Search Documents

By V. Ramachandran

The successful advent of solvent extraction (SX) reagents for copper recovery and improvements in electrowinning of copper to produce LME grade A copper cathode have paved the way for the hydrometallurgical treatment of copper oxide and low grade sulfide ores. This has resulted in about 25-30% of the world's copper being produced today by the Leach-SX-EW process. The obvious next step was to develop processes for the hydrometallurgical treatment of copper sulfide concentrates, as an alternative to a typical smelter-refinery complex. The current paper updates the processes that have been developed to date with emphasis on processes that are being commercialized or that are seriously under consideration for commercialization. Most of the discussions relate to the hydrometallurgy of chalcopyrite concentrates, which account for about 70% of the world's known copper reserves. In summary, in the last thirty years, the hydrometallurgical treatment of copper sulfide concentrates has attained full maturity and will be a serious option to contend with while evaluating any future new copper plant.

Jan 1, 2007

By A. Brown

THIS P APER has been pre-pared as a progress report on Mines Branch investigations into problems of ground stress in certain co al mines of Western Canada. As such, it should be considered as a companion report to the one ( 1) presented to the Mining Society of Nova Scotia in 1956 and which dealt with similar investigations in the coal mines of Eastern Canada. For the past 50 years, dynamic incidents in the form of 'bumps' and 'outbursts' have been occurring in the coal mines of the Inner Foot-hills belt of tl1e Canadian Cordillera. As these phenomena generally become more frequent with in-creased thickness of overburden, a limiting depth of mining of 2,500 feet has been set (2) for estimating recoverable reserves of coal. If such a view were accepted, from a long-term viewpoint very large resources of coking-grade ?coal -in a part of the continent deficient in such coals -would not be available to the nation. The terrain in which these in-6dents take place may be described in geological terms as being dominated by pronounced structure in strata ?consisting of a large proportion of highly indurated rocks. The Geological Survey of Canada has co-operated by carrying out structural studies (3) at the mines, supplemented lithological by stratigraphic observations.

Jan 1, 1958

By T. D. Traubert, J. T. Dietz, D. Catena

"Canadian process industry experts have often observed the strong trend for U.S. industrial safety and environmental laws to creep across the border. These experts will be interested in new United States (OSHA) regulations (29 CFR 1910.119), and anticipated new U.S. Environmental Protection Agency (EPA) regulations that will require over 28 000 U.S. refineries and chemical plants employing more than three million workers, to begin a comprehensive Process Hazard Analysis (PHA) of these complex plants immediately. Impending EPA regulations are expected to expand these efforts and add process Hazard Frequency and process Hazard Consequence reviews for many additional industrial locations.These regulations were created to reduce catastrophic industrial accidents, and emergency releases of hazardous chemicals which endanger employees, the public, and the environment.Accurate, and field verified Piping and Instrument Diagrams (P&IDs) are essential to permit a meaningful Process Hazard Analysis or emission release to be done. Today accurate P&IDs often do not exist. Many companies that have started to update their old P&IDs have found the process to be far more difficult, time-consuming,and expensive than they ever thought.This paper describes a new technique of computer drawn ""Intelligent"" P&IDs that can make a Process Hazard Analysis less expensive, more accurate, easier to perform, and provides lasting benefits to the plant owner long after the PHA has been completed."

Jan 1, 1993

By David J. T. Carson

"The metalliferous deposits of Vancouver Island have generally been assigned to the Mesozoic ""Coast Range Orogeny."" However, a metallogenic study by the writer has revealed that several important classes are early or middle Tertiary. Included are porphyry coppers, and gold-quartz, arsenic and copper-arsenic veins.The porphyry coppers and many gold-quartz veins are within and adjacent to Oligocene-Eocene quartz diorite intrusive complexes. Arsenic and copper-arsenic veins have a close spatial relationship to sills and laccoliths of Oligocene dacite porphyry which intrude the late Cretaceous Nanaimo Group.Other deposits of demonstrable Tertiary age include a molybdenum stockwork related to a relatively potassic Eocene plug and a few small copper-skarn occurrences. Some copper stockworks and a mercury deposit are probably also Tertiary.The copper deposits of previously recognized Tertiary age are those of the Sooke area that occur in Eocene basalts and Oligocene gabbros."

