Search Documents

By Libao Zhu, David J. Williams, Nazife Erarslan

"Statistics show that the drawbell in underground mines is usually subjected to significant damage by impact loading due to falling ore. Drawbell damage causes a large quantity of residual ore to remain on the drawbell, thus leading to a huge waste of ore resources. In this study, the Cavity Monitoring System (CMS) and Surpac software were employed to visualize the 3-D damage. Also, the Discrete Element Method (DEM) was employed to perform simulations of the falling ore to investigate the damage evolution of drawbells under repeated ore impact and obtain the dynamic damage accumulation mechanism. The reason of drawbell damage was found due to the micro-shear cracks. The numerical simulations of a drawbell damage process under repeated impact loading showed the main failure type was shear failure and this type damage was found increasing with more ore falling. INTRODUCTIONDrawbells are an important part of underground mines and play a significant role in ore recovery in terms of safety, economy and efficiency (Brunton et al., 2010; Hustrulid & Bullock, 2001; Trueman et al., 2002). In most cases, blasted ore is gravitated along the drawbell and finally arrives at the footwall of the drawpoint. However, some of the blasted oversize ore blocks clog the drawbell road and those ore pieces are called hang ups (Penswick, 1997). However, any damage on a drawbell is believed to be the reason for these hang-ups. In the literature, researchers have reported that the stability of the draw-point is influenced by the stress distribution above and near the drawbell (Butcher, 1999; Neverov & Neverov, 2013). Much research in the literature has been done on draw-points in underground mines. In fact, rockfalls cause very serious damage on a small impact area in a very short time (Volkwein et al., 2011). Hoek (2000) pointed out that the blasted ore causes progressive ravelling and even collapse of the drawpoint, thus the ore in the stope is abandoned. In this paper, the Cavity Monitoring System (CMS) was employed to obtain the damage profile of a drawbell due to the impact of rockfalls and to confirm the residual blocking ore on the damaged drawbell. Then, the drawbell damage evolution due to repeated falling ore was simulated by the Discrete Element Method (DEM)."

Jan 1, 2015

By I. Orford, V. Rozon

"The Sä Dena Hes Joint Venture Mill was designed to process 450,000 tonnes per year of ore grading 11.3% lead and 13.2% zinc.Run of mine ore is crushed in a jaw crusher and then ground in a closed circuit SAG mill and ball mill. A standard differential float in conventional flotation cells produces quality lead and zinc concentrates. Dewatering of concentrates is achieved using high rate thickeners, lamella clarifiers and pressure filters. Process water is 100% recycle.Plant design was based on metallurgical test work performed on drill core samples. The plant is operating at better than design specifications.INTRODUCTIONSä Dena Hes Joint Venture was formed in 1989 to develop the Sa Dena Hes lead/zinc sulphide mine, located approximately 45 km north of the Town of Watson Lake, Yukon. The mine is owned by a Joint Venture partnership between the operator, Curragh Inc. (87.5%) and Hillsborough Resources Limited (12.5%).The project was completed in a record ten months, working throughout the severe Yukon winter and through an abnormally wet spring and summer. The first truckloads of concentrate were shipped from the mine on August 1, 1991.The mill currently processes 550,000 tonnes of ore per year grading 6.9% lead and 11.5% zinc. Ore is crushed in a jaw crusher and ground to 60% passing 75 microns in a closed circuit operation of one SAG mill and ball mill. Using conventional flotation cells a 150,000 tonnes of concentrate is produced in a year with lead concentrate grading 78% lead and a zinc concentrate grading 60% zinc at overall recoveries of 89% and 90% respectively.Concentrates dewatering is accomplished using high rate thickeners, clarifiers and pressure filters. The lead concentrate and zinc concentrate contain 5.4% water and 7.8% water respectively. Concentrates are trucked to Skagway, Alaska for subsequent shipping to overseas smelters."

