Search Documents

By T. E. Newkirk

In the past few years there has been considerable controversy on the most suitable material to be used in ventilation doors which will have to serve also as fire doors. For this reason it was thought useful at Mclntyre to find out to what extent our zinc chloride treated spruce doors were fire resistant and what protection we could expect in case of an underground fire. The doors to be tested were constructed of the same material as that used in our regular ventilation doors underground, namely, 2-inch tongue-and-groove well seasoned spuce. It is to be noted, however, that whereas the dimensions of the ventilation doors are 5 ft. by 6 ft., those of the test doors were only 14 in. by 17½ in. The treated doors were made up from lumber that l1ad been treated with chromated zinc chloride, as described in Mr. Keeley's paper. Two kinds of tests were carried out: a heat test and a flame test. An electric muffle furnace for assaying, equipped with a pyrometer, was used for the beat test, the furnace door being replaced by the wooden door to be tested. In the flame test, the door to be tested formed one end of a rectangular steel box in which was placed a large blow-torch. Air was admitted at the rear of the box. A pyrometer recorded the temperature at the inside surface of the door where flame impinged. The results of the tests are presented in the accompanying table, in which the word 'failed' is to be interpreted as meaning that the door had been damaged to the extent that smoke, but not necessarily flame, issued from its outside surface.

Jan 1, 1949

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By R. G. Achter, E. Wilson

"This paper describes the work undertaken to renovate the Pipe Open Pit drainage system, incorporating measures to improve effluent quality. It describes the technical feat of drilling an l l-inch-diameter hole from the bottom of the open pit for a distance of 1100feet to intersect an underground drift. An innovative method of checking the inclination of this hole is also described. The paper outlines the construction required on the 1500-foot level of the underground mine to facilitate water impoundment and slime settling, as well as the instrumentation for control of water flows. IntroductionThe Manitoba Division of Inco Metals Company operates two mines-an underground mine at Thompson and an open pit at Pipe. The Pipe Open Pit is located 20 miles southwest of the City of Thompson, approximately 400 miles due north of Win nipeg(Fig. 1).Surface diamond drilling of the Pipe ore body was sta rted in 1959. In 1961, a shaft was sunk to a depth o f 1,570 feet to carry out further exploration work and obtain bulk ore samples for metallurgical testing. Site preparation to mine the upper portion of the orebody as an open pit was initiated in 1966 and by late 1967, the removal of silt and clay overburden was in progress. The contractor completed the dredging in the fall of 1969. Over 12 million cubic yards of muskeg, clay and silt was removed, which in some places was 150 feet deep over the orebody. Production began in early 1971, by which time the top three benches of rock had been excavated and the orebody exposed.The Pipe No. 2 Mine main shaft was started in 1970 and completed in 1973 at a depth of 3,160 feet. Development for exploration purposes was carried out on the 1500 and 2460 levels, and permanent pumping facilities were installed.The surface dimensions of the open pit are 2,200 by 1,600 feet, with the long axis striking northeast. The walls are designed with a 45- to 50-degree slope and the ultimate design depth is 720 feet. The present depth of the pit is 520 feet and production capacity is 6,800 tons of ore per mine day."

Jan 1, 1980

By S. Theobald

Semi-finished copper and copper-alloy products are typically produced by casting, subsequent hot rolling or extruding and further cold working by rolling and drawing. The technological properties of the products depend not only on the chemical composition of the alloys but also on process parameters such as annealing conditions and degree of deformation. In each production step, measuring and control technology is an important tool for optimizing processes and ensuring constant high quality. This paper follows the product all the way from testing incoming scrap packages, chemical analysis of melts, mould level control in casting, non-destructive testing technologies in cold forming processes, controlling geometrical properties in the production process, to the final tests of technological properties. All test methods are focused on the applications and requirements of our customers, as the examples show.

