Search Documents

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By Bish Chanda

In the minerals business, like any other commodity-based business, management faces the daily challenge of holding down costs while the real prices of products are continually falling on an inflation-adjusted basis. Since the marketplace sets the prices, often without any premium attached for product quality, being one of the lowest-cost producers is the most viable competitive strategy. Continuous improvement is the mantra that can make the difference in terms of long-term survival of a mining company. Yet, this message has not always been followed, especially during periods of prosperity ushered by high commodity prices. More often than not, the need for improvement is only triggered by a crisis. This may be caused by events such as the onset of a severe economic recession, a prolonged oversupply situation due to an optimistic expansion of capacity during the period of prosperity, or simply falling profits alerting management to bring costs under control. At that time, there would be a need to implement a new cost-saving program, bring in a consultant to find ways to reduce costs, or re-activate an old program that had been shelved for some time.

May 1, 2003

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013

By Howard W. Tipper, Richard B. Campbell

"The Quesnel Trough is underlain by a thick sequence of mainly Upper Triassic and Lower Jurassic volcanic-clastic and sedimentary rocks that lie between the highly deformed Proterozoic and Paleozoic rocks in the Omineca Geanticline to the east and the Upper Paleozoic Cache Creek Group in the Pinchi Geanticline to the west. Broad areas of the Trough between Kamloops and Williams Lake are covered by Eocene volcanics and sediments and by Miocene-Pliocene plateau lava. Granitic intrusions were apparently mainly confined to two major episodes; one about 200 m.y. ago (coeval with the Guichon batholith) and one about 100 m.y. ago. In addition, the region includes small granitic and syenitic intrusions, some porphyritic, that may be all or partly still younger. Exposures in the region are generally small and scattered, obscured by widespread, not necessarily thick glacial deposits. This, together with the extensive Tertiary cover, makes prospecting difficult. The part of the Quesnel Trough discussed here is the direct northwest-ward extension of the copper-rich Kamloops-Merritt-Princeton region. It contains the Boss Mountain molybdenum mine, related to a breccia zone induced in a batholith of the oldest group by a younger intrusion, and the Cariboo Bell copper deposit in Lower Jurassic volcanic-elastic rocks and syenitic intrusions. The Gibraltar deposit, in a 200-m.y. intrusion, is within the Pinchi Geanticline close to the margin of the Trough. Molybdenum prospects are mainly restricted within or near the 100-m.y. granitic rocks. Copper prospects, on the other hand, are most prominent in the volcanic-elastic rocks and in the 200-m.y.-old granitic rocks, although they can also be spatially related to younger intrusions. Copper thus has a wide potential distribution.The writers believe that the region is deserving of careful and comprehensive exploration by directly applying the knowledge and techniques developed in the important producing areas to the south. All of the major pre-Tertiary geological elements seem to have potential for mineral deposits; none should be ignored. A thorough knowledge of the thickness and distribution of the Tertiary rocks and the development of geophysical methods to ""see through"" them is of particular importance."

