Search Documents

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

"The Society for Mining, Metallurgy, and Exploration (SME) Inc. developed a guide of minimum standards for reporting exploration results, mineral resources, and mineral reserves for the purpose of informing the general public. The SME Guide has been adopted by the Society.History1. In 1988, at the request of members of the Society for Mining, Metallurgy, and Exploration (SME), Inc., the President of SME formed Working Party #79, Ore Reserve Definition, with the mission to develop guidelines for the public reporting of exploration results, resources, and reserves. A Subcommittee was appointed by the Working Party to draft these guidelines and submit recommendations to SME. The Subcommittee's recommendations were published by SME in the April 1991 issue of ""Mining Engineering"", and as a document entitled ""A Guide for Reporting Exploration Information, Resources, and Reserves"" (the SME Guide) in January 1992. Work continued on an ad-hoc basis until 1996, when Working Party #79 was renamed the SME Resources and Reserves Committee and became a standing committee.In 1994, the Council of Mining and Metallurgical Institutions (CMMI) started a concerted international effort to create a set of international definitions for reporting mineral resources and mineral reserves. An ad-hoc International Definitions Group was formed, with representatives from mining and metallurgical institutions from the United States (SME), Australia (AusIMM), Canada (CIM), the United Kingdom (IMM) and South Africa (SAIMM). A major breakthrough came on October 18, 1997 when the CMMI International Definitions Group met in Denver, Colorado and reached a provisional agreement (the Denver Accord) on definitions of mineral resources and mineral reserves. Concurrently, and since 1992, the United Nations Economic Commission for Europe (UN-ECE) was developing an international framework classification for mineral resources and mineral reserves. Starting in October 1998, joint meetings were held in Geneva between the CMMI International Definitions Group and the UN-ECE Task Force, resulting in agreement to incorporate the CMMI definitions into the UN framework classification."

Jan 1, 2003

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By F. Romero

In the last four years, Compañia Minera Doña Ines de Collahuasi has been working in the application of advanced multivariate statistical techniques for the improvement of the metallurgical processes. In this paper the main conclusions for the application of multivariable analysis to the EW process are presented; including the identification of (target) process patterns according to throughput and quality criteria. Based on the process patterns, process variables hierarchies were identified by selecting the most influential ones, as well as to identify and isolate the root causes of pattern deviations and sub-standard operating conditions, cause-effect relationships were established, leading to the definition of process policies and controls to give early corrections to potential failures. The analysis was focused on cathode quality, specifically in its sulfur content, using an empirical model based on those variables that from a phenomenological and statistical stand point appeared to be the most influencing ones.

Jan 1, 2007

By M. V. Rowley, D. D. Warkentin

With high commodity prices, tightening operating budgets and increasing disposal costs, there is an increasing interest in processing municipal waste streams, such as the ash derived from combustion processes. This paper describes laboratory development work for a process to recover metal values from the finer fractions of these wastes. The work was initially aimed at recovery of copper and the removal of lead and other heavy metals from the ash residue, but results showed gold and silver recovery to be an important objective as well. The process uses gravity and flotation as the principal separation steps, with gold recovery occurring mainly in the flotation stage. The particle size range and chemistry of the ash presented numerous challenges to developing a suitable flotation method, but an effective flowsheet was developed by separating the ash into a fine fraction and a separate slime fraction, each with a unique flotation strategy. Specialized conditioning stages and careful reagent selection have resulted in effective gold and silver recovery from a range of ash types and sources. The work has resulted in a patent being issued for a process based on this novel approach to the treatment of combustion wastes.

Jan 1, 2017

"This document sets out the Exchange’s expectations and requirements for a valuation of mineral properties and outlines: the general purpose of valuation reports; guidelines respecting circumstances where the Exchange will require a valuation report; and valuation standards, guidelines and methods that are generally acceptable to the Exchange, 1. IntroductionThis Appendix sets out the Exchange's expectations and requirements for a valuation of mineral properties and outlines:(a) the general purpose of valuation reports;(b) guidelines respecting circumstances where the Exchange will require a valuation report; and(c) valuation standards, guidelines and methods that are generally acceptable to the Exchange.Mining industry standards and guidelines for valuations and valuation reports can be found in the Canadian Institute of Mining, Metallurgy and Petroleum Standards and Guidelines for Valuation of Mineral Properties (""CIMVal"") published in February, 2003 (www.cim.org). CIMVal consists of two parts, Standards and Guidelines. The Standards are mandatory and must be followed in order for a valuation to be CIMVal compliant. The Guidelines in CIMVal are not mandatory, but are strongly recommended.The Exchange requires that CIMVal Standards be used by Issuers and their professional advisors when preparing valuations and valuation reports on mineral properties. The CIMVal Guidelines should be followed by Issuers and their professional advisors in preparing valuation reports on mineral properties, with the exception that the valuation methods and guidelines under Section 4 Acceptable Valuation Methods and Guidelines below, must be followed."

