Search Documents

By Dong-Hyeun Koh, Yun-Soo Lee, Min-Seok Kim, Hyoung-Wook Kim

High strength AA7068 (Al - 7.88 wt.% Zn - 2.68 wt.% Mg - 2.07 wt.% Cu) aluminum alloy strip was successfully fabricated by horizontal-type twin roll casting. A simulation technique was used to obtain the range of casting conditions for fabricating strip without defects. The cast strip with thickness of about 5 mm was hot rolled, intermediate annealed, cold rolled to final thickness and subsequently annealed at various temperatures. Tensile properties of annealed and the aged specimens were evaluated at ambient temperature. Tensile strength and elongation of the annealed sheet are about 365 MPa and 28%, respectively. Also, the tensile and yield strength after the aging at paint baking condition (180 °C x 0.5 h) are 586 MPa and 551 MPa, respectively. Therefore, it is expected to show good formability prior to press or stamping and also provide high dent resistance after paint baking treatment.

Jan 1, 2015

The Nak?azdli First Nation and the municipality of Fort St. James are located in the Stuart Lake/Nak?al Bun area and are not unfamiliar to mining. These northern British Columbian communities have been associated with the historic Pinchi Lake Mercury mine and today are closely linked with British Columbia?s newest mine, the Mt. Milligan mine. Prior to the construction of Mt. Milligan, community health and social service providers were concerned about potential impacts that would occur from new mineral development activities. This concern has led to a partnership between the above communities and researchers with expertise in the area of mining and health. This paper describes: the current mining and health environment with a focus on British Columbia; mining trends in the Stuart Lake/Nak?al Bun area; the current community-based health research project funded by the Vancouver Foundation and the Canadian Institutes of Health Research, and; a suite of community-based health recommendations to mining companies on key issues to consider when developing projects near municipalities and Aboriginal communities in Canada, based upon one of the newest mines under development in Canada.

Aug 1, 2013

By J. Pontt

Gearless mill drives (GMD) offer high performance for torque and speed control for grinding mills and have been applied successfully in modern concentrators for wet grinding with mill diameters from 34 to 40-feet. It is considered a mature technology. However, recently, some large GMD?s have presented unexpected failures in stator and rotor subsystems. The phenomena involved in such failures has shown a complex nature and surprised users and manufacturers. The manifestation of such failures has been observed as mechanical damages to certain components of ring motors. This paper presents a discussion on the electromagnetic forces that can generate stresses in the electrical ring motor that can produce failures and outages. Guidelines for further research and contributions to improved reliability of GMD?s are proposed.

Jan 1, 2012

By S. E. Kesler, C. M. Moore, J. C. Van Loon

The possibility that chlorine and fluorine form complexes with ore metals, thereby having a strong effect on the mobility of these ore metals during late magmatic and hydrothermal processes, suggests that the abundance of chlorine and fluorine in igneous rocks could be used to distinguish intrusions that have generated ore deposits. The simplest and most economical measure of this chlorine and fluorine is the water-leachable chloride and fluoride that is released from fluid inclusions in the rock during crushing of the sample. In order to evaluate the possible use of this technique, measurements of water-leachable chloride and fluoride were made with selective ion electrodes on samples from nine intrusive complexes. There does not appear to be any simple relation between the abundance of chloride and the presence of mineralization. Fluoride values in mineralized intrusions appear to be higher than those in barren intrusions.