Jan 1, 1993

By J. Peck, M. J. Scobie, M. D. Pollitt

"IntroductionOne aspect of current research in the Canadian Centre for Automation and Robotics in Mining (CCARM) involves the automatic identification of different rock types based on particular drill performance parameter responses. In this paper, the four drill performance parameters of torque, pulldown pressure, rotary speed and penetration rate, were measured from an instrumented rotary blasthole drill during field investigations undertaken at the Fording River Mine, Elkford, British Columbia. The variations in these parameters were subsequently correlated with the corresponding rock types using the results from gamma, neutron and core logs in the same or adjacent boreholes. Work to date has sought to understand the relationships between drilling performance parameter variation and rock properties. Using the results of these studies, the present research is aimed at developing techniques whereby classical statistical pattern recognition methods are applied to drill data to permit the discrimination of different rock units. A monitoring system incorporating such a capability would greatly enhance the quality and amount of geological information on a per borehole basis while drilling. This data in tum could be used economically and directly towards explosive loading, geological exploration and reserve estimation. Background and PhilosophyThis work is an extension of equipment monitoring studies at the Fording River Mine. At this site over a two-year period, 5180 m of data was acquired on an instrumented Bucyrus-Erie 60R drill during routine production blasthole drilling. Throughout these studies, a 311mm diameter S8M Security tungsten-carbide tricone bit was used. The mine, located in southeast British Columbia, is a large-scale, open pit coal operation. The means of excavation revolves around a drill-blast-muck cycle and employs a standard shovel-truck system of transport. Four main rock types are present: sandstone, siltstone, mudstone and coal, with average compressive strengths ranging from 10 MPa to 150MPa respectively (peck 1989). However, based on the field studies, very few differences in terms of strength and compositional properties were seen between the sandstones and siltstones at the site. Therefore, they are referred to as sandstone/siltstone in all further discussions."

Jan 1, 1991

By Tony B. Szwilski

"The efficiency of operation and life of an advancing longwall coalface depends, to a great extent. on the face-end roof strata conditions and the stability of the gateroads. The factors that influence the rate of closure of gateroads are examined, in particular the gateside pack and the coal rib (crush) pillars. The performance of mechanized packing systems is briefly discussed. Gateroad deformation surveys were carried out at two coal mines to determine the influence of the rib pillar width on gateroad stability; also, the influence of the gateside pack on the immediate roof and floor strata is analyzed based on strata bed displacement measurements from instruments installed in the gateroad and pack-hole of a longwall advancing face operating in a thick seam (7.55 m). Concluding, an evaluation of the fac e-end systems examined is given and recommendations made f or the most suitable rib pillar width. face-end geometry and roof strata reinforcement.IntroductionKevword s: Coal mining, Pillars, Rib pillars, Ground control, Longwall mining, Gateroads , Packing systems, Roof control. The face-end region of a longwall advancing face is the center of mining activity, being the turn-around point for the coal cutting machine. and the place of gateroad formation and movement of special face-end supports. The design of face-end layouts can be aided by knowledge of strata control parameters, such as the effective loading of the immediate roof strata , convergence of the roof and floor, magnitude and distribution of fractures in the roof strata around the face-end , optimum placement of supports, coal seam thickness and strength characteristics, geometry of layout and interaction from neighbouring workings. Generally, the gateroad is formed by one of three face-end methods: (a) advanced headings, (b) in-line system (gateroad formed at the face) or (c) conventional ripping with or without stable elimination (also halfheading). The quality of gateroad is influenced principally by the face-end system employed, standard of gateside pack and width of pillar. A good standard of gateroad is generally achieved by employing the half-heading face-end system, the gateside pack and coal rib pillar having comparative support/ yield (stiffness factor) characteristics. However, the halfheading is often not favoured due to face operation restrictions."

Jan 1, 1981

By Marc Tardif

"The way alarm information is provided to an operator can make a huge difference in the minutes following an upset. Process alarms are often looked at as a way to help avoid catastrophic failure and serious accidents. But knowing that mineral processing is so energy consuming and that raw material is not consistent, all small upsets should also be seen as a catastrophe because they can have significant impact on product cost and quality.This paper will demonstrate how it is possible to use data from process alarms to provide operators with real time, value added information that will help them take the right decision at the right time and in turn, reduce unplanned downtime by 20 to 80% and incidents by up to 50% (number and cost),and optimize energy and capacity usage.In the era of Big Data, living in a world where we are submerged with information, one of the biggest challenges is to find the right information at the right time.Alarm rationalization projects will often focus on alarm quantity, but alarm quality is also very important. It is possible, by following a simple 6-step process to turn “alarms” into truly valuable information for operators. Based on known standards (ANSI/ISA 18.2 and EEMUA 191), this process will capture the knowledge of the best and most experienced operators and process engineers, and make it readily available to everyone, right on time, when it matters the most.INTRODUCTIONWhen spending some time in a modern control room, it is easy to notice the huge quantity of information that is available to the operator. Modern operation stations feature multiple screens with HD capability. These screens display information like process display, history trends, alarms and events list, maps with geo-located information, images from live cameras, etc. However, it is harder to assess whether all this information is really helping operators: Is all the information relevant? Are process screens overcrowded? Is the information easy to understand? Does the operator know what to do with all the information? Are there too many alarms?"