Jan 1, 2003

By Eric D. Marks

Fatalities resulting from ground workers colliding with objects and construction equipment accounted for approximately 18% of the total construction fatalities experienced in 2010. Current injury and fatality measuring methods have proven to be inadequate due to their use of passive measures of safety rather than a more active approach, such as the use of leading indicator data (also called near misses) of hazardous proximity situations between ground workers and heavy equipment on construction sites. The objectives are to create and evaluate the effectiveness of a reliable algorithm for collecting and analyzing the resulting leading indicator data from hazardous proximity situations. Numerous experiments emulating typical interactions between workers-on-foot and heavy equipment are used to evaluate the proximity sensing and detection technology. Safety leading indicator data (also called near misses) generated by the proximity sensing and detection technology during the experimental trials are used to create and assess the resulting algorithm. Results from the experiments indicate that leading indicator data generated from these systems can be processed and analyzed to identify hazardous proximity situations and incidents on construction sites.

Aug 1, 2013

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By Jeff Bird, Xijia Wu, Prakash C. Patnaik

"Prognosis and health management (PHM) is an evolving suite of technologies intended for application to the life cycle management (LCM) of mission/safety critical systems, with anticipated results, which will: - Reduce life cycle cost - Enhance operational safety and readiness - Assist in maintenance decision-making - Enable autonomic logistics While it is emphasized in the United States that future multi-mission fighter aircraft such as Joint Strike Fighter (JSF) must have PHM capabilities, Canadian initiatives also recognize the need to implement such schemes for future and legacy military and civil aerospace systems. With respect to four major technology areas of PHM, i.e., i) advanced sensors, ii) data analysis and fusion, iii) life consumption evaluation, and iv) predictions with reliability/risk assessment, there has been advanced technologies developed by NRC and others within Canada: - Aircraft/engine instrumentation and airborne data recording systems - Signal analysis and data fusion - On-line engine health monitoring - Physics based models for engine material failure modes and life prediction - Autonomic crack growth analysis for damage tolerance of engine components - Mission severity analysis algorithm - Probability, reliability and risk assessment This presentation reviews the above technologies in relevance to PHM, emphasizes the need to have physics based models and outlines the future R&D needs for integration and implementation of these technologies suitable for the advanced and legacy aircraft."

Jan 1, 2004

By B. Lewis

Paper did not make deadline for printing

Jan 1, 1982

"During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests.In the current case, a composite sample of gold ore is dedicated to a Gravity Recoverable Gold (GRG) test. The properties of interest are the head grade of gold, the size distribution of the material, and the gold assay per size class. The sample is mixed and a sub-sample is taken to measure the feed properties: the size distribution and the gold assay per size class. The remaining material of the sample is subject to the first stage of concentration using the laboratory Knelson concentrator. The concentrate is analysed in its entirety, while a sample of tailings is taken for the same analysis. The remaining part of tailings is subject to grinding to feed the second and third stages of concentration. Similar sampling is performed at each stage.The concentration performances are analysed in light of these measurements. But what is the accuracy of the measurements of the properties? Pierre Gy’s theory of sampling, associated with a heterogeneity model built using the GRG test results, will answer this question. The current paper presents, through a real example, the calculation of the errors of the measurements of size distributions and gold assays performed during the GRG test. The uncertainties of the concentration performances and liberation size estimate are then calculated and their impact on the results interpretation is analysed.INTRODUCTIONDuring the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material from a selection of various drilling products or a sample from a mining test. It can be also a sample from an existing plant in order to investigate process enhancement. This sample can represent several tonnes of material which are analysed and split for use in various tests. In order to take into account the ore variability in terms of gold deportment, it is recommended to perform variability studies (Dominy, Murphy, & Gray, 2011, Dominy, 2013) using samples representing various horizons or years of production. But for a given ore type, it can be necessary to perform many tests with different operating conditions (Brochot, 2012a). In that case, the variability of the samples is not due to the heterogeneity of distribution of the deposit, but only on the heterogeneity of constitution of the primary sample. The level of confidence associated with the estimated performance parameters is directly linked to the overall error (including sampling error) of the measurements performed during the tests."

Jan 1, 2016

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

By Yasuo Iizuka

We have had studied CO oxidation on unsupported Au powder (mean particle size, ca.100nm) manufactured by evaporating ultra high purity gold metal (>99.99%) in inert gas and reported that it showed some activity after oxidizing pretreatment in O2 at 423 K?453 K. However, recent XPS analysis of the Au powder revealed that it contains much amount of impurity metals such as Ag and In at levels which far exceed those expected from the impurity level of raw gold metal in the bulk. Several samples of Au powder containing different amount of impurity metals were prepared to examine whether the activity depends upon the existence of surface impurity or not. Activity measurements were performed at 273 K after undergoing the powder under various pretreatment conditions. Although the activity of Au powder varied to some extent according to the pretreatment condition, it is strongly correlated to the surface concentration of Ag. Such dependence was not found for In, indicating that the activity of unsupported Au powder is mainly due to the existence of Ag in the surface layer. The activity attributable to ?particle size effect? was not recognized for Au powder with a mean particle size larger than 80 nm.

