Search Documents

By G. Chi, A. Solomon, J. Lai

"The Buffalo gold deposit is a small deposit consisting of auriferous quartz-tourmaline veins within a granodiorite stock in the Red Lake greenstone belt. This study aims to characterize the mineralizing fluids through fluid inclusion and stable isotope analyses and to compare them with those of the world-class Campbell- Red Lake deposit. Four types of fluid inclusions were recognized, including carbonic, aqueous-carbonic, aqueous, and halite-bearing aqueous, with the carbonic type being the most abundant. Raman analyses indicate that the carbonic phase mainly consists of CO2, with minor amounts of N2 and CH4, and rarely detectable H2S. The homogenization temperatures of the carbonic inclusions range from -41.7° to 30.9°C. The homogenization temperatures and salinities of the aqueous, halite-bearing aqueous, and aqueous-carbonic inclusions are 130° to 276°C and 9.7 to 23.6 wt.% NaCl equiv., 155° to 207°C and 32.9 to 42.3 wt.% NaCl equiv., and 215° to 357°C and 8.3 to 19.7 wt.% NaCl equiv., respectively. The d18OVSMOW values of tourmaline range from 8.2‰ to 9.0‰, and those of quartz from 11.4‰ to 11.9‰, with estimated fluid temperatures from 323° to 399°C based on the quartz-tourmaline isotopic geothermometer. It is postulated that separate CO2-dominated and aqueous fluids intermittently invaded the fracture/vein system in response to fluid pressure fluctuations, with limited mixing. The CO2-dominated fluid, previously recognized in Campbell-Red Lake as the main mineralizing fluid, is inferred to have been derived from deeper parts of the crust. This deep CO2-dominated fluid reservoir might have been a common source for gold mineralization in the Red Lake greenstone belt. Le gîte aurifère Buffalo est un petit dépôt composée de veines de quartz-tourmaline à l’intérieur d’un stock de granodiorite dans la ceinture de roches vertes de Red Lake. Cette étude vise à caractériser les fluides impliqués dans la minéralisation par les inclusions fluides et par les isotopes stables ainsi que de les comparer avec ceux du gîte de classe mondiale de Campbell-Red Lake. Quatre types d’inclusions ont été notes, incluant des inclusions carboniques, aqueuses-carboniques, aqueuses et aqueuses avec halite, les inclusions carboniques étant la variété la plus abondante. Les analyses par spectroscopie Raman indiquent que la phase carbonique consiste principalement en CO2, avec des quantités mineures de N2 et de CH4, et rarement avec des quantités mesurables de H2S. Les températures d’homogénéisation des inclusions carboniques vont de -41.7° to 30.9°C. Les températures d’homogénéisation et les salinités des inclusions aqueuses, aqueuses avec halite et aqueuses-carboniques sont varient de 130° à 276°C et de 9.7 à 23.6 poids.% NaCl équiv., 155° à 207°C et 32.9 à 42.3 poids.% NaCl équiv., et de 215° à 357°C et 8.3 à 19.7 poids.% NaCl équiv., respectivement. Les valeurs de d18OVSMOW pour la tourmaline vont de 8.2 à 9.0‰, et celles du quartz de 11.4 à 11.9‰, avec une température estimée du fluide entre 323° et 399°C sur la base du géothermomètre isotopique quartz-tourmaline. Il est postulé qu’un fluide riche en CO2 et un fluide aqueux distinct ont envahi le système de fractures/veines par intermittence en réponse à des variations dans la pression des fluides, et qu’il y a eu peu de mélange. Le fluide riche en CO2 est également observé à Campbell-Red Lake ou il est le fluide minéralisant principal, il est présumé être dérivé de portions plus profondes de la croûte. Ce réservoir profond de fluides riches en CO2 pourrait être la source commune des minéralisations aurifères de la ceinture de roches vertes de Red Lake."

