Search Documents

By G. R. Peeling

The Mining Association of Canada launched the Towards Sustainable Mining initiative in 2004. TSM's goal is to improve the mining industry's performance by aligning its actions with the priorities and values of Canadians. The initiative currently includes performance indicators for four areas: tailings management, energy use and greenhouse gas management, external outreach and corporate crisis management planning. Over the past year, the association has been designing a performance assessment and verification system for these performance areas, as its members prepare to move external verification of their performance in 2007. The initiative and its evolution, as well as the challenges faced in developing a verification system applicable to an entire sector will be examined.

Jan 1, 2007

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By Z. D. Hora

Air hough diatomite is known in many parrs of British Columbia, deposirs of mineable size have only been found in the area between Kam/oops and Quesnel in the sourh-cenrral parr of rhe province. Ar Quesnel, commercial producrion has continued since 1950 from diatomite lenses up ro 35m rhick. OCCURRENCES of diatomite are reported from many parts of British Columbia, but deposits of mineable size are known only from the area between Kamloops and Quesnel. Only Quesnel deposits have yet reached the production stage. Commercial production dates back to 1950, and up until 1979 approximately 22,700 tonnes of diatomite had been produced. Most extracted diatomite was processed until 1980 by Crownite Industrial Minerals Limited in Quesnel to produce an oil absorbent and animal bedding. Smaller shipments are used to make insulating bricks on the lower mainland. Deposits near Quesnel extend 40 km along the western bank of the Fraser River from Quesnel to Alexandria; most production has come from Lots o. 6132 and 906. Di atomite is present as discontinuous lenses up to 35 m thick. Diatomite beds Industrial Minerals in Canada are of Upper Miocene age and are overlain by plateau basalts. Diatomite consists almost exclusively of Melosira granulara diatoms that are usually very small and mixed with variable amounts of clay, ilt and volcanic ash. In recent years, extensive beds of diatomite were identified near the confluence of the Chilcotin and Fraser rivers. Diatomite in this locale is a part o f the Upper Miocene to Pliocene Chilcotin Group of sedimentary rocks that are overlain by olivine basalt and related luffs. A deposit near Red Lake is situated 50 km northwest of Kamloops. Diatomite beds occur in the Tranquille Series of Eocene age and are similar in composition to those in the Quesnel area. The Red Lake deposit is abo ut 4 m thick but its areal extent is only a few tens of hectares.

Jan 1, 1984

By M. Mahdi Aboutalebi, Roderick I. L. Guthrie, Mihaiela Isac

"A preliminary computational fluid flow model has been developed to simulate the flow field of liquid steel in the mold region of billet mold casting. This study reports the effect of different Submerged Entry Nozzles (SEN) on the fluid flow in round and square billet, curved mold, casters. In this study, ANSYS Fluent 14.5 software was used to model the 3-D turbulent flow of liquid steel. The standard k-0 model was used to simulate turbulence in the mold region. Similarly, the species transport equations were discretized to simulate the dye injection test into the mold cavity. The behavior of flow in the mold region was validated against previous experimental work. Predicted results showed that different nozzle types plus the slight curvatures in the molds can significantly influence the flow patterns generated within the mold region, and thereby affect the finished quality of the billet products.INTRODUCTIONConventional Continuous Casting (C.C) processes are presently used to solidify more than 95% of the 1.5 billion tons of steel now produced in the world annually (World Steel in Figure, 2014). This overwhelming contribution of C.C processes for steel production is the prime motivation for this study, in order to understand and optimize the casting processes and thereby reduce internal defects and minimize energy consumption. The primary objective of all C.C processes is to maintain liquid metal purity during the casting process and to create a uniform flow within the caster so as to avoid internal and external defects. In this regard, studying fluid flows in the mold region of continuous caster has attracted many research groups, in both academia and industry, in recent years. The mold region is one of the most critical parts of the C.C. process, in which the transport phenomena associated with this region can significantly affect the quality of the final products. Thus, proper control of fluid flows within this region can be expected to greatly decrease both internal and surface defects such as Oscillation Marks (OM), inclusion entrapment, and Mold Powder Entrapment (MPE). In the casting process, the fluid flow in the mold region can be affected by a number of variables, such as; the flow control system (stopper rod or slide gate), nozzle geometry, SEN (Submerged Entry Nozzle) depth, casting speed, mold dimensions, gas injection, and the application of electromagnetic fields. One of the most influential and easily-changed fluid flows are the jets of steel issuing from the SEN. Nozzle geometries are variable, consisting of a number of exit ports, different port angles, and/or port sizes, the bottom shape of the nozzle, and the SEN immersion depth (Thomas, 2001). The SEN characteristics can markedly affect meniscus surface velocities, surface level profiles, and turbulence levels that can vary in terms of the frequency and the magnitude of their fluctuations."

