Search Documents

By R. Erpelding

High Pressure Grinding Rolls (HPGR) are said to be a good option in new grinding circuits. Due to their low energy consumption compared to other grinding systems such as SAG milling, there is a strong incentive to check their behaviour for certain ore types. With rising energy prices the operation will become even more beneficial in future. As published in the past, the HPGR is claimed to increase the liberation of the valuable mineral component within an ore. An investigation at the research centre of Polysius was conducted to substantiate the liberation behaviour in finish grinding operations. A pilot scale HPGR test unit (POLYCOM MAGRO) with a roll diameter of 950 mm and processing capacity of 80 t/h was used. Grinding tests were completed with a screen and a two stage drying air separation process (SEPOL). Analysis included standard screen analysis, fractional XRF and modern MLA technology. A technique was developed to oppose the amount of produced slimes (resuming bad flotation) against the positive effect of producing high mass fraction at flotation-easy sizes. The paper shows how effective the use of a dry grinding separation could be in terms of production of mass of liberated metal.

Jan 1, 2012

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By H D. Smith

T HE production of coal in Canada was slightly higher in 1964 than in the immediate past, and the major users continue to be the electric utility and metallurgical industries. There are continuing trends toward the increased use of cokes and chars in various metallurgical applications. Geological Research During 1964, the coal drilling program of the Research Council of Alberta (RCA) was concentrated in the extreme south of the Province (notably in the Milk River area and the region immediately to the northeast of this area). Field work commenced on June 1 and was completed at the end of September, by which time a total of 376 holes, aggregating some 48,500 ft., were drilled in 132 townships. Although no new major coal occurrences were intersected, the pro-gram yielded useful data for defining the extent of the known coal deposits in the area. Detailed results will be analyzed during the winter and reported in due course. Meanwhile, a full report on the

Jan 1, 1965

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991

By G. Granata, C. Tokoro, M. Matsuoka, K. Horiuchi

"Given the high demand of copper and the lack of new high-grade deposits, low grade copper ores containing copper oxides and refractory sulfides need to be processed as well. However, in order to recover copper from refractory copper ores, the leaching performances should be improved. In this study, we investigated the effect of the mechanical activation in the leaching of copper from covellite. The influence of a mechanical treatment by planetary ball milling on leaching rate in sulfuric leaching media was evaluated by using X-ray diffraction (XRD), mineral liberation analysis (MLA) and X-ray absorption fine structure (XAFS). Results showed a significant increase in copper leaching from around 50%up to 100% along with an improvement of the leaching kinetics when using planetary ball milling. XRD spectra showed the disappearance of the covellite peak from (101) face, thus suggesting the amorphization of covellite associated with the use of planetary ball milling. XAFS results showed that the coordination number of Cu changed from 6 to 3, thereby confirming the effectiveness of the mechanochemical effect.INTRODUCTIONDuring the last decades, while the copper grade in copper ores has been decreasing, the concentration of impurities such as arsenic tends to increase, thus requiring for the processing of low grade copper ores. For a suitable processing of copper minerals, hydrometallurgical processes are preferable due to the lower costs, the lower environmental impact and the easier implementation (Watling, 2006). However, for an economical recovery of copper, the leaching performances must be improved.Among the recent advancements in leaching technologies, the mechanochemical activation allows for an improvement of the leaching performances by means of high-intensity grinding(Mohammadabad et al., 2016). In the first place, the improvement is the result of the dramatic decrease of particle size, which results in an increase of the mineral surface area and the consequent enhancement of leaching kinetics. Furthermore, the intense mechanical stress due to the high-intensity grinding could induce the rupture of the crystal structure producing a decrease of crystallinity. Such changes of the mineralogical structure, also known as mechanochemical effect, can lead to more leachable mineral, thereby resulting in a greater dissolution of copper. Last but not least, whereas the mineral surface might undergo passivation during leaching, the high-intensity grinding can continuously refresh the surface of the mineral, thus exposing portions of unleached bulk mineral."

Jan 1, 2017

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By John I. Sharpe

Masses of pyritic copper and zinc ores are entrapped along the contact zone between two volcanic groups in the Matagami area. The upper limits of the sulphide concentrations tend to form concordant contacts against lava or cherty tuffite units of the younger group; the lower extremities tend to either follow transverse structures or merge with zones of dispersed sulphides. The sulphides are deformed and intruded by folded dykes. Close relations between metallization boundaries and volcanic lithology and stratigraphy, and a preliminary investigation of the fabrics and crystallization temperatures of the sulphide masses, suggest that the copper and zinc (but; not necessarily all the iron sulphides) were emplaced at h1gh temperatures during volcanism in near-surface lithological-stratigraphic traps. Introduction T HE Matagami area is centered 120 miles north of the Val d'Or and Noranda camps in north-western Quebec. For the present purpose, it is considered to comprise a 155-square-mile area in Isle-Dieu, Galinee and Daniel townships which encompasses the main sulphide masses. Airborne geophysical surveys within this area in 1956 led to the discovery of a large sulphide body -the.