Jan 1, 1969

By J. B. Mawdsley

"AbstractThe uraninite-bearing deposits in the Charlebois Lake area of northeastern Saskatchewan are unusual and important concentrations of uranium. They were first discovered in 1949 and preliminary development work to the end of the 1951 field season indicates the probability that this will become •another uranium producing district. The deposits are in zones bordering granite masses. These zones are of migmatite (mixed rocks) composed of calcium-rich meta-sediments intruded and replaced by a fine-grained white pegmatite. Locally this pegmatite is replaced by an end fraction which is relatively rich in fine-grained disseminated uraninite; it is these occurrences that constitute the bodies of economic interest.The fine-grained white pegmatite contains plagioclase feldspar more lime-rich than that in the granites of which it is an end differentiate. This extra lime, evidently derived from the intruded sediments, would result in the raising of the temperature of crystallization of the pegmatite-forming magma, thus consolidating it rapidly near the granite contacts as a fine-grained pegmatite. The end liquor containing uranium was evidently locally concentrated in minor fracture zones in these pegmatites. Where no lime sediments were present. the coarse-grained alkaline pegmatites were formed. Their crystallization would not be accelerated and the uranium would tend not to be localized in the pegmatite but to migrate and consolidate at lower temperatures with the end products, possibly in some instances as pitchblende veins."

Jan 1, 1952

By H. B. Lumsden

This paper is intended to deal merely with the commercial development of some of the principal non-metallic mineral resources in the three prairie provinces- Manitoba, Saskatchewan, and Alberta. Coal is not included in this summary. Building Stone First and foremost, mention may be made of the building stone now being produced at Tyndall, Manitoba. This is a mottled limestone and is declared by experts to be one of the finest building stones in America, both as regards durability and appearance. It has been used very extensively both for exterior and interior work, not only in western Canada, but also in the principal cities as far east as Montreal. The stone is the "'Upper Mottled Limestone", which forms the summit of the Trenton (Ordovician) strata in the Lake Winnipeg basin. Quarries are at present being operated at Garson and Tyndall . The area where this stone is known to be available extends in a north and south direction for a distance of three miles, and the main productive ridge is probably about one half mile wide. The outlook for the future of the industry is extremely promising, as the stone is becoming increasingly popular in Eastern Canada, more particularly for interior work.

Jan 1, 1928

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By C. Zangerl, T. Strauhal, S. Perzlmeier, M. Holzmann

"In high mountainous regions, deep-seated rock slides are often observed in foliated metamorphic rocks such as paragneisses, micaschists and phyllites. Given that comprehensive investigations of deepseated rock slides are extraordinary costly and therefore are rare, most studies are related to investigations in the surroundings of infrastructures and human settlements. In the framework of this study there is an excellent opportunity to gain new insights in the fundamental processes and mechanisms of slowly moving deep-seated rock slides from a case study in the surrounding of a large dam reservoir in Austria. New fundamentals for comprehensive slope stability analyses and hazard assessments and sound prognoses focussing on the long-term stability and deformation behaviour of slopes under changing boundary conditions (e.g. impounding of a reservoir) and/or concepts for mitigation measures can be obtained. Within this contribution, geological field surveys, deformation monitoring, geophysical and drilling data were analysed and presented. Based on the compiled and analysed data, some key-properties of the rock slide will be presented, whereby special attention will be given on the geometry and internal structure, the slope kinematics, as well as hydrogeological and geomechanical aspects.INTRODUCTIONIn high mountainous regions, deep-seated rock slides are often encountered in highly foliated metamorphic rocks such as paragneisses, micaschists and phyllites (Agliardi et al. 2012). Critical situations may occur when deep-seated rock slides fail in a rapid manner characterised by very high sliding velocities, and/or when they develop into long run-out rock avalanches. However, many rock slides in foliated crystalline rock masses either do not move at high velocities nor do they accelerate seriously and form extremely rapid slides. Displacement rates in the range of a few millimetres or centimetres per year are common for this type of rock slide (Bonzanigo et al. 2007, Tentschert 1998, Watson et al. 2007). Nevertheless, some case studies show an activity behaviour characterised by acceleration phases reaching velocities of even metres per day. However a slope collapse is not expected and these slopes decelerate to much lower base activities. The trigger for these phases can be manifold and include heavy rainfall and snow melt, initial reservoir impounding and water level fluctuations, changes in the slope’s equilibrium state due to antecedent slow deformation processes, ongoing erosion processes along the toe of the slope, and others (Zangerl et al. 2010)."

Jan 1, 2015

By M. Xiao Bo

In recent years, there has been a heightened interest in the hydrometallurgical processing of sulfide ores and concentrates (especially copper sulfide ores and concentrates) mostly in the USA and Chile. Currently, hydrometallurgical operations account for about 30% of the primary copper production. In the present research, the leaching phenomena of IOCG (iron-oxide hosted copper-gold) ores and concentrates were studied. The IOCG ore, which is characterized as having a predominant amount of magnetite with fine chalcopyrite, is currently the center of attention for new copper resources. Heap leaching of IOCG ore is desirable because of its low cost. However, the leaching characteristics of the ores and concentrates and the mechanisms of copper leaching require investigation. This study defines the factors, which affect the leaching operation, such as the ORP, pH and oxidizing agents. Based on these results, the optimal leaching conditions are provided for pilot column leaching test and ultimately, commercial operations.