Jan 1, 1970

By A. K. Debnath

Coal is the mainstay of Indian energy supplies. The many-fold increase in demand for coal puts a huge pressure on augmenting production, primarily from opencast mines. The increase in production necessitates heavy blasting in overburden and coal benches of opencast mines, which poses numerous challenges in carrying out blasting operations techno-economically. Presently, the consumption of industrial explosives and accessories in Coal India Limited (CIL) has touched a whopping figure of $350 million USD per annum and CIL will be spending approximately $1 billion USD between 2012?2013 to 2014?2015 for procuring explosives and accessories. This paper discusses some of key challenges faced in various mines of CIL during blasting, where blast instrumentation at the mine level will prove to a harbinger for practicing blasting engineers. Presently, the problem of scattering in surface detonators and down-the-hole detonators affects the blast performance significantly by increased blast induced ground vibration and reduced fragmentation. The paper discusses a case study carried out at Umrer opencast project of CIL to investigate the effect of scattering by using blast simulation techniques (i.e., JKSimblast) and observing the actual blast results with the help of a high-speed camera and multi-channel high frequency data acquisition systems. The fragmentation assessment was carried out by adopting Digital Image Analysis techniques and using the granularity software viz. Wipfrag. The blast instrumentation in the case study mine resulted in improvement in fragmentation of 12.76% and a direct savings in explosives cost of 28%. Geophysical techniques such as the seismic survey method have been used at Umrer Project, CIL to characterize the rock mass using the Multi Channel Analysis of Surface Waves system for selecting the explosives technoeconomically. The minimum deck thickness for mines of CIL using drill cuttings as decking materials should be 10 D, where D is the drill diameter. The estimation of blast performance on the basis of prescribed Powder Factor (i.e., kg of explosives per m3 of rock) is technically unscientific as the criterion of a good blast depends on many factors (i.e., good heave, loose muck, muck profile angle, ease of digging, uniform fragmentation). The present paper proposes a new methodology for techno-economic evaluation of blast performance. The new methodology involves four significant factors viz. specific energy consumed by the loading equipment, charge factor, productive yield and diggability index for assessing blast performance. The use of user-friendly, accurate, reliable, rugged and handy instruments in blasting will significantly improve mine productivity, equipment efficiency and economics. The improvement in blast performance, even by 1%, will provide a significant savings of $3.5 million USD per annum to CIL. It may be concluded with high degree of confidence that blast instrumentation at the mine level will influence the mine productivity and economics.

Aug 1, 2013

By Kristie D. Tarr

Ideally, in situ monitoring would supply the input data for numerical modeling of backfill material property requirements. However, clue to production requirements and costs of conducting field tests, input data are often based on small-scale laboratory tests. The size of test samples is known to play an important role in the laboratory assessment of the behaviour of geotechnical materials, including backfill. There are observed differences between the mechanical properties of laboratory-scale samples and those of in situ materials, and these are generally attributed to the differences in scale. Various scaling factors have been proposed for converting laboratory observations to anticipated in situ conditions for soil and rock materials. With regard to mine backfill, very limited studies exist which have involved the effects of sample size on material properties. The literature indicates that reported backfill strength data are based on a variety of test sample sizes and in some cases, specimen geometries. Carefully determined laboratory scale effects could play an important role in estimating the potential backfill behaviour in the field, especially when developing new backfill systems. Laboratory studies were conducted with sample diameters ranging from 50 to 300 mm. Scale factors relating specimen size to strength were developed wherever possible, and are presented in this paper

May 1, 2008

Cominco began investigations about ten years ago relative to noise abatement in underground operations. As a result of intensive research, this study has advanced so that the practice now has wide application. Automotive mufflers are used on vane-type blasthole diamond drills. Exhaust hoses are attached to longhole percussion drills. Hand-held drills, such as airlegs and stopers, are equipped with mufflers which are either part of the drill, as received from the manufacturer, or are light rubber de-vices developed, fabricated and installed by Cominco. Ear defenders are in general use. The paper reviews details of practices employed, and assesses the success achieved. Noise is generally associated with some of the basic equipment used in mining. About ten years ago, in order to improve on this situation. The Consolidated Mining and Smelting Company of Canada Limited began investigations relative to noise abatement in its underground operations. As a result of intensive research, this study has advanced to the point

Jan 1, 1964

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By T. J. Fee

Introduction The International Nickel Company have been pioneers in mine rescue work in Ontario. Following the fire in the Hollinger mine in the spring of 1928, the Company purchased ten self-contained oxygen breathing outfits, ten all-service gas masks, an oxygen high-pressure pump, life line, inhalator, ten cap-lamps with batteries, and a complete stock of spare and accessory parts. An instructor from the U.S. Bureau of Mines, Pittsburgh, came to the Creighton mine for one week and trained twenty men in the use and limitations of all equipment. Monthly training courses were commenced in the fall, and have continued to the present time. Of the original twenty men trained, ten are still on the Creighton mine rescue teams. In the meantime, and as an aftermath of the Hollinger fire, the Work-men's Compensation Board of Ontario and the Ontario Department of Mines established a central mine rescue station at Timmins. This was completed in the spring of 1930. It was then decided, in view of the great expansion in mine development in the Sudbury district, to build and equip a similar station to serve all the mines there, namely, Creighton, Frood, Garson, Falconbridge, Sudbury Basin, and Errington. An extensive survey was made and a central location selected opposite the Frood mine. The International Nickel Company donated a site, and the station was completed in the fall of 1930. The station is a two-storey brick building, 27 ft. by 47 ft., with a large garage adjoining it. The ground floor is used for equipment and for training the crews. On the second floor are living quarters for the superintendent and his family. The garage houses a closed truck, in which all necessary equipment can be taken to any desired point for training purposes or for actual mine rescue work, if and when necessary. The garage is also used as a gas room, where the men are trained in an irrespirable atmosphere. A gas-tight observation window between it and the training room enables the superintendent to see and direct the men undergoing training, weight exercisers and other devices being used.