Jan 1, 1973

By R. J. Enkin

Modern mineral exploration depends on multidisciplinary 3-dimensional integration of geological and geophysical data. Identification of the geological sources of geophysical anomalies requires knowledge of the physical properties fingerprint of rock types, formations and their alteration products. Understanding how and why rock physical properties vary within the Earth's subsurface ensures that appropriate geophysical exploration methods can be chosen, and allows for more efficient and effective surveys to be designed. Physical properties knowledge is integral to geophysical modeling - measured data or values estimated based on geological understanding are used to produce realistic forward calculations and to constrain inversion models. Mira Geoscience and the Geological Survey of Canada, in collaboration with industry and academia, are building a Rock Properties Database System (rpds.mirageoscience.com). It compiles the most valuable physical properties for mineral exploration (density, porosity, magnetic susceptibility and remanence, electrical resistivity and chargeability) linked with location and lithological metadata. A critical knowledge gap, addressed in this study, concerns the dependence of physical properties on alteration and mineralization processes. We report on the results of a collaborative University of British Columbia - Geoscience British Columbia project, ?Integrated Geological & Geophysical Porphyry Models: Adding Value to Geoscience BC Geophysical Data?. As part of the QUEST and QUEST-West geophysical initiatives, Geoscience BC focused detailed geophysical surveys on a suite of six known porphyry deposits: Mount Milligan, Endako, Huckleberry, Bell, Granisle, and Morrison. Physical properties for a set of 269 samples of characteristic host rocks and their altered equivalents were measured. The causes of physical properties variations were investigated through their correlations with ore and alteration mineralogy determined from thin-section observations and X-ray diffraction analyses. Physical properties of variably altered host-rocks and intrusive rocks vary significantly between different BC porphyry deposits. No specific unifying geophysical model exists that can be uniformly applied during exploration. Knowledge of local background geology and local physical properties variations is necessary as host-rocks and intrusive rock compositions vary depending on magmatic affinities, and alteration styles will vary reflecting host-rock compositions, crustal depth and influence of meteoric water. A district-scale exploration strategy requires location of intrusive bodies, which are commonly magnetic, resistive and low in density. Correlations should not be expected between density and magnetic susceptibility, because alteration may lead to magnetite destruction or to secondary magnetite development. Deposit-scale ground geophysics might image potassic alteration zones that can be magnetic in both alkalic and calcalkalic systems. Low magnetic susceptibilities, resistivities and densities might aid in locating the typically more porous phyllic and argillic zones. All geophysical data must be interpreted with background knowledge of local rock types and in light of the expected deposit model and associated magmatic and hydrothermal processes. The most effective means to building physical properties knowledge prior to geophysical investigation remains collecting rock physical properties measurements. The cost of rock properties data collection is low, relative to the overall costs of running a mineral exploration program, and can provide an important framework for design of geophysical surveys, survey method selection, geophysical modelling, and data interpretation.

Aug 1, 2013

By Eliodor Stoian

PRESSURE information has earned a place of recognition to almost everyone interested in oil and gas production. This interest is due chiefly to the multitude of uses to which it can be put. A sub-surface pressure test, conducted for as little as $60, may yield data worth many times its cost. To the uninformed, the testing techniques may seem complex. Fundamentally, however, they consist merely of the application of common sense. At one time, sub-surface pressure data were used only in identifying individual well problems and in finding appropriate solutions. Today, it is generally acknowledged that sub-surface pres-sure .data are essential for the proper evaluation and exploitation of oil and gas pools. The following is a review of significant applications of sub-surface data with regard to: (A).-Development (B) .-Completion and work-overs (C) .-Production (D) .-Reservoir engineering (E).-Proration (F) .Other applications of pressure data of a more general nature.

Jan 1, 1958

By R. W. Boyle

"The concept of using chemical methods in prospecting dates back at least to the middle of the 16th century. Modern methods of geochemical prospecting, however, based on secondary haloes and utilizing trace-element techniques, were first practised in the U.S.S.R. and the Scandinavian countries in the 1930's. After 1945, methods based on soils, stream sediments and vegetation were rapidly developed in the U.S.A., the United Kingdom, Canada, France and other countries.The modern methods of geochemical prospecting owe their rapid development in the 20th century to the following:1.-Recognition of the primary and secondary dispersion haloes and trains that are associated with all mineral deposits. 2.-Development of accurate and rapid analytical methods utilizing the spectrograph and the various specific sensitive colorimetrie reagents, especially dithizone. 3.-Development of polyethylene laboratory ware of all types and the development of resins. This permitted greater freedom of field analyses and reduced the incidence of contamination.4.-Development of gas chromatography. This permitted the rapid and accurate determination of hydrocarbons in petroleum prospecting.Future research in geochemical prospecting should be focused on the following tasks: 1.-Definition of geochemical provinces and their relation to mineral deposits. 2.-Development of methods for discovering large low-grade deposits. 3.-Development of methods for discovering deeply buried deposits. 4.-Further development of methods to outline primary haloes. 5.-Eiucidation and formulation of techniques to relate the size and intensity of anomalies to the grade of the deposits. 6.-Development and refinement of biogeochemical methods, especially those based on indicator plants, chlorotic or toxic effects, and microbiological techniques. 7.-Definition of the types of primary and secondary haloes associated with accumulations of oil and gas."