Jan 1, 2007

By Robert P. Harrison, Marie-Christine Patoinel, Kristian E. Waters

This paper describes a collaboration between McGill University and Hatch Ltd. to expose undergraduate students to real-world industrial projects. As part of the final-year design course, the students receive a detailed lecture on Scale-Up of New Technologies', including seven case studies drawn from over fifty years of full-scale industrial projects. The students are taught the basic concepts of scale-up, including the limits of pure theory and the need for empiricism. Insights from real scale-up failures and successes are fictionalized as Projects A, B, C, etc. The students are then asked to identify the guiding principles that can be distilled from these case studies.

Jan 1, 2011

By Marke Wong

? Vietnam?s economy is growing so fast that gross domestic product (GDP) growth remained above 8% in 2005 and exports are rising steadily at 25% per year. ? Demand for electricity is expected to increase 18% per year through 2010 requiring an additional estimated 7,547 MW before 2010 ? Domestic coal demand is expected to be over 45 Mt by 2010. ? The Quang Ninhcoal deposits are estimated at 6.5-7 billion tons (350m) Vietnam News Agency. Saturday, May, 6, 2006. ? National resources are now estimated at 10 billion tonnes; not including a relative new coal bed discovery estimated at 210 billion tonnesin the Red River Basin.

May 1, 2006

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By Chris Yellowega

The construction and startup of a new mine is a daunting task. To successfully locate, design, build and startup an immense human endeavour like a new mine, takes perseverance, planning, dedication and significant capital. The application of capital requires a thorough evaluation of risk and where that risk is most properly limited to create the risk/return profile. One area of significant capital and thus, significant risk is the selection and maintenance of the very machinery needed to deliver the creation of investor wealth. Albian Sands Energy is the operator of the new Muskeg River Mine located north of Fort McMurray in Alberta?s oilsands. The Muskeg River Mine is owned by a joint venture of three companies: Shell Canada, Chevron Canada Ltd.and Western Oil Sands. The mine is designed to run 400,000 tons per day, 365 days per year. The mine conditions vary from material as hard and of similar consistency to pavement to underfoot conditions as soft as saturated sands. Water cannot be drained below surface conditions, shovel teeth can disappear in less than 24 hours and the primary business is often constructing large civil structures that have little to do with the delivery of ore. The mine starts with the deposit (if it doesn?t exist, nothing else matters), moves into the design, the feasibility study and the approval. The evaluation of risk and the strategies surrounding the control of that risk truly lie after these stages are complete. The strategy and execution stage is where risk is eliminated or accommodated. The point at which the investors money is being spent is the point at which the decisions made cannot be reversed. It is of absolute importance that the execution of the decisions are consistent with the strategy agreed to, lest the investors need to be asked for more money. The key sources of risk identified for the Muskeg River Mine were recruitment of trained and experienced personnel and the delivery of ore to maximize early (<2yr) cash flow. The Muskeg River Mine personnel determined that to minimize risk, personnel would be recruited to operate the mine equipment yet, the requirements for maintaining the equipment would best be held by the manufacturer. The strategy was to obtain the correct equipment for the operation of the mine and leverage the supplier?s expertise to ensure the mine wasn?t training a maintenance organization at the same time as a mining organization. In essence the key strategy for the mine start up and early operation was to leverage the equipment suppliers to maintain and repair the equipment. Albian Sands would maximize the utilization of Maintain And Repair Contract?s.

May 1, 2003

By John E. Udd

I N Part I of this paper, Professor Morrison suggested that our technique of causing cracks to develop around openings in a sheet of photoe1ashc plastic is, in effect, a laboratory-scale rockburst. Our investigations have indicated that the location and direction of these cracks are predictable, and that their growth can be controlled. On several occasions, we have been able to cause these cracks to propagate sufficiently slowly to be followed, with the naked eye. In practice, the rate of growth, gradual or sudden, would depend upon rock properties. This part of the paper presents an analysis of the stresses surrounding the openings before and after failure and also this author&apos;s views on the causes and after-effects of cracking. An attempt is made to correlate the stress patterns with those deter-mined from pure mathematics. Considering that the openings, except for the central enlargement, are long apertures with somewhat rounded corners, they might be compared with elongated ellipses having axes ratios of about 20:1 or with

Jan 1, 1963

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013