Oct 1, 2003

Arguably the SMC Test® has become the most popular laboratory hardness test in the world with over 17,000 tests having been completed to date, covering over 650 different ore bodies. It is now routinely used in design, optimisation and orebody profiling projects. The test is unique in that from relatively small amounts of drill core it simultaneously provides parameters that are used in simulation modelling of AG/SAG and crushing circuits as well as work indices that are used in power-based equations for predicting the specific energies of AG/SAG/Crushing and HPGR circuits. The very large data base that has been accumulated has provided the opportunity to study the differences in variability from deposit to deposit. This paper describes and discusses the trends that have become apparent from the study of this data base. Recommendations for appropriate selection of sample numbers are also made which are based on these trends.

Jan 1, 2012

By C. Cristonffanini, S. Nazari

"In the past, simulation was considered to be an offline tool disconnected from plant operation. Advancements in the computation power combined with utilizing physics and chemistry sciences have allowed us to significantly improve the modeling and simulation technology for mining and mineral processing. This paper investigates the benefits of first principle models and simulation by connecting them to real time operation. Process data are connected to high fidelity models executed in parallel to the operation. In recent literature, this concept is known as Digital Twins. The Digital Twin is used for various purposes such as optimization, virtual instrumentation and condition monitoring. Using IDEAS™ simulation software we are able to construct a digital twin for different equipment inside a mineral processing plant. Two case studies for building a digital twin for the primary hydrocyclone feed pump and thickener underflow are presented. Using the pump’s model, a digital twin is developed and is installed in a gold extraction plant that is able to infer the slurry density in real time. Additionally, it is used for detecting sanding in the pipes and impeller condition monitoring.INTRODUCTION Since the eighties, thanks to advances in computation technologies, computer based simulation of processes using first principle models has become a well-known engineering tool for various industries. As our understanding of processes has increased, their representative models have become more realistic and more sophisticated. Due to this increase of accuracy, use of simulation is becoming more fundamental in process industries. The main goals to use accurate simulation is to decrease the engineering and construction cost, optimize the process design and improve the operation performance by decreasing operation cost and increasing efficiency. The term Digital Twin was first introduced in 2010 by NASA (Shafto et al., 2012) in aerospace industry. Subsequently, the concept quickly spread through other industries. As of today, no standard organization has provided an official and unique definition of Digital Twin for process industries. However, there are three important aspects that are common throughout various descriptions. When simulation is core functionality of the process (1) along the entire life cycle of the plant (2) with direct linkage to operation (3), it is called that process has a Digital Twin. According to Gartner, the concept of Digital Twin has elected as fourth most important disruptive technology for the year 2018 (https://www.gartner.com/, 2017)."

Jan 1, 2019

By Alessandro Navarra

Discrete event simulation provides a computational framework in which the use of smelting equipment can be analyzed and optimized, leading to the development of alternative modes of operation. Much of the complexity of copper and nickel smelters is centered on the converter aisle. These converters operate in parallel, produce batches, and set the tempo for the downstream operations. In practice, smelter staff schedule daily operations to coordinate the smelting furnaces and converters with downstream operations. Thus, a realistic simulation of smelter operations, over hundreds of days, should incorporate converter scheduling algorithms as presented in this paper.

Jan 1, 2014

"Introduction The first documentary record of coal nurung on Vancouver Island was that of the Hudson Bay Company operations in the Suquash area in 1836. Between 1836 and 1862, the Hudson Bay Company mined some 65,000 tonnes from this Suquash field and the Nanaimo coal fields discovered in 1851. However, systematic mining of coal did not take place until the Hudson Bay Company holdings were sold to the Vancouver Coal Company in 1861, and a rival company under Robert Dunsmuir was established in 1869. These two interests under various organizational names and jointly as the Canadian Collieries (D) Ltd. (1928) developed and exploited the coal seams of the Nanaimo and Comox Basins from 1852 to 1966. Because of the proximity of the coal outcrops to tidewater, the coal was readily marketed to ocean-going and coastal ships for fuel. However, during the turn of the century the main market was to meet the demand of the developing cities along the west coast of Canada and the United States for residential and commercial heating. Island-based copper smelters and brick factories, and the coming of the railroads motivated by steam engines increased the demand. This economic success of the industry continued until 1922 when a peak production of over 1,750,000 tonnes was reached. Following 1922 labour unrest in the industry, which affected the certainty of supply, and the availability of alternatives in the form of California petroleum and mainland coal combined to cause a rapid and steady decline in the demand for Island coal. In spite of post-and pre-wartime prosperities the trend could not be reversed. Serious coal mining phased out in the Nanaimo area in 1939 and in the Comox area in 1967. puring the 114 years in which the industry flourished over 75 million tonnes of coal were mined from more than 30 mines and a minimum of ten new mining communities were established on Vancouver Island."

Jan 1, 1985