Jan 1, 2016

By J. A. Muñoz

In this work, short and long-term tests were performed using different massive mineral sulfide specimens (chalcopyrite, pyrite, sphalerite, galena, covellite and chalcocite) of museum grade and quartz of analytical grade in an acid medium containing silver ions. After attack, the samples were observed by SEM and products characterized by EDS. Parallel, massive specimens of pyrite (FeS2) and chalcopyrite (CuFeS2) were embedded in an epoxy resin, either electrically isolated or in electrical contact, and treated with silver ions in the presence of bacteria. Finally, massive chalcopyrite and pyrite electrodes were subjected to electrochemical measurements in an acid medium under different experimental conditions (addition of silver ions and inoculation). The results showed that silver deposition takes place preferentially on specific mineral surfaces: chalcopyrite, galena, covellite and chalcocite. The chemical reaction of silver ions with pyrite and sphalerite was negligible at low silver concentration (8 ppm). But sphalerite reacted with silver ions at higher silver concentration (100 ppm). In a mixture of chalcopyrite and pyrite, silver was deposited on the former surface creating new cathodic sites which sped up the electrochemical reactions of chalcopyrite dissolution.

Jan 1, 2007

By A. Kobzhanov, S. Saparova, S. Brochot, D. A. Mango

KATCO (an ORANO Mining and Kazatomprom joint venture) is the largest in-situ leach uranium mining operation in the world, exploiting the Muyunkum and Tortkuduk uranium deposits in southern Kazakhstan. After extraction from the deposits, uranium is then transported via a hydraulic network to be purified in three processing plants located near these deposits. Within KATCO, with the support of ORANO Mining and CASPEO, in 2018 and 2019, a large project that had as its main objective to improve the uranium accounting system was implemented. The objective of this paper is to describe this project and all the changes that it entailed. At KATCO plants, a black-box approach was previously used for uranium accounting. However, it is recommended to use all the available measurements and to deploy a data reconciliation model (between well-fields and plant) as the reconciliation uncertainty is overall lower and it provides a more accurate uranium balance. During the deployment of this project, the rules and algorithms to generate the uranium accounting report, the associated flow diagrams (for uranium accounting), the streams, units of operation, stocks, reporting and Key Performance Indicators calculation rules were re-defined.

Jan 1, 2020

By A. A. Shirzadi, E. R. Wallach

"Liquid gallium has been used successfully to modify/remove the surface oxides prior to diffusion bonding similar and dissimilar nickel-base superalloys. Using this approach, bonds in nickel-base superalloys with ""virtually invisible interfaces"" were produced, and the compositions in the bond region were very close to those of the bulk alloys. Room temperature tensile and bend tests showed no preferentially failure at the bond lines. Creep tests on samples made between two different Inconel alloys also showed failure away from the joint, i.e. in the parent metal of the Inconel alloy with lower creep resistance. The high temperature lifetimes of these samples were as long as those of the unbounded Inconel, confirming that the joining approach has no adverse effect on the nickel-base superalloys being joined."