Jan 1, 1967

By J. D. T. Steyl

"This paper presents a phenomenological model of the rate of iron(III) precipitation in batch and continuous autoclaves at medium temperature operating conditions. The rate expressions are based on information obtained from the literature and experimentation at low and high pulp densities. Special allowance is made for the formation of surface nuclei, which appears to be promoted at a higher iron(III) precipitate surface area, especially in suspensions of lower terminal acidity. This leads to the formation of secondary particulates and provides the required link to simulate high pulp density leaching-precipitation systems, using low pulp density batch precipitation data. In particular, the model allows direct application of the simulation to the autoclave oxidation of iron-containing copper sulfide concentrates and provides a good estimation of the relative precipitation rate of hematite, the preferred product, compared to hydronium jarosite. Some interesting mechanistic understandings of iron(III) precipitation in autoclaves are further elucidated.INTRODUCTIONThe objective of this work is to describe the rate of iron(III) precipitation and the relative amounts of hematite compared to hydronium jarosite precipitation during batch and continuous chalcopyrite oxidation under medium temperature (MT) (~130 to 160ºC) autoclave conditions. Published information has not yet revealed sufficient mechanistic insights about this sparingly soluble salt system under these conditions. The rate expressions in this paper are based in part on current literature information, supplemented by qualitative experimental observation at low pulp density conditions, in particular the high-resolution backscatter electron (BSE) images and particle size distributions (PSDs) of the precipitates. A summary of this work and insights from the literature are presented first, after which the behaviour of iron(III) in high pulp density leaching systems is used to derive a phenomenological expression of the effect of existing iron(III) precipitate surface area on the precipitation rate. The overall regression encapsulates all the experimental results, i.e., those obtained in both batch and continuous autoclave configurations (Steyl, 2012a)."

Jan 1, 2012

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953

By C. J. Hodgson

"IntroductionThe Kitsault molybdenum mine is located 600 m above sea level on Lime Creek at the head of the inlet of Alice Arm, 140 km northeast of Prince Rupert, British Columbia (Fig. 1). The area of the mine is characterized by rugged topography and deeply incised creeks which drain into the Portland Canal - Observatory Inlet fjord system. Access is by air service or boat from Prince Rupert, or by secondary road from Terrace.HistoryThe deposit was first staked in 1911, at which time the main feature of interest was a polymetallic vein with values in silver located southeast of the molybdenum deposit (Woodcock and Carter, 1976). Turnbull (1916) was the first to describe the extensive zone of crisscross quartz stringers with Mo~ on the banks of Lime Creek which, although it clearly had the potential to contain a major deposit, was not then believed to be of commercial value.Following sporadic work through the 1920s and early 1930s, the ground lay idle unti11959 when Kennco Explorations (Western) Ltd. commenced a program of systematic diamond drilling on the stockwork-type mineralization adjacent to Lime Creek. In late 1964, Kennco announced the presence of an orebody of 36 million tonnes averaging 0.230Jo Mo~ which was to be put into production at a rate of 5450 tonnes per day under a new subsidiary, British Columbia Molybdenum Ltd., at a forecasted capital cost of $20 million (revised to $30 million).Between January 1968 and April 1972, 10.4 million kg of molybdenum were produced from 9.3 million tonnes of ore, at an average mill recovery of 90%, and with an average mill head grade of 0.206% Mo~. The ore was mined in an open pit with a waste to ore stip ratio of 1.5 to 1. The. operation was terminated in 1972 due to weak molybdenum prices and escalating costs.In May 1973, the deposit was purchased by Climax Molybdenum Corporation of British Columbia, Limited and in 1979 transferred to affiliate Amax of Canada Limited. In early 1979, following completion of detailed feasibility studies, Arnax commenced construction of the 10 900 tonne per day Kitsault mine and mill complex based on a mineable open pit reserve of 95 million tonnes at an average grade of 0.192% Mo~, sufficient for a mine life of 25 years. The original capital cost estimate was $143 million; it subsequently escalated to approximately $200 million."

Jan 1, 1995

By P. Lausch, Z. X. He, J. F. Archibald

"Documented underground fill failures have resulted because of the lack of adequate knowledge concerning fill strength and other physical parameters, as well as to a lack of consistent quality of fill materials being used by operators. On the basis of literature review and correspondence with backfill operators at 18 mines throughout the province of Ontario, non-systematic quality control procedures have been shown to exist, both within different levels of single operations and between separate mining operations, which act to provide inferior engineered fill materials and erratic application response in situ.Assessment of existing procedures set by mine operators for determining backfill physical parameters, and recommendation of optimum fill material testing and manufacturing guidelines are presented in this paper.A series of standard fill characterization test procedures are recommended to provide substantial, though not comprehensive, fill behaviour review. The purpose of these recommendations is to propose industry standards for backfill quality review. Data acquired could be utilized for fill design functions and as a means of comparing fill quality parameters between sites in a regular and more systematic fashion than is presently done."