Jan 1, 2016

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. 's Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By Shinji Muraishi, Shinji Kumai, Yasutaka Kedo, Takashi Kambe

"Magnetic pulse forming (MPF) is one of the extreme high-speed forming processes. A metal sheet which is accelerated by electromagnetic force is collided onto a mold and fine and sharp details of the product can be obtained. The deformation mechanism of the MPFed metal cannot be understood only by the microstructure observation of the deformed metal. The deformation behavior of the metal should be investigated also by considering the local microstructure change with strain, strain rate and temperature change during deformation. Numerical analysis is an effective method to achieve this requirement. In this study, pure Al and Cu sheets were deformed by MPF. Impact velocity of the metal sheet was calculated by using ANSYS Emag-Mechanical. Based on the obtained impact velocity, the deformation behavior of the metal sheet was reproduced, and local strain, strain rate, and temperature were analyzed by using ANSYS AUTODYN. The relationship between the local microstructure change of Al and Cu sheets and the deformation parameters was examined.INTRODUCTIONMagnetic pulse forming (MPF) is one of the high-speed forming processes using electromagnetic force. Fine and sharp details of the product can be obtained, and springback after deformation is extremely reduced in comparison to the conventional forming processes(Psyk, Risch, Kinsey, Tekkaya, & Kleiner, 2011). Figure 1 shows a schematic diagram of MPF. A metal sheet is placed over the coil in the discharge circuit. The discharge current runs through the coil, and magnetic fieldis producedaround the coil. An eddy current is inducedin the metal sheet. Interaction between magnetic field and eddy current creates electromagnetic force. The metal sheet accelerated by electromagnetic forcecollides ontothe mold. Forming is completed in a few tens of micro-seconds.MPF is suitable for metals with a high electrical conductivity like Al and Cu.The MPFed metal may have characteristic microstructure because of high strain rate deformation."

Jan 1, 2018

By Jas. E. Thomson

"The Omega mine is in McVittie township in the Larder Lake area, Ontario. Production at the mine commenced in 1936, and, until the end of 1946, ore milled amounted to 1,558,604 tons, from which 207,074 oz. gold and 28,205 oz. silver, valued at $7,585,470, were recovered. The mine workings extend to a depth of 1,975 feet.GEOLOGYThe geology of the mine has been described in detail by C. P. Jenney (l) and the writer (2). The general geology and structure in the vicinity of the mine is discussed on an earlier page in this volume. The rock formations found in the mine workings are indicated on the accompanying plan and section (Figs. 1and2). They consist of an intermingled, south dipping complex of volcanics, sediments, and secondary talc-chlorite schists and carbonates. The carbonatized rocks, which are often referred to as 'dolomite' in the Larder Lake camp, are siliceous-carbonate replacements in the talc-chlorite schist zones. In places they contain green mica, probably fuchsite, and are cut by a stockwork of quartz veinlets and stringers. A stock of syenitic intrusives lies south of the mine workings.STRUCTUREThe main structural features are indicated in Figs. 1 and 2. The formations and orebodies have a pronounced southerly dip, which flattens with depth. The talc-chlorite schist and 'dolomite' zones are part of the Larder Lake fault or 'break' on which there appears to be very large displacement. Evidence throughout the district would indicate that the south side moved up and, in the case of the Omega mine, the thrust may have been distributed throughout the several intensely sheared zones. This slice faulting could account for the repetition of sediments and volcanics. An alternative possibility would be original interbedding of volcanics and sediments."

Jan 1, 1954

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words 'Maintenance' and 'Equipment' as follows: Maintenance shall mean the 'care of or 'the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By N. Maleki