Jan 1, 2007

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant’s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today’s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user’s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project’s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By David Minson

On many occasions, operators have seen that high density and paste thickener performance does not meet the initial design expectations, and the installed equipment produces lower than expected thickener underflow solids content. This lower-density tailings slurry leads to more water and lower beaching angles being seen at the tailings storage facility (TSF). This not only reduces storage capacity, but also increases the risks of non-compliance with environmental permit constraints. Reasons for the shortfall in performance can be many, but perhaps the main problem is inadequate understanding of the critical components of thickener design and operation, with too much reliance placed on standardised design terminology; such as tph/m2. This paper discusses additional factors that influence high-density thickener operation and presents test work that defines “Dynamic Slurry Fluidity”, “Bed Compaction Rates”, and “Natural Slump Angles” for these high yield stress/viscosity slurries. Finally, the paper uses this data to define thickener geometry, drive torque, floor slope(s), rake blade configuration and how this can be used to provide engineers with more tools for in depth evaluation of a High-Density thickener design. INTRODUCTION Generally copper mines are high tonnage operations, with copper flotation concentrators producing high volumes of tailings slurries of milled solids and water. As a result, Tailings Storage Facilities (TSF) become very large and this, along with potential scarcity of water, favours a design that maximises storage space. In theory, the use of filtration equipment that achieves immediate water recovery, high TSF in-situ densities and high stacking angles are preferred for this duty. However, large tailings filter units are uncommon, and have high operating and capital costs that favour the use of thickeners. The use of high-density thickeners to produce a thick or near-paste like slurry with high un- sheared yield stress values above 100 Pascals, is becoming more common. The higher thickener underflow is required to not only maximise water recirculation within the mill, but to also increase beaching angles, maximise tailings storage capacity and minimise evaporation losses arising from large areas of superficial water. However, the reliability of this equipment is also under scrutiny and there is perhaps a need to better define these designs.

Jan 1, 2019

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

"Line Creek Resources Ltd. produces three million clean tonnes per year of metallurgical and thermal coals for the international market. The mining operation, which is located in the mountains of southeastern British Columbia, produces coal from four pits by conventional truck and shovel methods.The South Pit, which has been in operation since J982, has a benched highwall 490 m in height. Shallow dipping coal seams at the base of the syncline formation will be exposed in the highwall over the next four years of pit life. The first of these seams, which will measure 500 m in final highwall length, was exposed in J994. An auger, powered by a 1250 hp engine capable of cutting 2.2 m diameter holes, was brought on site in J994 and has proven to be a successful means of recovering coal from the J3 m thick seam.This paper covers the background to the selection of an auger mining method to recover highwall reserves together with the geotechnical and methane considerations for this approach.IntroductionLine Creek Resources Ltd., a wholly owned subsidiary of Manalta Coal Ltd., owns and operates the Line Creek mine. The operation which consists of four active pits, a processing plant, and rail loadout is located in the southeastern coal fields of British Columbia. Figure 1 shows the general area.The coal bearing sequence at the mine is preserved on the east and west limbs of a major syncline. Up to twelve mineable coal seams, ranging in thickness from 2 m to 15 m are contained in the formation. Within the pits the seams are stratigraphically consistent and structurally undisturbed, except for small-scale thrust faults that create multiple repeats of the seams."

Jan 1, 1995

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By D. Kao, J. Gogal, S. Humphrey, T. Byrne, M. Davoodi

"High total and dissolved uranium values were noted in the process water at the Cigar Lake Operation (CLO) during early production start-up period, whereas significant levels of dissolved uranium had not been observed previously at similar operations. The excess dissolved uranium resulted in higher demands on the water treatment plant, along with higher operating costs, environmental risks and some unrealized revenue potential. A species balance indicated that uranium was leaching into solution in the grinding, dewatering, and storage circuits under normal operating conditions. Jet boring, water recycle, ball milling, and the use of Pachuca tanks for ore storage results in a highly oxidative environment, which is favourable to leaching.This paper will outline the testwork performed to identify the conditions under which the uranium leaches into solution and to determine required conditions for uranium precipitation. Maximum uranium leaching was found to occur under normal operating conditions (pH ranging from 7.0 to 8.5); testwork indicated that both lowering and raising the pH can significantly reduce the uranium leaching. Analytical results combined with the batch scale testwork indicate that the uranium solubility is associated with carbonate species in the ore. Uranium precipitation was maximized at pH values greater than 10.5 or less than 6, corresponding well to carbonate leaching and precipitation values from literature. Higher precipitation efficiencies were noted at high pH ranges.As a result of this work, a pH control system has been implemented in the Pachuca storage vessels and thickener prior to water treatment plant on a trial basis. Caustic soda is recommended for pH control due to ease of operation, economic viability and material requirements and downstream constraints."