Jan 1, 2006

By Stanley Davidson

"This description of the structural geology of the Beattie mine has been condensed from a more comprehensive paper published previously (4).The property is in western Quebec, a short distance east of the Ontario boundary on the extension of the so-called Porcupine belt into Quebec.According to the geological surveys of the Dominion and Provincial Governments the regional structure in the vicinity of the mine is an easterly pitching, overturned syncline with several thousand feet of Timiskaming sediments in the centre surrounded by Keewatin volcanics (1, 2, 3).The mine lies on the north limb of the syncline, and the Keewatin series in this locality is, with few exceptions, overturned, dipping steeply north and facing south.The mineralization is closely related in space, and possibly genetically, to a body of syenite porphyry intruded into the Keewatin series along the north limb of the syncline. No ore has been found very far from the syenite or related lath-porphyry dykes, and the largest orebodies are composite, consisting of bleached and brecciated volcanics ( primarily tuffs) adjacent to altered syenite porphyry, both silicified and mineralized with very fine pyrite and arsenopyrite. In addition there are important ore shoots following a fracture zone within the syenite."

Jan 1, 1954

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012

By W. R. Bacon

"IntroductionTHIS IS a brief discussion of certain regional and economic aspects of the Coast Range of British Columbia. Between Portland canal and the 60th parallel of latitude, only the eastern margin of the Range is in Canada. The solely British Columbia interval extends from Portland canal to Burrard inlet. Personal observations in various parts of this area form the basis for much of this paper.Regional GeologyGranitic RocksSome of the best, most continuous exposures in the Coast Range are found at sea level. Reconnaissance study of the coastline has shown that the Range is predominantly granitic in character, but there simplicity ends, for the term 'granitic' as applied to the Coast Range covers a variety of mineralogical compositions. Actual granite is quite uncommon, occurring mainly in irregular or dyke-like masses that do not achieve batholithic dimensions. It is commonly pinkish, relatively homogeneous, and exhibits few of the deformational features that are obvious in much of this plutonic complex.Most of the granitic rocks of the Range fall well within the compositional limits of quartz diorite and granodiorite. The problem of resolving the great mass of these rocks into smaller coherent units is in general a difficult one. As noted above, granitic rock of uniform composition and texture is found in restricted areas and can be outlined without much difficulty. One such body occurs on the southern shore of Nelson island."

Jan 1, 1955

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By Lev Filippov, Saeed Farrokhpay

"Flotation process has had less success to recover nickel from laterite ores. Nickel in laterite ores is often finely disseminated in various minerals in very fine size. Therefore, fine grinding should be used to liberate nickel containing particles. Particles resulted from fine grinding are often very fine, and recovery of such particles is generally low using conventional flotation methods. One option to overcome this problem is enhancing the particle-bubble interaction by increasing the particle size and forming flocs. Selective flocculation of fine particle can be therefore the key to enhance the flotation performance of low grade laterite ores.INTRODUCTIONThe majority of the world’s nickel resources occur as laterite ores which are complex, low grade and expensive to treat using conventional smelting and high temperature and/or high pressure autoclave methods (Xu et al., 2013). While about 70% of the nickel resources are contained in laterites, only 40% of the world’s nickel production comes from these ores. Researchers have tried to improve the nickel laterite flotation recovery by using a number of feed preparation techniques. For example, in a study on a laterite ore sample from Australia, flotation tests on a narrow sized fraction of 38-75 µm resulted in only a small increase in the nickel content, from 1.0% to 1.4% (Quast et al., 2015a). In fact, no physical separation technique (including flotation) has been able to dramatically upgrade nickel in laterite ores (Quast et al., 2015b). Thus the challenge of processing low grade nickel laterite ores still exists. This paper aims to explore the possibility of applying selective aggregation in pre-concentrating of valuable minerals in nickel laterite ores."

Jan 1, 2016

By Curtiss O. Ehrsam, M. Naseem Mian

Alaska’s Red Dog Mine is strengthening its position within Cominco’s “Vision 2000”strategic plan by continually improving quality and quantity of production while reducing costs. Red Dog has evolved into a stable and mature operation, after six years of milling experience. A high grade, partially oxidized orebody in the severe Arctic environment, along with competing producers in a volatile metals market, are the continuing challenges facing Red Dog. The Red Dog Mine is striving to meet these challenges with emphasis on operator training combined with creative systems development and increased production. This paper describes developments in operations along with future plans.