Magnesium matrix composites are widely used in automotive and aerospace industries for achieving higher performance due to their light weight. The Mg2Si intermetallics compound in Mg/Mg2Si composite exhibits many excellent properties such as high melting temperature, high hardness, and low thermal expansion coefficient. However, under normal cast conditions, the primary Mg2Si phase exhibits coarse Chinese script or dendritic morphologies and the eutectic structures is very brittle resulting in the low ductility and strength of the alloys. Modification treatment is a very effective method to obtain fine microstructure and improve the mechanical properties of the alloys due to low production cost. In this investigation various amount of bismuth addition have been carried out on Mg?5wt %Si alloy to refine and modify the morphology of coarse Mg2Si in order to improve the corrosion resistance of the composite product. The effect of Bi content on microstructure of Mg2Si/Mg composite was investigated by optical and scanning electron microscopy followed by EDX analysis and X-Ray diffraction. In order to compare corrosion resistance of unmodified and modified specimens, Immersion test and potentiodynamic polarization (PD) were used. The results showed that by Bi addition, the size of primary phase Mg2Si was considerably reduced and the morphology was modified from a coarse dendritic shape to a polyhedral shape. The results also indicated that the corrosion resistance of Mg?Si alloys was improved by the addition of 1%wt of Bi due to the reduction, refinement and evenly distribution of Mg2Si phase. Indeed, both the morphology and distribution of Mg2Si intermetallic had a great influence on the corrosion behavior of Mg/Mg2Si composite.

Oct 1, 2011

By K-A. Adamson

If fuel cells and hydrogen are to become a mass market reality a substantial amount of further research and development needs to be undertaken. Work in hydrogen storage, production, the economics of all aspects of fuel cells and hydrogen, materials balances, and product integration are just a few of the areas that are under focus. Setting R&D targets, and providing R&D funding are therefore areas that are central to the long term development of the market, and areas in which a number of governments worldwide are highly active. Some governments, such as Japan and Korea, have set a number of very ambitious, highly focused, long term targets and are backing this up with substantial funding, others such as the EU are working on a more integrated approach, wrapping some fairly fundamental R&D into large integrated projects which run in combination with a number of other market aspects, such as public acceptance and roadmapping. The US is slightly different, in that although is has a number of long term programmes and targets, FreedomCar and SuperGen being just two, the levels of funding are set annually with the passing of each years Fiscal Budget. This paper takes three high profile regions and analyses the R&D targets and funding levels for fuel cells and hydrogen. Criteria that will be looked at include: Time frame of target(s), level of ambition, funding issues, including: Funding windows, levels available, funding barriers, overall programme goals. The added value to this paper is that it will provide a clearer picture of where each region is heading, what are its strengths and weaknesses, in terms of R&D and where there may be areas for potential international collaboration.

Jan 1, 2005

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By B. MohammadSadeghi, S. Bakhshivash, M. Haghshenas, F. Rahimi

"Spring-Back/Forward in sheet metals is defined as recovery of elastic strain upon unloading in a deformed sheet specimen. Since this phenomenon can cause alternation in the dimensions of a part, leading to irrecoverable compensations, the operative parameters need to be investigated, thoroughly. To assess spring-forward and effective bending parameters, V-shaped bending dies are the most commonly used experimental approach. In the present research, the effect of bending angle and punch tip radius on the spring-forward behavior of an Al-Mg-Si alloy sheet specimen is studied. To this end, a V-shaped die with four bending angles (i.e. 30°, 45°, 60°, and 90°) was designed and fabricated. Specimens with thickness of 2 mm were cut with dimensions of 50 mm×10 mm. Results show that by increasing the bending angle, the spring-forward angle decreases. In addition, smaller punch tip radiuses lead to further spring-forward. The effect of these parameters on the amount of spring-forward angle, strain distribution and homogeneity along sheet thickness was assessed using finite element analysis (FEA). Simulation results show that as the bending angle increases, the strain is developed more homogenously. Finally, micro-hardness test was used to study the effect of strain hardening caused by bending operation on strength evolution. Results show higher hardness trends for the zones in which the maximum plastic strain occurs.INTRODUCTIONPrecise production plays a significant role in the durability of a part. When it comes to sheet metal forming, this issue should be taken into account as an important factor. In order to predict the alternations, bending dies with special geometric parameters (i.e. V-shaped, U-shaped and L-shaped dies) are commonly used (Wagoner, Lim, & Lee, 2013)."

