Search Documents

By Roger St. C. Smart, Paul Weber, Joan E. Thomas, William M. Skinner, Warwick Stewart, Stuart Miller

For mine sites affected by acid rock drainage (ARD) or with a potential future ARD issue, the prime consideration is not only the classification of different waste rock as potentially acid forming or non acid forming but also the peak acid (and metal) release rates and expected ARD duration during which effective ARD management and acid neutralisation capacity (ANC) are required. Methods for assessment of this ANC (e.g., Sobek tests) are already available but can be unreliable in ARD containing significant proportions of framboidal pyrite or iron carbonates. The measurement of negative ANC values and the release of S to solution showed that significant sulfide oxidation may occur prior to and during testing in samples containing reactive (particularly framboidal) pyrite resulting in serious underestimation of the original ANC. A simple methodology with dissolution in Ar-purged water before ANC testing, removing ferrous salts, and sulfate assay after ANC testing corrects these effects. Results also showed that a significant lag period (up to 432 h) may be needed for complete hydrolysis of Fe associated with the standard Sobek ANC testing of, for instance, siderite. Hence, the ANC of iron carbonates is usually significantly overestimated. By filtering and the addition of H202 until there was no subsequent pH drop (due to Fe hydrolysis reactions), followed by back titration to pH 7.0, the ANC for siderite was similar to the ANC determined after 432 h lag by the Modified Sobek ANC test and to the mineralogical carbonate ANCcarb determined by calculation based on electron probe micro-analysis. A chemical ANC calculation, based on neutralising cations released to solution, has provided a method to quantify the short-term ANC of carbonates and silicates in simple mixed mineral assemblages and waste rock samples. Results showed that silicate ANC can be more important in short-term neutralisation than carbonate ANC in low carbonate samples. In the longer-term, decreasing sulfate and metal loads with increasing pH values suggests that eventually sulfide acidity generation rates will match the longer-term inherent acid neutralisation rates of the sample derived from silicates. A kinetic ANC measurement for silicates, after steady state dissolution is reached, that indicates the number of hydrogen ions neutralised/m2/yr has been developed. These values can be used in estimates of the net acid production profile from wastes with low (and decreasing) pyrite content after the short-term ANC is exhausted.

Jan 1, 2004

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By R. Ghomashchi

Wear, fatigue and corrosion are the most widely encountered modes of failure in materials used in engineering applications, including aero-gas turbines. Although wear is distinctly classified as adhesive, abrasive, erosive, fretting and so on, there are usually more than one wear mechanism involved in the failure of components in service because there are many systems and materials variables active in materials wear that makes it more difficult to study. This is further complicated by the discrepancies between the results of laboratory tests and field data. The present investigation was set up to examine the wear characteristics of M50 and T1 high-speed steels at both room and elevated temperatures to draw a thorough understanding of the wear behavior of this class of high-speed steels. This article focuses on the mechanical and microstructural characterization of wear for T1 and M50 high-speed steels using a pin-on-disk wear machine.

Jan 1, 2005

By H. H. Wang

Construction safety documents regulate significant safety actions and requirements by which construction workers or employees should abide in order to secure them from occupational hazard events. Therefore, facilitating faster identification of applicable safety requirements from the documents has become an important topic in the construction safety domain. To address the need in this regard, tools and techniques have been developed and research efforts have been made. One of the research efforts is to utilize ontology, a knowledge representation and reasoning approach, as the methodology to achieve the goal of identifying applicable safety requirements. In such ontology-based researches, the development and construction of the safety concept ontology is an essential task as the concepts and the relationships between the concepts both representing key safety knowledge need to be carefully identified. In this paper, the author focuses on the safety documents without predefined concept structure and aims to address the concept and relationship identification difficulties. Specifically, the author leverages the Formal Concept Analysis (FCA) methodology, a theory of data analysis that identifies conceptual structures among data sets, to mine and analyze the documents in order to discover safety concept structure and to further assist the development of the concept ontology for the construction safety documents. The author expects the application of FCA to construction safety domain can eventually benefit the ontology-based approaches for identification of applicable safety requirements.

Aug 1, 2013

By D. G. Dixon

A novel technology for leaching copper from primary copper concentrates has been developed at UBC. This patented technology takes advantage of the galvanic couple between pyrite and chalcopyrite to ensure rapid and complete oxidation of chalcopyrite under mild conditions in acidic iron sulfate solution, without the need for microbes, ultrafine grinding, or chemical additives such as chloride, nitrate, or surfactants. Copper recoveries of 98% or greater can be achieved at 80°C under atmospheric conditions in as little as 4 hours of residence time. The process is selective for chalcopyrite over pyrite, generates near-quantitative levels of elemental sulfur, and is fully compatible with conventional solvent extraction and electrowinning of LME Grade A copper cathodes. In this paper, the fundamentals of the Galvanox ? process are reviewed, and selected results of batch leaching tests on various concentrate samples are presented and discussed.

