavation and formed part of the culvert permanent walls. The result was a significantly reduced required construction right of way that allowed construction work in contiguous areas largely without impact on ongoing port activity. MSB conceived the design concept, and engineered design and construction of the VE alternate secant pile culvert.The project initially consisted of an open channel in the industrial area picking up water from the existing Rio Puerto Nuevo, transitioning to an enclosed culvert through the port and dock areas, and outfall through the existing dock. The base bid construction included three main areas of work:"

Jan 1, 2012

By Patrick J. Hannigan, Seth Robertson, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (―TLBT‖) and the conventional Bi-Directional Load Test (―BDLT‖) are full-scale static load test methods. In both methods, the test loads are applied bi-directionally to the deep foundation. The advantages of the conventional BDLT have been well established for cost efficient static load testing of deep foundations, particularly for large diameter, high-capacity drilled foundations. A conventional BDLT applies the bi-directional test loads using an embedded jack and bearing plates. The TLBT method also applies the bi-directional test load to embedded bearing plates but does so using reusable high-strength threaded bars attached to an above-grade hydraulic jack and load transfer assembly. The new TLBT method is well suited for load testing shafts of a moderate diameter, length, and nominal resistance or ultimate load. TLBT advantages include economic considerations resulting from the method’s reusable load application components and constructability considerations as it readily accommodates a center concrete tremie pipe or pump line location. This paper presents comparison results from full-scale load tests performed using both bi-directional load testing methods. Adjacent 3-foot diameter by 30-foot long BDLT and TLBT shafts were tested. Details regarding subsurface conditions and test shaft construction are included for the comparison of the TLBT and BDLT results. Corresponding test data and analyses for both test shafts are presented and discussed in detail. The BDLT shaft had a maximum uni-directional load of 240 kips at upper and lower bearing plate displacements of 0.5 and -3.8 inches, respectively. The TLBT had a maximum uni-directional load of 300 kips at upper and lower bearing plate displacements of 1.0 and -5.9 inches, respectively. These results as well as the load-transfer behavior and equivalent top loading curve results from the adjacent BDLT and TLBT drilled shafts are discussed. The paper also discusses the strain gage instrumentation on the TLBT load application bars and on the embedded bearing plates.

Oct 1, 2022

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017