Jan 1, 2016

By Peter N. Calder, Louise H. Michaud

"An interactive mine planning package has been developed to aid with the tasks involved in generating dragline mine plans. This package employs recent advances in PC-based,3D computer graphics and 3D geologic modelling. A Gridded Seam Model (GSM), capable of modelling rugged topography and multiple coal seams, including folding and faulting, is used to generate the geologic database This model is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal reserves and the removal of waste material.As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans and can allow for the evaluation of a number of mining options within a reasonable time frame.IntroductionThere are a large number of variables that must be taken into account during the development of a dragline mine plan. This is especially true when developing a mine in mountainous terrain, where there is a lack of continuity of the geology and topography over the mine site. Until recently, the complexity of dragline mine plans has prohibited the development of a universal mine planning package that is applicable to all geologic and topographic situations. The majority of the commercial programs that are presently available to facilitate dragline mine planning have been developed for specific mine properties or are limited in the coal geology and mining methods that they can simulate (Brown and Clifford, 1983; White 1983; White and Jones, 1984; Sadri and Lee, 1982; Dagdelen, 1979)."

Jan 1, 1993

By Karim Ramji

The extractive sector today faces growing social, legal and political risks (SLPs) from so many different stakeholders including national and local governments, name and shame groups, civil society and environmental groups, and the ?Occupy? movement. Beyond these stakeholders, there are the indigenous peoples who have growing legal, social, political and economic influence which can often determine the outcome of the Project. The development curve in the extractive sector from initial exploration to mine start-up has become longer, steeper and more risky and expensive as these SLPs have grown in scope and complexity. Even if a project is permitted or starts commercial production, its ongoing development and operations are also facing these SLPs. The continuous assessment of these SLPs and the strategy to mitigate for them has now become critical for every project in the extractive sector. A project will only be successful if it is able to obtain the legal permits to operate, then withstand any judicial reviews, and then also to be able to gain and maintain the Social License to Operate (SLO). Stakeholder identification, management and engagement are key risk-mitigation tools. This paper focuses on the growing influence that indigenous peoples are now enjoying and the impacts on the extractive sector. Indigenous peoples are a unique stakeholder group because their legal rights and interests to lands and resources, their aboriginal title and rights, are gaining more recognition. When indigenous peoples form alliances with other stakeholders, this simply adds to their growing momentum and leverage, and this can become a daunting challenge for the extractive sector. More due diligence is required by companies to understand and assess the challenges posed by operating in areas claimed by indigenous peoples. There is a real need for mining companies to develop an effective indigenous engagement strategy to address these challenges in order to successfully convert risks into opportunities. Early identification and engagement with the indigenous peoples is required and the goal should be to conclude an Impact Benefits Agreement (IBA) with the affected indigenous peoples. The real objective must be to develop a real and transparent relationship between the company and the indigenous peoples so as to gain and maintain the SLO.

Aug 1, 2013

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

By Peter McBride

Human excellence in all areas of endeavour is acknowledged and recognized. Establishing role models and spreading the word on best practices helps broader audiences. For on-the-job safety, recognition awards are a component of successful programs. In Canada?s mining industry since 1941, the John T. Ryan Safety Trophies initiative has contributed to the sector?s improving record in this area. The much sought after and rich in history John T. Ryan trophies are recognized symbols of safety excellence in Canada. The effectiveness of the Ryan safety recognition program in Canada has led to its export to other mining countries seeking to improve their overall safety performance.

May 1, 2008

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Andrew Neale, Len Anderson, Rob Perry