Jan 1, 1965

By A. S. H. Kabir, I-H. Jung, J. Su, Yue. S., M. Sanjari

One of the major problems associated with conventional wrought magnesium alloys is the unwanted basal texture that forms during plastic deformation which generally does not change markedly after post-deformation annealing. Formation of precipitates on the recrystallized grain boundaries during annealing may affect the usual rotation of grains towards preferred basal direction resulting in texture weakening. In this study, Mg-Al-Sn alloy was hot compressed at 250°C and annealed at 350°C for various times. The initial as-deformed microstructure was partially dynamic recrystallized with dynamic precipitates on the grain boundaries. After annealing at 350°C, static recrystallization of the bimodal microstructure took place where at this temperature no static precipitates formed. The goal of this work was to study the effect of dynamic precipitation on the texture evolution during the annealing process. Texture evolution was studied during annealing by electron backscattered diffraction (EBSD) technique through a microstructure tracking process. It was found that precipitates on the recrystallized grain boundaries have significant effect on the usual rotation of the grains towards the basal direction, meaning significant texture weakening, which is beneficial for final mechanical properties.

Jan 1, 2015

By D. S. Evans

Major Project Blues Over the last two decades, almost every major project has suffered significant cost overruns, significant schedule delays, and/or poor quality work. Exceptions are rare and most projects that tout being ?On Time and Under Budget? have re-cast schedules, significantly modified scope or revised base estimates. The problem isn?t new. In the late 1980?s the Rand Corporation published a study showing that 80% of all major projects had significant cost and schedule overruns. The problem is not restricted to the Canadian environment, or to a specific industry. It is a global problem.

May 1, 2013

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By Zhong Zhang, Xijia Wu, Prakash C. Patnaik

"The integrated vehicle health management (IVHM) aims to provide life cycle management decisions for military platforms and their propulsion systems with reduced life cycle cost and increased operational readiness and safety. Among all the issues of IVHM, understanding the physics of failure and predicting lifetimes of the critical components are at the core: the decision makers have to know when and how components may fail in order to plan ahead. The difficulties to tackle failure problems lie in determining the material response to cyclic and dwell loading in a hot and/or corrosive environment, which all combined to induce multiple deformation and damage mechanisms, resulting in mix-mode failures. Decisions on component replacement (material substitution) and mission planning must be based on quantitative knowledge of the failure physics to mitigating the risk. This paper addresses the critical failure issues including creep, low cycle fatigue (LCF), thermomechanical fatigue (TMF); and presents a mechanism-based approach to life prediction. The mechanism-based approach, by its physics, is widely applicable over the entire operational spectrum of both structures and engines, and therefore is suitable for IVHM purposes."

Jan 1, 2015

By I. Caraconcea, M. Cousineau, S. Gariepy

"Several base metal plants operate in low grade/high tonnage conditions which impose strict cost control on all fronts for their operations to remain profitable. This leads to decisions regarding plant design, procurement, operations and maintenance that often favor cost minimization over value optimization. This may hinder the representativeness of the metal accounting systems while this should be a priority in a low margin environment. Such poor representativeness not only creates confusion in plant scheduling but can also hide suboptimal metallurgical performance. Furthermore, this situation can run undetected for a while since one dominant feature of a poor metal accounting system is its poor self-awareness. During their practice, authors have particularly identified measurement bias and reproducibility, as well as their impact on metal recoveries as areas of concern. These issues have not been extensively reviewed in the specific context of precious metals in base metal plants. Pragmatic solutions are proposed either at the design stage for a new project or to retrofit an actual operation. These solutions should be based on a business analysis that set a value of information matching the contribution of precious metals as well as the potential to use such information to act toward increasing plant profitability. Conclusions are that trade-offs are an inherent part of the design/audit/retrofit of any metal accounting system in any plant processing either base or precious metals. However, compromises must be evaluated on economic/technical ground.INTRODUCTION Every mineral processing plant must produce metal accounting reports (Morrison, 2008) where estimated saleable metal flows and inventories are published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimization, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that state of the art metal accounting is instrumental for mining companies to reach and sustain high-quality corporate governance (Gaylard, Randolph, & Wortley, 2014). However, producing a metal accounting report involves much more than just printing it (Lachance, Leroux, & Gariépy, 2015a). The underlying metal accounting system (Figure 1) is responsible not only for the reliable production of the metal accounting reports but also for the quality of the outcome. As such, the crucial tasks of its design/audit/retrofit should neither be seen as ancillary nor be left as an afterthought."