Jan 1, 2016

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016

By J. P. Rajot, H. Mouzannar, M. Bost

"The design of rock foundations may need to evaluate shear strength of rock-concrete interface by performing laboratory direct shear tests. A series of tests were carried out on specimens for different values of the spacing free of encapsulating material about the shear plane and different values of normal stress. Different kinds of failure were observed and not necessarily at the rock-concrete interface. The spacing free of encapsulating material appeared to be of significant influence on the test results. A mechanical analysis is presented which illustrate the influence of the loading conditions in the direct shear box on the failure mechanism. INTRODUCTIONThe design of rock foundations subjected to significant lateral loads requires defining the value of the shear strength of the interface between rock and cast in place concrete. Verifying the stability against sliding of strip footings subjected to inclined loads (SETRA, 2009) or concrete gravity dams (CFBR, 2013) are common examples where design modelling approaches imply the shear strength, sometimes the deformation behavior, of the rock-concrete interface, more or less assumed as a failure plane.Defining the behavior of rock-concrete interfaces relates to tribology. Many studies have been conducted to improve the representation of this behavior (e.g., Johnston & Lam, 1989; Kodikara & Johnston, 1994; Gu, Seidel & Haberfield, 2003; Saiang, Malmgren & Nordlund , 2005; Fishman, 2008; Eltervaag, 2013; Gutierrez, 2013), raising many questions. The behavior appeared to be influenced by many factors such as the geometry of the interface which is not planar, the roughness of the natural rock, the rock mineralogy and the concrete formulation. In addition, the study of the shear strength of rock-concrete interfaces involves considering the two different deformation behaviors of both rock and concrete. Finally, the observed failure mechanism is strongly influenced by the initial cohesion due to adhesion between the two materials when concrete is directly cast onto rock."

Jan 1, 2015

By G. Bimpilas, G. N. Anastassakis

"Today, one of the most intense problems in mineral processing systems is referred to the treatment of fine (–100 µm), and even smaller size, particles. Fine mineral particles possess specific properties (small mass, high specific surface area, and high surface energy per unit area) that render their separation inefficient with conventional methods (physical, physicochemical) and equipment. As a result, it is not feasible to obtain a concentrate both of high grade and recovery in mineral value and a considerable amount of mineral fine particles is lost to the tailings. As evidence, we could cite numerous examples from industrial practice with considerable loss of mineral values to the tailings because of the fine particles size, e.g. phosphate, tungsten, tin, etc.The objective of the current paper is to investigate the possibility to separate magnetic gangue minerals and rocks (serpentine, ilmenite, and olivine) from magnesite by co-agglomerating all the gangue components and subsequent magnetic separation of the agglomerates.To meet the target, hydrophobic agglomeration tests were initially carried out on single minerals to define the favorable conditions for selective hydrophobic co-agglomeration of the gangue minerals. In this respect, the effect of the following factors was examined: pH, collector dose, conditioning time, and settling time of the agglomerates. Among the combinations examined, the most favorable proved that with amine in the basic pH region. The use of non-polar oil proved beneficial. The preliminary results were confirmed by tests on mineral mixtures. The application of magnetic separation resulted in the removal of gangue minerals and the recovery of magnesite concentrates of commercial grade (magnesite content 95% approximately) and high yield.The current paper contributes to the development of mineral processing, since it successfully copes with a very important problem of mineral processing, such as the efficient separation of fine particles."

Jan 1, 2016

By J. M. Paxton, R. L. Roscoe, G. A. McCreary, W. W. Muir, T. J. Drown, D. A. Barr, T. W. Law

"This paper reviews the complete cycle of a small mining operation in a remote section of northern British Columbia, including discovery, exploration, development and production. The discovery of high-grade epithermal gold-silver mineralization occurred in 1969 following a regional geochemical reconnaissance program designed to search for porphyry copper mineralization in the Cassiar-Omineca Mountains. Exploration and development from 1971 to 1979 included geological, geochemical and geophysical surveys; trenching, almost 30 000 feet of surface and underground drilling in about 100 holes and cross-cutting, drifting and raising on the principal goldsilver- bearing vein. This led to the delineation of 100000 tons at an estimated grade of0.9 oz gold per ton and 18 oz silver per [on to an average depth of 120 feet below surface. of a 100-ton per day mining operation employing about 50 personnel with all supporting infrastructure transported to the site by a Hercules aircraft. The operation was subsequently supported by its own Twin Otter aircraft with periodic Hercules campaigns supplying major items including fuel.The mining operation included both open-pit and cut-and-fill methods. The milling operation employed conventional cyanide leach process with cyanide destruction initially by alkali chlorination and subsequently by the Inco SOl /Air process.The fly-in operation, initially structured on a 21-day-in and 7-day-out basis was modified to al-t-day-in and Z-day-out basis with no loss in efficiency and with a significant increase in employee satisfaction. The operation, which earned the B.C. Small Mines Safety A ward in two consecutive years in its Ll-month operating history, emphasized safety and process hazard awareness. Wildlife studies in the environmentally sensitive mine area also showed that industry and wildlife can coexist in harmony.Most importantly, the paper compares the feasibility assumptions with actual operating experience."

Jan 1, 1986