"P.T Freeport Indonesia's new SAG mill commenced operation in February 1995. The reclaim system consists of four apron feeders and a series of three conveyors. The feeders are used in various combinations and relative speeds to blend SAG mill feed. It was recognized during design of the control system that effective automatic control would require dead-time and gain compensation. The successful implementation of the Dahlin algorithm to provide variable dead-time and gain compensation is described and compared to Pl control.RésumeL'opération du nouveau SAG de P.T. Freeport Indonésie a commencé en Février 1995. Le système de réclamation du minerai comprend 4 alimentateurs à tablier et une série de 3 convoyeurs. Les alimentateurs sont utilisés dans une combinaison variée et à des vitesses relatives différentes pour mélanger l'alimentation du SAG. II a été reconnu pendant la conception du système du contrôle que le contrôle automatique demandera une compensation pour le temps de délai et le gain. L'implantation de l'algorithme de Dahlin a été un succès et ii est comparé avec le contrôle Pl.ResumenP.T. Freeport Indonesia inició la operación de un molino semi autogeno (SAG) en febrero de 1995. El mineral es alimentado desde cuatro alimentadores tipo apron feeders y una serie de correas transportadoras. Los alimentadores se utilizan en variadas combinaciones y velocidades para mezclar apropiadamente el mineral que alimenta al molino SAG. Durante el diseño del sistema de control se detectó que el control automático requería de un tiempo muerto y compensaci6n de ganancia. En este documento se describe la implementación del algoritmo de Dahlin, que ha sido exitosa y ha permitido proveer tiempos muertos variables y compensaci6n de ganancia. Ademas se hace una comparaci6n con el Pl de control."

Jan 1, 1996

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By Ahmad Abdollahi

Many factors affect mechanical properties of hypoeutectic Al-Si alloys. As examples the presence of impurities such as Mn and Fe due to the formation of intermetallic phases, additions of small amounts of alkaline earth metals and cooling rate in consideration of Si formation, they all have an impact on mechanical properties of hypoeutectic Al-Si alloys. In this investigation, the effect of Fe content into the specification range of A357 alloy, the addition of different modifiers consisting of Na, Sr and Ca for the alloy of A356 and different mounting techniques for separately cast test coupons of hypoeutectic Al-Si alloys using the lost wax method were studied. The results showed that using material with lower Fe content and addition of modifiers improve mechanical properties. Also different mounting techniques resulted in different mechanical properties.

Jan 1, 2004

By L. Gawlik

Since the beginning of the 20th century, coal has been the world?s main source of primary energy. In the last few decades, consumption of coal has gradually decreased in some European countries and elsewhere due to the introduction of other energy sources. Regardless, industry continues to use solid fuels for energy production despite of their association with carbon dioxide emissions (about 7 billion Mg). For global development going forward, it is important to estimate what level of energy consumption can be expected as far into the future as the next few decades. To answer this question, specialized global institutions such as the International Energy Agency, the World Energy Council, the World Coal Institute, the U.S. Energy Information Administration, the International Institute for Applied Systems Analysis, as well as oil companies (BP, Shell), conduct periodic forecasts of world energy consumption. The development of such forecasts is very complex because their reliability is influenced by many factors that are difficult to estimate, such as economic development, population growth, climate change, and public awareness. We are all aware that the global demand for electricity will rise significantly in the coming years as a result of anticipated population growth, industrial development, rising living standards, and the general development of civilization. The world?s mineable resources in 2010 were as follows: coal 665.6 million Mg, brown coal 195.4 billion Mg, oil 163 million Mg, and natural gas 185.5 billion m3. The annual global primary energy demand in 2008 was more than 12 billion toe (12,267 Mtoe). In 2006, electricity production in the world amounted to 18,921 TW?h. The structure of the primary energy mix in TW?h (2006) was as follows: coal 41.0%; natural gas 20.1%; nuclear fuel 14.8%; hydro energy 16.0%; liquid fuels 5.8%; and other renewable energy sources 2.3%. The European Union (EU) is one of the largest coal consumers in the world. In 2010, the EU-27 produced 396.1 million Mg of brown coal, and 132.9 million Mg of hard coal; 188 million Mg of coal was imported from outside the EU. The largest hard coal producers in the EU-27 are Poland, Great Britain, Germany, the Czech Republic, and Spain; major brown coal producers are Germany, Greece, Poland, the Czech Republic, and Hungary. For many years, the Polish energy sector has been based on domestic fuel sources ? hard coal and brown coal. The characteristic feature of the Polish balance of primary energy resources is a very high share of coal ? much higher than the world average. Pursuing the decarbonisation of the Polish economy may jeopardize Poland?s energy security, leading to a significant increase in electricity prices, which would hamper the country?s economic development. Price volatility and supply uncertainty are now the dominant features of the international markets for oil and natural gas. The high share of these fuels in meeting energy needs is the reason for unrest in many countries, including those in the EU. Under these circumstances, coal may become the stabilizing element of EU energy security.

Aug 1, 2013