Jan 1, 2017

By M. W. Gilmore, J. Ndlovu, T. Sepoloane, Anglo American Platinum, L. R. Nelson, R. N. Varty, L. J. Bryson, B. Peyper, J. P. Hagemann

"As part of Anglo American Platinum’s Rustenburg Base Metals Refinery (RBMR) expansion, a new Nickel Electrowinning Tank House, with a nameplate capacity of 32 400 tons per annum, was constructed. Commissioning of the new electrowinning technology, which involved world first full deposit plating, commenced in 2011.The old nickel electrowinning process at the RBMR used starter sheets which, along with a divided cell configuration, was very labour intensive and exposed operators to high levels of aerosols that contained both nickel and acid. To overcome this problem two key design intents of the new technology are aerosol abatement and minimising labour in the electrowinning cell environment, with a design target to reduce the nickel occupational exposure limit (OEL) to half the legislated limit of 0.1 mg.m-3.Commissioning of the new technologies adopted to achieve mist abatement is described, together with a review of technical and operational challenges relating to the titanium blank edge strips, blank roughness and sandblasting optimisation, blank quality control, electrode spacing, polyconcrete cell dimensional stability and cell top furniture. The impact of these on process performance is presented and the development of fault checking and rectification methods, to maintain high process performance, is explained.INTRODUCTIONThe expansion of Anglo American Platinum’s Rustenburg Base Metals Refinery necessitated the construction of a new Nickel Tank House to achieve two primary objectives, namely increasing the nickel electrowinning capacity from 22 500 tons per annum (tpa) to 32 400 tpa nickel, and a design to reduce the nickel aerosols to 0.05 mg.m-3 as a time weighted average over 8 hours, which is half of the legislated occupational exposure limit (OEL) of 0.1 mg.m-3."

Jan 1, 2016

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By Hämäläinen M., O. Hyvärinen, E. Jääskeläinen

HydroCopperTM is a new hydrometallurgical process for the treatment of copper sulphide concentrates, which has been developed by Outokumpu. The process includes chloride leaching of copper concentrate, solution purification and precipitation of copper(I) oxide, an intermediate product, which is reduced and cast into copper products. The reduction can be carried out by pyrometallurgical methods or hydrometallurgically in an autoclave. This paper discusses the thermodynamic and kinetic aspects of the hydrogen reduction of copper(I) oxide in an autoclave. The results of the laboratory tests are presented and discussed. Finally, the autoclave method is compared with other options.

Jan 1, 2004

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By L. Drisdelle, S. Gendron

"Survival in today's business climate requires participation of all employees in a Total Quality Management Program encompassing everything - ""safety, quality of products, quality ofet1ch and every job done, and of course production "". We all know what needs to be accomplished, but struggle with how to do it, especially in an industry which has not always experienced management/union cooperation, and mistrust is still present.This paper describes a process to improve team work and employee involvement in Inco's nickel carbonyl refinery at Copper Cliff The process involves facilitatorship training for all employees, and a system for reinforcing and accomplishing the required behavioural change. The system is described in detail and a number of examples are presented. At the refinery, the staff is starting to understand as Max DePree recently wrote ""Without Quality Behaviour, you cannot have Quality Product"". IntroductionThe Copper Cliff Nickel Refinery (CCNR) is Inco's largest and most modern nickel refinery, which celebrated its twentieth year of successful operation in April 1993.The heart of the refinery is the Inco pressure carbonyl (IPq plant which produces high purity nickel pellets and specialty powders by refining an approximate 80% nickel granule feed. The carbonyl plant is a modem chemical plant with very special and demanding requirements for safety and environmental protection due to the toxic nature of the refining gas.Since 1987, there has been an emphasis at CCNR on a comprehensive Total Quality Improvement (TQI) Program which was designed based on recognizing customers' needs for improved systems for quality management. This program is customer oriented and comprises such elements as team organizational concepts, customer audits, process assessment and internal quality auditing.A detailed review of progress was made in early 1991 and it became apparent that the ""ownership"" of the TQI program was not broad based. In fact, the program was very much a staff driven effort and fell far short of total employee involvement and relentless continuous improvement that are now considered essential to remain competitive and stay in business.Inco staff has now come to regard that early phase of our TQI program as ""the technical aspects of total quality improvement"".The safety experience was also puzzling. Even though the safety statistics were good with an average lost time frequency of 1.6 for the last five years, the perfonnance improvement had plateaued and remained pretty much the same. Clearly a new approach was required if significant progress and continuous improvement was to be made."

Jan 1, 1994

By G. J. McTeer, D. L. Verhelst, D. J. Rioux

Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training and monitoring.

Jan 1, 2015