Jan 1, 1935

By H. E. Johnston

There are currently a number of options in terms of plant feed comminution tests: Bond work index tests, JK drop weight and SMC tests, SPI, low impact crusher work index tests, to name a few. However, information regarding specific energy requirements for regrind mills is often requested, which can be difficult or very expensive when only a small mass of concentrate is produced from bench-scale flotation tests. This research was aimed at developing a test methodology that would produce a similar result as an IsaMill Signature Plot but require less sample mass allowing for preliminary estimates of regrinding power at a lower cost. Initially, the laboratory test methodology was completed on a single sample in comparison to the IsaMill Signature Plot for that sample. Results indicated a very good correlation between the laboratory tests and the IsaMill Signature Plot for this sample, though some parameters did impact laboratory regrind mill efficiency. The developed methodology is subsequently being applied to a range of concentrates, investigating a range of material particle sizes and material types, in comparison to a full IsaMill Signature Plot on the same sample. This new test procedure has been called ‘The Eliason Test’.

Jan 1, 2014

By A. Scheltema Beduin, M. Kalisch, E. Floch, R. J. Dijkhuis, H. J. Oterdoom

In metallurgical copper production, the traditional aim is to increase recovery of copper to the maximum. SMS Siemag (SMS) has supplied numerous furnaces for this application. New targets are to make sure end of line products are as safe as possible with respect to health and environment, and to maximize raw material utilization. This means a for example a minimization of leachable metals in slag, so it can be safely used as a construction material, and either a targeted concentration or fixation of volatile compounds, such as arsenic. Currently, 2 process routes are generally applied for slag cleaning. The first is grinding followed by flotation, and the second is slag cleaning in an (electrical) furnace. Popularity of both options has fluctuated over the years, and currently the milling-flotation seems to be the more popular option. In this article some of the advantages and disadvantages of both methods are described, and especially how long term environmental policies could have an impact on the decision which process route to choose. Finally, this article will describe some of the developments SMS is working on in pyrometallurgical slag cleaning that could influence the direction for the design of the copper plant of the future.

Jan 1, 2014

By W. Wallace

The aerospace industry celebrated 100 years of powered flight in 2003, and the remarkable achievements that have occurred during the past 100 years are in no small way due to major developments in materials. Modern alloys for airframes, engines and other major sub-systems have evolved through the intelligent application of new processing concepts involving melting, casting, hot and cold working, heat treatment and more recently vapour phase processing. Alloy design has evolved in parallel to allow maximum benefits to be achieved from these processing advances. However, the pace of development seems to be slowing and future gains are likely to be made by learning how to extract major value from aerospace assets. Understanding the modes of deterioration and establishing cost effective lifetimes by holistic life cycle management seem to be the way of the future. Extending component lifetimes by repair, rejuvenation and refurbishment are all viable possibilities and they offer great opportunities for Canada, which, traditionally, has been a major user of modern aerospace materials rather than a supplier. The challenges for metallurgist, physicists and engineers will be no less than in the past and should create new business opportunities for Canada. The scenario described above will be developed by calling upon examples drawn from the author's experience.

