Search Documents

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By D. W. Heard

Electrospark Deposition (ESD) is a low heat-input, high energy density, micro-welding process. The short pulse duration and high-pulse frequency, in combination with the small amount of material transferred during each pulse, results in the evolution of extremely rapid cooling rates, believed to approach 105-106 °C/s [1]. This rapid solidification event results in the refinement of the microstructure to the nanostructured or amorphous level [2, 3]. Figure 1 displays the resultant microstructure of an Al-17%Si alloy deposited by the ESD process. Furthermore, it was determined that the microstructure of the deposit remained unchanged after subsequent layers were welded onto the presented layer. Freeforming of materials is a rapid prototyping process in which the deposited feedstock is built-up to the desired geometry in a near-net shape manner. Figure 2 displays the automated set-up employed produce three dimensional freeformed objects via multiple deposition trials of the ESD process. The automated XYZ table is equipped with CNC software to transform CAD renderings into three dimensional tool paths. Figure 3 displays an Al-12Si freeformed gear (2" diameter, 12 teeth) produced by the ESD process, prior to removal from the substrate. An SEM analysis of the freeformed component showed that the microstructure did not coarsen during the deposition of subsequent layers during the freeforming process, as depicted in Figure 4, resulting in the production of a bulk nanostructured component. This paper represents a summary of the capabilities of ESD to fabricate advanced materials possessing refined microstructure. In particular, results on the microstructural evolution obtainable for various wear-related systems will be presented. In addition, the feasibility of using the ESD process to freeform three-dimensional objects via multiple deposition passes will be presented and accompanied by a characterization of the properties of the freeformed component. [1] R. N. Johnson, "ElectroSpark Deposition: Principles and Applications," in Society of Vacuum Coaters, 2002, pp. 87-92. [2] J. Milligan, D. W. Heard, and M. Brochu, "Formation of nanostructured weldments in the Al-Si system using electrospark welding," Applied Surface Science, vol. 256, pp. 4009-4016. [3] S. Cadney and M. Brochu, "Formation of amorphous Zr41.2Ti13.8NilOCul2.5Be22.5 coatings via the ElectroSpark Deposition process," Intermetallics, vol. 16, pp. 518-523, 2008.

Jan 1, 2010

By Jae-Chun Lee, Sadia Ilyas

We investigate the technical feasibility of bioleaching of metals from low grade sulphidic ore. Experiments were conducted with an adapted consortium of Sulfobacillus thermosulfidooxidans and Thermoplasm acidophilum in batch bioreactors (1.5 L), small columns (10 kg ore load, 8 % S0 sludge) and large columns (80 kg ore load, 12 % S0 sludge). Approximately 83 % Ni, 85 % Cu, 55 % Fe and 81 % Zn was leached out in batch mode while 93 % Ni, 89 % Zn, 81 % Cu and 65 % Fe was leached out in column reactors. Bioleaching potential improved by acid pre-leaching, adaptation of microbial consortium and periodic bleeding of effluents.

Jan 1, 2014

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By W. H. White, A. J. Sinclair

"Unaltered biotites from three samples of monzonite and gabbro from the Copper Mountain stock and a single sample from a pegmatic biotite-chalcopyrite vein cutting the Triassic Wolf Creek formation have a mean K-A age of 193±7 m.y. These data support a suggestion based on geological evidence that Copper Mountain ore deposits are related genetically to the Copper Mountain stock.A cogenetic mineral pair (biotite and clinopyroxene) from a sample of sericitized and chloritized monzonite of the Copper Mountain stock have identical K-A ages of 150 m.y., which probably represents a time of wide-spread, post-ore, hydrothermal alteration. This alteration is believed to be related genetically to a group of post-ore intrusions known as the ""mine dykes,"" suggesting that they also have an age of 150 m.y."

Jan 1, 1968

By Ian Thomson

OBJECTIVES OF EXPLORATION ? Prove/Disprove presence of potentially economic mineralization ? Keep on budget ? Minimize negative environmental impacts ? Gain a ?Social License to Operate? (SLO) WHAT IS A ?SLO? ? Granted by the local community ? Intangible, informal, non-permanent ? Has to be earned and then maintained ? Defined as ? Ongoing Approval (BSR and AccountAbility) ? Ongoing Approval, broad social Acceptance (Joyce and Thomson) ? Ongoing Acceptance (Nelson, and many others) ?Expression of the quality of a ?relationship?

May 1, 2010

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By R. D. Brown

In view of the many changes which have taken place since 1950 in the rules of the Income Tax Act concerning the deduction of exploration and development expenses, many corporate taxpayers each year face the tedious task of determining which particular rules their unclaimed exploration and development expenses are subject to and in what sequence these expenses are to be claimed. Recent amendments to the Act have cleared up some of the mystery of the "ordering" of these deductions. This article examines the sequence in which various categories of exploration and development expenses are to be deducted in accordance with the terms of the Act as amended by Bill C-11.