Jan 1, 2009

By I. R. Muirhead, A. L. Craven

The trend in mining thermal coal is only to mine coal with the lowest sulphur content. In many coal seams, bands of coal with high sulphur content are often present, generally occurring either at the roof or floor level. Methods of selective mining are, therefore, necessary to recover only the low sulphur coal. This paper examines the methods currently in use in mines and the alternative methods that are able or have potential to offer control of shearers and continuous miners where greater thicknesses of coal have to be left in the roof and floor. These alternative methods rely on such characteristics as neutron gamma radiation; electromagnetic waves; vibration; infrared; infrared; optical; pick force; X-ray fluorescence; conductivity; gyroscopes and laser systems.

Jan 1, 2000

By Benedetto Corain

The production and dispersion of metal nanoclusters onto inorganic supports and amorphous carbon rest on well consolidated technologies belonging to the realm of industrial catalysis and of basic catalysis research (1). In spite of the existence of a variety of specific synthetic strategies, their very rationale relies on three main approaches i. e.: A: precursors of both the metal nanoparticles and of the relevant supports (or the support itself) are intimately mixed (even let to react) at ambient conditions and then thermo-reduced according to very controlled protocols (2); B: precursors of metal nanoclusters are let to be adsorbed onto suitable supports from the gas or liquid phase and subsequently thermally decomposed (3); C: metastable size-controlled metal nanoclusters are previously generated in a liquid medium and subsequently transferred onto pre-formed support particles (4). The production and dispersion of metal nanoclusters onto organic soluble supports is also a rather well documented academic praxis (5, 6, 7, 8) able to provide e.g. size-controlled Au0 nanoclusters of 4.4±1.7 nm (5). Our group started in 1997 developing (9) an innovative approach to the synthesis of metal nanoclusters dispersed inside insoluble, albeit accessible (see below) mechanically robust gel-type resins (10), which procedure was tested so far on palladium metal. Metal ions are previously dispersed upon ion-exchange inside of the polymer framework, followed by chemical reduction and by the aggregation of born metal atoms into nanoclusters, the size of which is templated (11, 12) by the three-dimensional intercommunicating meshes that build up the overall polymer framework (Figure 1).

Oct 1, 2003

By Tuula Mäkinen, Lauri Pesonen, Peter Björklund, Jouni Pihlasalo, Mikko Korpi

Outotec Direct Blister Flash Smelting technology has proved to be an efficient and environmentally friendly way to treat copper concentrates from the Zambian Copperbelt at Konkola Copper Mines' (KCM) Nchanga smelter in Zambia. The modeling of slag chemistry and thermodynamics with MTDATA software played a central role in deciding the operation parameters for the smelter. Outotec FSF Online Process Advisor is used to calculate the process parameters and to give valuable information of the process state for the operating personnel. The pre-calculated slag liquidus graphs are also integrated to the Online Advisor.

Jan 1, 2011

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Marc C. Bétournay

Hydrogen fuelcells are a known technology, having been applied to stationary (e.g equipment, buildings, power plants) and vehicle applications (e.g transit buses, space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and green house gas emissions. To date, however, fuelcells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuelcells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuelcell type of choice for the industry, the Proton Exchange Membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk. A small fuelcell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, INCO, the Ontario Ministry of Labour, Sandia National laboratories and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter as well as from shock and vibration provided to the unit in underground conditions, at INCO?s 175 Orebody minesite and INCO?s Stobie Mine. The test results provided will show that the unit was not affected by the underground conditions: physically and electrically the unit performed without any reduction in operation or adverse effects imposed.