Jan 1, 2004

By H. F. Zurbrigg

"The Frood-Stobie Mine is by far the largest metal producer in the Sudbury area. Its efficient development was made possible by the consolidation of three mining properties that covered parts of the same ore body. They were known as the Frood Mine, the Frood Extension, and the Stobie Mine.The southwest or Frood portion of the orebody was discovered by Thomas Frood and A. J. Cockburn in 1884. Cockburn's interest was acquired by J. H. Metcalf and W. B. McAllister and patents were issued to Frood, Metcalf, and McAllister in 1884. The property was purchased by the Canadian Copper Company (lnco) in 1886.James Stobie discovered the northeast or Stobie part of the orebody in 1885. In 1886 Stobie and Rinaldo McConnell applied for the location and patent was issued in 1886. They sold the property to the Canadian Copper Company (lnco) the same year.The Frood Extension property included very little of the ore zone at surface but it covered ore down the dip from Frood. Frank Cochrane was granted title to the property in 1908 and sold it to the Mond Nickel Company in 1910. The title was transferred to the International Nickel Company in 1929 at the time of the Inco-Mond merger.Prior to 1930 the three properties produced a total of about 1 ,000,000 tons of ore from mining done during the periods 1887-1903, 1913-1915 and 1925-1929. Since 1929 the Frood-Stobie operation has produced more than 120,000,000 tons of ore, about half from open pits and half from square set and blast hole stoping. The current production rate is in excess of 6,000,000 tons per year.The principal products from the ore are nickel and copper. The by-products are iron ore, cobalt, platinum, palladium, rhodium, ruthenium, iridium, gold, silver, selenium, tellurium, and sulphuric acid."

Jan 1, 1949

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By G. F. Flaherty

THE property of Tashota Goldfields, Limited, in the Lake Nipigon area, Ontario, is located about 4 miles west of Onaman lake and 16 miles by winter road south-southeast of Tashota station on the transcontinental line of the Canadian National railways. The mine, formerly developed to a limited extent under the name of Tashota Gold mine, has, since late in 1933, been under the management of Minefinders Limited, who, in 1935, brought it into production on a 60-ton per day basis. During the winter of 1934-35, the writer was geologist at the property. The geological structure in the immediate vicinity of the mine workings lends itself well to analysis on the basis of the mechanical principles of folding. Since structure is of prime importance in the localization of the ore-shoots and of the host shear-zones at the property, the correlation of all structural details and their mechanical interpretation forms a working hypothesis of structural control for the direction of exploration and development work. It is believed that the structural relations here set forth may be found applicable in part, or at least suggestive, in working out the relations of ore-shoots to structure in the Sturgeon River area to the south, and in the Little Long Lac area to the southeast (Figure 1).

Jan 1, 1936

By John Emery, George Wang

Research and applied utilization activities for the increased use of ferrous and nonferrous slags in construction are presented. The overall use of blast furnace slag is relatively well known for a range of construction applications from aggregates to slag cements. In contrast to blast furnace slag, which is volumetrically stable and straightforward in its construction uses, steel slag contains hydratable oxides that can result in volumetric instability that must be dealt with through appropriate steel slag aging, testing and quality control to ensure its appropriate use. Particular care must be taken to prevent potential steel slag expansive behaviour in confined applications. Quality requirements and guidelines on steel slag expansivity to further the use of steel slags, with demonstrated acceptable performance, are outlined. There is a full range of proven construction uses - from aggregate to cementitious materials - for copper, nickel and phosphorus nonferrous slag. The use of air-cooled nickel slag is presented, based mainly on practical highway construction experience. It has been shown that air-cooled, crushed nickel slag can be an excellent aggregate in granular base, engineered fill and hot-mix asphalt. There is a good potential for increased ground, granulated copper and nickel slags use as supplementary cementitious materials that is being developed, which takes advantage of the 'latent energy' content. The scope of a new technical text in preparation on the technology of slag utilization is reflected throughout to provide a practical context for the engineer.