Jan 1, 1993

By H. Nouranian, M. Askari

GOLGOHAR Mining & Industrial Co., with annual production of 16 million tons, is one of the largest pelletizing and iron ore supplier in Iran that recently this year, because of using mineral processing techniques and extraction of ore body positioning between the metamorphic rocks, about 150 million tons of dry tailings has been created as a result of concentrate production. On the other hand, many environmental issues such as groundwater pollution have been developed by sulfide and silicate gangue minerals, which containing heavy metals such as mercury and arsenic. In this study, a new product with high added value has been introduced for the company by identification and extraction of industrial minerals in dry tailings. Also, by removing large masses of dry tailings, environmental pollution sources were gradually eliminated. This method can be used as a modern waste management approach in the world.

Jan 1, 2017

By E. De Souza

The instrumentation and monitoring of rock behaviour have played an important and necessary role in the practice of potash, rocksalt, gypsum, trona and coal mining. The art of rock instrumentation applied to soft rock and coal mining has progressively evolved over the past years and will surely continue to advance at a faster pace in the future as a result of the technological revolution we experience today. The development of sophisticated mine-wide data communications systems is being used for instrumentation and sensor automation, and laser, sonar and geophysics technology are being continuously adapted for rock monitoring purposes. In this paper, the author provides an overview of typical rock instrumentation used today and offers some views of the progressive evolution in rock mechanics instrumentation sophistication and design.

Jan 1, 1998

By Staff

The Tetreault mine, operated by the British Metal Corporation (Canada), Limited, holds a unique position in Canadian mining, being the only steady producer of zinc in Canada east of the Rocky mountains. Its importance in Canadian zinc production may be gauged with some accuracy, since, in 1927, it was responsible for over 13 per cent of the zinc output of the Dominion. In addition, it also made valuable contributions to the production of lead, silver, and gold. Location: Situated in the foothills of the Laurentian mountains, 600 feet above sea level, 20 miles from the St. Lawrence river, and 52 miles due west from the city of Quebec, the property is in the township of Montauban, county Portneuf, Province of Quebec, as shown in Figure I. The municipality of Montauban, immediately adjoining the mine, has a permanent population of 700 people and is six miles by road from Notre Dame station on the main line of the C.N. Rys. between Montreal and Chicoutimi-Notre Dame being n6 miles by rail from Montreal. Connection by 19 miles of dirt-and-gravel road with the Provincial highways' system of Quebec Province, the city of Quebec, which is distant 78 miles, can be reached by automobile in less than three hours, while the distance to Montreal by road is 16o miles .

Jan 1, 1928

By Marc R. Laflèche, Suzanne Paradis, A. Shirley Péloquin, Harold L. Glbson, Robin Potvin, Pierre Verpaelst

"The Archean Blake River Group is best known from a central volcanic complex in Rouyn-Noranda. This volcano-tectonic depression, delimited by the Hunter Creek fault to the north and the Horne Creek fault to the south, is interpreted to be a cauldron approximately 20 km in diameter. Its western and eastern boundaries are the Flavrian Plutonand the D'Alembert shear zone respectively. The complex has an exposed stratigraphic thickness of 10.5 km. Two cycles, composed of andesitic units overlain by bimodal, andesite - rhyolite units, are observed in the area, and are, in turn, overlain by an andesitic unit interpreted to be the lower part of a third cycle.The southern sector of the Blake River Group, south of the central volcanic complex, is considered to be outside the limits of the cauldron, but partly contemporaneous with it. The maximum stratigraphic thickness exposed in this area is 4 .6 km. At least two cycles occur in this sector. The oldest unit, a pre-cauldron andesitic to basaltic unit, occurs only in the southern part of the sector. In the north, two partial andesite - bimodal cycles, interpreted as contemporaneous with the cauldron volcanism, are observed.The eastern sector of the Blake River Group, east of the central volcanic complex, apparently overlies the complex. Two units are observed in this sector: a lower bimodal unit and an uper andesitic unit. The bimodal unit is coupled with the uppermost andesitic unit of the central volcanic complex to form a cycle, and the andesitic unit is considered to be the uppermost unit of the Blake River Group. The total exposed stratigraphic thickness in the sector is 2.5 km.The western sector of the Blake River Group, north and west of the central volcanic complex, is interpreted as the lateral equivalent of the complex. Three andesite - bimodal cycles are exposed in this sector, giving a total stratigraphic thickness of9 .5 km. The two lower cycles correspond directly to the central volcanic complex cycles; this correlation is facilitated by two stratigraphic marker units observed on either side of the Hunter Creek fault: the Fish-roe rhyolite flow, east of the Flavrian pluton, and a spherulitic rhyolite lapilli-tuff, west of the Flavrian pluton.Many of the volcanogenic massive sulphide deposits found in the central volcanic complex are spatially and temporally associated with synvolcanic faults, and felsic domes and feeder dykes that are the sites of felsic volcanism in the bimodal units. However, these features also occur outside the central volcanic complex, and the similarities recognized in this work between the complex and the surrounding area suggest that such deposits need not be restricted to the central volcanic complex. The presence of volcanogenic massive sulphide deposits outside the complex confirms this."