Jan 1, 1978

By Bert Taylor

"The Mining concessions of Quemont Mining Corporation, Limited, are located at 48°16'N latitude, 79°00'W longitude, in Rouyn township, northwestern Quebec. Six hundred and forty acres in area, they lie directly north of, and contiguous to, the Horne mine of Noranda Mines Limited. The north arm of Osisko Lake covers a large area of the southern part of the property. The orebodies lie below the Jake with one body extending through to the bedrock surface.The property was staked in 1922, and was originally known as the Murray Claims. The group attracted interest from numerous exploration companies because of the proximity of the Noranda orebodies.The United Verde Extension Company, of Arizona, optioned the claims in 1926. They sank a shaft to a depth of 235 feet, at a short distance from the Noranda boundary. From a level established at a depth of 215 feet they completed 3000 feet of exploratory driving from which 6000 feet of diamond drilling was done. Only a small body of siliceous gold ore was found before they dropped their ·option.In 1928, The Mining Corporation of Canada purchased a 90 per cent interest in the property. An operating company, later named Quemont Mining Corporation, was formed. An electrical survey was carried out on a portion of the property, followed by deepening of the shaft to 922 feet. Levels were established at 500 and 900 feet, and 4,800 feet of driving and more than 3000 feet of diamond drilling were carried out from them.Geological knowledge at that time recognized that a major break, the Horne Creek fault, lay not far inside the south boundary. Striking north 80 degrees east, the fault dipped south at 85 degrees. The rock on the north side of the fault was massive rhyolite; to the south, meta-diabase and a little rhyolite. A left-handed movement was indicated by a 600-foot offset on a north striking diabase dyke. The small body of siliceous gold ore, referred to previously, was confined to the 215 level."

Jan 1, 1949

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By F. E. Lee

The following outline gives a brief account of some of the ways in which microscopy is applied to the problems arising from the various operations of the Tadanac reduction works, at Trail, B. C. The Sullivan ore is a very fine-grained mixture of galena, marmatite, pyrite and pyrrhotite. The separation of minerals associated so intimately is a difficult task and requires careful control. Various oils and reagents are used in the process as developed, and it is essential that the operators have a means of control which shall be rapid, and at the same time, approximately correct. This result is obtained by microscopic analysis in the following manner: The operator places a quantity of the material upon a slide, a drop of water is added, and it is covered with a cover glass. Upon examination with transmitted light, the zinc mineral particles appear reddish, the ordinary gangue colorless, the lead and iron sulphides opaque. This method has proved of great assistance both in the development and in the operation of the present method for concentrating Sullivan ore. The miscroscope has thus become as much a part of the metallurgical equipment as the balance and burette. The microscope used in the laboratory is a Fuess "petrographic" with a specially-made vertical "illuminator" by Bausch & Lomb, with the usual accessories.

Jan 1, 1924

By J. E. Gill, A. R. Byers

The Surf and Pugsley gold-copper mines; owned and operated by Surf Inlet Consolidated Gold Mines; Limited; are about 6 miles inland from; the head of Surf inlet; on Princess Royal island; Skeena mining division; British Columbia. Surf inlet is a fiord 360 miles in an air line northwest of; Vancouver.

Jan 1, 1954

By K. G. Markkola

Since 2005, Compafifa Contractual Minera Candelaria (CCMC) has defined various strategies which aim to optimize the usage of the available energy in each of the SAG grinding circuit modules (SABC-A configuration). For this purpose, the use of larger size balls along with operating with an optimum balls/load ratio has been implemented. Additionally, in the ball mills, the amount of balls in relation to the equipment's usable diameter has been optimized. In the pebble crushing circuit, the percentage of material passing 12 mm (112 in) product has been increased by 15% by: (1) modifying the crusher mantle profile, (2) implementing a strategy for maximizing the power in each crusher, (3) using continuous improvement tools (Lean - Six Sigma), (4) redesigning SAG mills discharge grates, and (5) changing discharge grates in order to control the crusher feed size distribution profile. All these activities have improved plant throughput by 1,000 t/d with no significant capital investment. As part of the energy consumption optimization study, we have considered determining the optimum operational rate of each SAG mill, in relation to the mill liner life and also the improving the control strategy in conventional grinding.

Jan 1, 2007

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By Göckmann. Klau

"IntroductionCopper has been recycled ever since its discovery. Even in Graeco-Roman times recycling of this resistant, and thus valuable material was carried out as a matter of course. Just take, as an early example, the Colossus of Rhodes: after the figure collapsed during an earthquake, the bronze parts were melted down into ingots and sold.Copper is a material which can be recycled again and again because copper produced from recycling is not different from copper originating from primary materials. This is mainly due to electrolytical copper refining whereby not only the base metals but also the precious metals can be removed. In contrast, with aluminum and iron only the more electropositive elements can be removed by refining, and the resultant scrap must, therefore, be sorted mechanically into various alloys for subsequent smelting.The recycling rate for different base metals is given in Table 1. Despite this ideal prerequisite, the generally quoted recycling rate of copper of about 40070 appears rather low. However, it must not be forgotten that the recycling rate is defined as the ratio of the annually utilized quantities of copper scrap and the annual production figures (Table 2). Moreover due to the economic growth over the last 30 years the availability of copper from scrap materials is lower than its consumption because copper is principally employed in very long-life consumer durables and only returns to the recycling circuit after many years. The average time for the copper of some goods to be recycled is detailed in Figure 1."

Jan 1, 1992