May 1, 2003

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By F. A. McLean

At the Annual Western Meeting held at Blairmore, Alta., October 1924, the writer presented a paper drawing attention -to the advantages of portable gas-driven equipment for developing isolated mining properties. This type of equipment was at that time practically in its infancy and the details of results actually accomplished were somewhat meagre. During the last year or so a number of these plants have been installed so that it is now possible to offer more definite information regarding the actual mining progress accomplished with such plants and their cost of operation in various parts of the country. This paper has been written with the idea of reviewing the work done during the past year, and to supply data which may be of interest to those wh9 are confronted with the problem of selecting equipment for development or assessment work. Because drilling operations play such an important part in mining, one of the first problems that usually confront the prospective? mine owner is the selection of the proper com-pressed-air plant. The size and type of equipment and the method of driving it require careful consideration. The size and type of equipment is determined largely by the funds available, transportation facilities, and the speed with which the programme of development is to be carried out. The selection of the proper method of drive usually depends on local conditions, such as the relative cost of various fuels, and has an important bearing on operating costs.

Jan 1, 1926

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

By Eric Konigsmann

"Omai Gold Mines is a large scale open pit gold mining operation located in central Guyana, South America with a 12,000 tonne per day milling facility. Mill operations were initiated in December 1992 with commercial production beginning in January 1993. The entire operation employs approximately 120 expatriates and some 800 Guyanese nationals and is expected to produce in excess of 250,000 ounces of gold per year. The total mineable reserves contain 2.5 million ounces of gold with a projected mine life of twelve years.The milling circuits feature an SABC grinding circuit, gravity concentration and a conventional CIP gold recovery circuit. This paper will review the mill start up and ""run-in"" phase during the first year of operation. Emphasis will be placed on descriptions of start up problems and circuit modifications, mill performance trends in 1993, and personnel training and development. An outlook for 1994 is also given.IntroductionOmai Gold Mines is a large scale, open pit gold mining operation located in the Potaro district of Guyana, South America, some 160 kilometers south of the capital city Georgetown. Although there are numerous small scale gold mining ventures in Guyana, particularly with the dredging operations on the rivers, Omai is the first hard rock, open pit mine to be developed in the country. At present, this mining operation is one of the largest gold mines in South America.The Omai gold deposit has been exploited for over one hundred years. In the late 1800's, a German syndicate used hydraulicing with subsequent gravimetric separators such as sluice boxes and trommel screens to recover gold from saprolite, a soft, oxidized, claylike mineral which covers much of the claim area. Through the early 1900's and up until the 1950's, numerous mining companies including Anaconda Mining Co. Ltd. explored and drilled the Omai deposit but the technology and low gold price of the day made the reserve uneconomic to develop."

Jan 1, 1994

By A. E. Boone

"The paper presents critical areas in which improved coordination of effort by industry, government and sup-pliers will be essential to continue the growth record of the Canadian mining industry into the 'seventies'. The analysis includes: exploration, production, mining methods, research and development, markets, management and industrial relations. Performance objectives are suggested where tangible results can be measured. The author suggests the methods by which the 'seventies' can be the greatest decade in the history of Canadian mining. It is indicated that a national mineral policy is essential to the Canadian mineral industry."

Jan 1, 1970

By J. A. Meech, R. J. Tucker

"A dynamic computer model has been developed to simulate the operation of ore crushing plants. The model was created in a general form to allow imitation of a wide variety of secondary crushing circuits with only minor program modifications. The system can be run on either a microcomputer or a large time-sharing main frame computer as required.The size reduction and separation characteristics of crushers and screens are based on standard manufacturers' design and performance data. These calculations are isolated within various subroutines to facilitate tailoring of the model to emulate any particular plant of interest. Input and output data are presented in a variety of formats. Crusher, screen and conveyor amperages and surge bin levels can be presented in a tabular form along with appropriate alarms arising from improper circuit operation or process interruptions. Graphical representation of the circuit together with strip chart data output are features of the system when operated in a microcomputer environment.The program is currently being used at Queen's University as a teaching aid to demonstrate plant operating characteristics, control strategies and design concepts. The acceptance of, and reaction to the program at this level indicates a good potential for it to provide a valuable tool for operator training."

Jan 1, 1985

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002