Jan 1, 1996

By G. H. Faye

The prospect of obtaining high-grade concentrates from Canadian pyrochlore ores is rather unlikely, and experimental beneficiation pro-cesses ?appear to have yielded products in the range of 3 to 20 per cent N&apos;b205? A possible solution of the problem is to find an economical chemical method for recovering high-purity Nb2?05 from such concentrates. A technically feasible but economically unproved process is outlined in this paper, in which the concentrate is decomposed by an acid attack and the oxides of niobium and tantalum are isolated and then separated by liquid-liquid extraction. The solution of the ore is adjusted to 7 M HF-5 M HNO3 and the niobium and tantalum are extracted from this solution with methyl isobutyl ketone. The mixed oxides of niobium and tantalum are recovered from the oxdanic phase and dissolved in 0.5 M HF-1.0 M HNO3. Tantalum is extracted preferentially from this solution with methyl isobutyl ketone, leaving niobium in the aqueous phase. By the use of this process it is possible to produce niobium pentoxide and tantalum pentoxi.de in 99.5 per cent purity with a recovery of approximately 95 &apos;per cent, under lab-oratory conditions.

Jan 1, 1957

By Mark W. Masson, David B. Stevenson, David W. Broughton, Douglas R. Cruji, Steven E. Parry

"Abstract-The Amalgamated Kirkland gold deposit is located at Kirkland Lake, Ontario, within the Archean Abitibi Greenstone belt of the Canadian Shield. It lies on a fault or "break", termed the Cyprus Break, which is a splay off a regional structure termed the Cyprus-Battle Mountain Break. The Cyprus Break merges with the Cyprus - Battle Mountain Break above the -250 m level, as it was not encountered in shallow drilling or surface exploration. These structures lie 1.5 km south of the 727 000 kg (23 million ounce) Kirkland Lake Main Break and 0.5 km north of the 872 000 kg (30 million ounce) Larder Lake Break.The deposit is hosted by alkalic Timiskaming Group volcanic and sedimentary rocks which are overthrust by older Larder Lake Group tholeiitic and komatiitic flows along the Larder Lake Break. Timiskaming syenitic intrusives, similar to the host rocks for the Kirkland Lake Main Break gold deposit, intrude both suites.The Amalgamated Kirkland deposit consists of lode-style gold mineralization which is mainly hosted by altered and pyritized Timiskaming trachytic volcanics which wedge out or thin at depth, between two sedimentary units. The intersection of the Cyprus - Battle Mountain and Cyprus Breaks, in conjunction with the westward plunge of the volcanic wedge, appears to control the westerly plunge of the Amalgamated Kirkland deposit at approximately 50º.Mineralization is characterized by blue-gray brecciated and "wormy" quartz-ankerite veins which contain up to 10% fine-grained pyrite and, in decreasing order of abundance, minor galena, chalcopyrite, sphalerite, molybdenite and visible gold. The sulfides and gold commonly occur along fractures and wallrock inclusions within the veins. Native gold occurs as fine pinpoints distributed in 1-mm to 5-mm size clusters of up to ten or more grains.The auriferous veins occur within a quartz-ankerite-sericite-pyrite alteration assemblage which is enveloped by a broader zone of ankerite-sericite±hematite±quartz-pyrite alteration up to 60 m wide. This latter assemblage overprints the regional greenschist-facies chlorite-calcite assemblage.The Amalgamated Kirkland property has had a long history of exploration activity beginning with the first discovery of mineralization in 1911 on the Hunton Shaft claim located in the northeast corner of the property. Since that time various prospecting, mapping, trenching, geophysical surveys and diamond drilling programs have concentrated on either carbonate zones along the Larder Lake Break or quartz veins along the northern side of the property in association with complex trachyte flows and syenite dikes.Battle Mountain Canada Inc. located the Cyprus - Battle Mountain Break through a prospecting, trenching and geophysical program in 1989. Drilling by Battle Mountain and Cyprus Canada under the surface showing, coupled with several revisions to the structural interpretation of the Cyprus - Battle Mountain and Cyprus Breaks, resulted in delineation of the Amalgamated Kirkland deposit. Location of an auriferous structure through basic surface exploration within 1 km of a world-class orebody demonstrates both the subtle nature of Archean gold deposits and the potential for finding new mineralization in heavily prospected camps."

Jan 1, 1995