Jan 1, 2004

By A. Piche, J. Nantel

"This paper describes the recent developments in Canada toward the establishment of a Canadian Centre for Mining Automation and Robotics, at McGill University and École Polytechnique in Montreal. The role of the Mining Association of Canada (MA C) and of the National Advisory Committee on Mining Automation will also be reviewed. IntroductionIn order to remain competitive, the mining industry must increase its productivity and reduce its costs. In the last two decades, this objective has been achieved through mechanization. From now on, any further improvement in productivity will be gained through increasingly more automated mining equipment.Recent international developments following the Versailles Economic Summit in June 1982, having given rise in Canada, to a renewed interest in applications of robotics and automation to mining.The mineral industry in Canada is at a crossroads. Competition in emerging from everywhere: lower grade ore bodies, increasing distances between viable mines and markets, third world massive production of certain commodities, substitution of "" space age"" materials (ceramics, plastics, composites, etc.) for metals.On the positive side, it is generally believed that present mineral commodities, i.e. base metal, gold, iron, industrial mineral s, etc ., will continue to be in high demand for centuries to come despite substitution. New applications for conventional metals will be found and the enhancement of certain properties of these conventional metals mean continued demand. For some mineral commodities, there will never exist an y substitute."

Jan 1, 1988

By P. E. Fox, R. S. Cameron

"The QR gold deposit lies in the Cariboo plateau region of central British Columbia. The deposit was discovered in 1977 and since then a mineable reserve of 1.3 million tonnes grading 4.7 g/t Au has' been outlined in three separate zones. Soil sampling of glacial tills followed by diamond drilling of favourable host rocks proved to be key exploration techniques.The deposit is situated in the southern Quesnel terrane along the eastern fringe of the Intermontane Belt which here comprises a sequence of basic and intermediate volcanics and a series of stocks of alkaline affinity; generally diorite, monzonite and syenite. Hornfels and epidote-rich ferromagnesian exoskarn and sulphide-rich mantos have developed in a metamorphic aureole formed around a central diorite stock. Gold-rich zones lie along the outer periphery of the aureole where bodies of gold-bearing epidote-rich skarn and auriferous mantos rich in epidote and pyrite have formed in beds of calcareous tuffite lying at the top of a thick basaltic sequence. The deposit is regarded as' a subclass of gold skarn deposits. Diagnostic features are its association with alkalic intrusive rocks in a subvolcanic setting and the presence of oxidized, epidote-rich mineral assemblages.IntroductionThe QR gold deposit lies within the Cariboo plateau region of central British Columbia, 58 km southeast of Quesnel. The deposit, owned by Kinross Gold, was discovered during a regional reconnaissance program by Dome Exploration (Canada) Limited and Newconex Canadian Exploration in 1977. Considerable exploration and development has been done since that time. Mineable reserves of 1.3 million tonnes grading 4.7 g/t Au have been outlined to date in three zones."

Jan 1, 1995

"AbstractThe Sedimentary Basin area of Western Canada, which lies between the Precambrian Shield and the Cordilleran mountain area, covers approximately 800,000 square miles. Sediments ranging in age from Cambrian to Tertiary are present and, of these, horizons in the Upper and Lower Cretaceous, Jurassic, Mississippian, and Devonian have yielded commercial oil and gas flows. Producing horizons in the Cretaceous and Jurassic are sandstone, while all those of the Palaeozoic are carbonate rocks such as red limestone or dolomite (bioherms). Shows of oil and gas have been encountered also in the Cambrian and Triassic sediments.The broad structural features of this vast expanse of sedimentary rocks are the Moose Jaw syncline, the Sweet Grass-Battle River arch, the Alberta syncline, the Foothills belt, the Rocky and Mackenzie mountains, the Great Bear-Slave Lake basin, and the Mackenzie Delta Basin area.This contribution outlines the .stratigraphy and structure of the Basin area, and gives examples of present producing oilfield structures and stratigraphic traps.Part 1.-Regional StratigraphyIntroductionThe vast expanse of relatively undisturbed sedimentary rocks of western Canada has long been recognized as prospective territory to search for oil and/ or gas. This search in western Canada dates back before the turn of the century, but, considering the size of area to be explored and tested, the effort an<l money expended upon it, which, before the recent discovery of oil at Leduc, Alberta, appeared large and fruitless, now seems almost ridiculously small. A check-up of effort and money expended prior to and since the Leduc discovery would undoubtedly reveal that more wildcatting and development has taken place during the last two and a half years than during all previous years combined. The figures would astound not only the average citizen, but many within the industry itself."

Jan 1, 1950