Jan 1, 1990

By George E. Cole

"It is a truism that the metals, and particularly the precious metals tend to monopolize the attention of those interested £n the mineral industry. This is a tendency to be mildly, but actively and continuously combatted if we are to have a well-rounded mineral development." There are in the province of Ontario a number of industries centred about the non-metallic minerals. Too little is heard of the part these play in our industrial life. It is with the intention of showing what the gypsum industry is doing in Ontario that this paper is written. The writer lays no claim to any originality in the discussion and merely offers some material in an endeavour to assist in bringing about that 'well-rounded mineral development' sought for Ontario. M. Y. Williams in his "The Silurian Geology and Faunas of Ontario Peninsula and Manitoulin and Adjacent Islands"1 in discussing the industries dependent on the Silurian rocks of south-western Ontario points out that "the splendidly ordered gypsum mine at Caledonia, formerly owned by the Alabastine Company of Paris, and now owned by the Ontario Gypsum Company, is a revelation to the average man, who disconnects mining entirely with this part of Ontario". This region is better known as one of the richest and most thickly settled agricultural areas in Canada.

Jan 1, 1925

By F. A. Forward

"NINETEEN sixty-six is a year of unusual significance in our Institute and in our country. It marks two-thirds of a century of service by the Institute to the people of the mineral industry and two-thirds of the century that Sir Wilfred Laurier said ""belongs to Canada."" As we meet here today within the historic walls of Canada's oldest city, a city that looks back on three hundred and fifty years of progress, I am reminded that it is almost a third of a century ago -in April, 1934 -that here in Quebec I first attended an Annual General Meeting of the Institute. It occurred to me that it might be appropriate to examine briefly the change that the middle third of this century has brought in the affairs of the mineral industry and, with some trepidation, to consider the prospect for the third that lies ahead.Opinions differ as to the relative importance of factors that have been responsible for the expansion and growth of Canada in its first hundred years. Some will say that it has been due to the abundance and fertility of agricultural land, others to the early enterprise of the railroads, and financiers believe that the banking system has been a major factor; -the fisherman -the forester -the teacher -each has his own view. I suspect, however, that most of us here would subscribe to the thesis of T. A. Rickard -miner, author, imperialist -who wrote, a gene-ration ago, ""Trade follows the flag, but the flag follows the pick,"" and thus agree that the finest contribution to progress, to wealth, to extension of frontiers and to inter-national trade has been provided by the mineral industry."

Jan 1, 1966

By S. Homulos

"Introductory and GeneralTHE Northwest Territories comprise all that region -of Canada lying between Yukon Territory and Hudson bay and north of the 60th parallel of latitude. For purposes of mine .administration the Territories are divided into three districts: Yellowknife, McKenzie, and Arctic and Hudson Bay. Mining recording offices for the respective districts are maintained at Yellowknife, Fort Smith, and Ottawa. The mine inspection for the entire area, and also for Yukon Territory, comes under the Federal Department of Resources and Development. Two mining inspectors are responsible for these inspections: the Chief Inspector of Mines, with headquarters in Ottawa, who makes trips into the north at least twice a year, and a Resident Inspector, stationed in Yellowknife.The Resident Inspector is constantly making inspections of active properties. This involves a considerable amount of air travel as the region is large and properties are widely scattered.Although there has been prospecting and staking of claims in each of the three districts of the Northwest Territories, actual mining has been conducted only in the Yellowknife district, and for purposes of this paper we are solely concerned with that district."

Jan 1, 1952

By J. Lee

A monolithic caisson is one of the major structural components commonly used in the construction of docks, breakwaters, and container terminal quay walls. Since the structure of monolithic caissons is typical and somewhat simple, its design process is also typical and repetitive, but still time consuming. To reduce the total time and enhance productivity, we developed a parametric model in Revit to automatically generate a 3D model of a monolithic caisson. It is designed to generate the Revit model of a caisson with concrete body and reinforcing bars. The size of caisson, the number of reinforcing bars, and the space between reinforcing bars are automatically changed when users update parameters. This paper presents how we developed this parametric family in Revit for monolithic caisson design and how it would enhance its design process.

Aug 1, 2013

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019