Jan 1, 2007

"ALTHOUGH Canadian metallurgists have long been active in research, the scope of the work was somewhat limited until the be-ginning -of World War II. The rapid industrial development of Canada during the past ten years has been accompanied by .a similar upsurge in research. However, the wide geographical distribution of the research centres has made it difficult for the individual research workers to meet together and to exchange ideas or even to learn what projects .are being investigated or the nature and extent of the facilities available for work of this kind.The purpose of the present symposium is to assemble data relating to projects under investigation and the facilities employed at the various metallurgical research laboratories in Canada, thus providing some measure of correlation so that workers in different locations may learn what kind of work •is being .done at other points throughout the country.In reporting the symposium it has not been possible to reproduce the papers in full, but excerpts have been selected that give the essentia1 data."

Jan 1, 1952

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By Per-Lennart Nystedt

"The Boliden Lead Kaldo Plant for the treatment of lead bearing flue-dust from the Copper Smelter and the Slag Fuming Plant has been in operation at the Ronnskar Works of Boliden Metall since the middle of 1976. At the present stage, the plant can treat lead-bearing dust of different kinds and compositions. The process allows good separation of arsenic and halogens from lead.The flue dust from the Copper Smelter and the Slag Fuming Plant is very complex and, apart from lead, also contains zinc, copper, tin, bismuth, cadmium, antimony, arsenic, sulphur, silver, chlorine and fluorine. The metallurgical process has been developed by Boliden Metall and has been tested on a pilot scale at the Foundation for Metallurgical Research (MEFOS) in Lulea, Sweden.The pelletized dust is smelted in the converter, where the heat is generated by an oil oxygen burner. The second step consists of reduction with coke. A lead bullion and slag are obtained. The slag, transported in liquid form, is treated in the Slag Fuming Plant for the recovery of zinc. The third step is the elimination of arsenic from the bullion. This is achieved by treating the lead with iron (turnings or pellets). The result is a crude lead and speiss. The lead contains silver, tin, antimony and bismuth, and is suitable for the final refining stages in normal plant equipment for refined lead.For process control, we use the rapid analysis centre, which is pneumatically and electronically linked to 'all major plant sections and allows for a quick turn-around between delivery of the sample and feedback of results. All three steps in the process are performed in the same converter.Since the starting up of the plant, the original process has been subjected to some modifications. Initial problems related to equipment, maintenance and environment have been solved step by step. Examples are quoted. Recent operating particulars are presented."

Jan 1, 1980

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By Brock Morrison, Bernt Ling

"The Kiruna Electric System is an all electric ramp haulage system developed for underground mining. This electric truck haulage system is currently operating on three continents. This paper will review the technology of the system, existing installations as well as the economical benefits to the mining industry. The system was designed and developed to extend and exploit the economical advantages of ramp haulage. Performance information is provided. IntroductionThe Kiruna Electric System has been the subject of a number of technical papers over the past sever al years. During that period, the content of the presentations has changed from concept and theory to prototype testing to description of installed and operating systems.The intent of this paper is threefold:1. to present a brief review of the technical features of the Kiruna Electric Systems;2. to review the existing installations with performance data; and3. to provide a description of on-going developments within the Kiruna Electric Program during 1991.The Kiruna Electric is a high capacity ramp haulage system for underground mining operations due to an All-Electric Drive System, including two heavy duty electric traction motors. The high capacity of the K1050E results from three factors:• payload - 50 tonne• speed - 18 km/hr to 20 km/hr up a IS0J0 ramp (total resistance)• availability - over 90010 during a 12-month period"

Jan 1, 1991

By Brian Hart, Stamen Dimov, Aparup Chattopadhyay, Barun K. Gorain

"A novel gold deportment technique has been developed for complex copper-gold and double refractory gold ores using state-of-the-art technology. Characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulfide phases and variable proportion of visible and invisible gold in different sulfides and iron oxide phases.Double refractory ores are mainly composed of silicates and carbonates with moderate clay and mica, and minor amounts of sulfides and organic carbonaceous matter. Gold mostly occurs as ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Characterization of this carbonaceous matter, commonly known as TCM and quantification of gold associated within TCM, along with different sulfide and oxide phases is highly complex and challenging.Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy techniques, namely, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metal content in various species. The relevance of the mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2016

By Martin Encinas, Jesús L. Valenzuela, Jose R. Parga, Salvador Aguayo, Roy G. Lewis

Continuous laboratory solvent extraction of gold from cyanide solutions using LIX?79 guanidine based extractant has been investigated. Different variables that affected the selectivity and extraction include aqueous pH, extractant concentration, and modifier concentration. The extraction isotherms of the aurocyanide complex with respect to the other cyano anions were compared, and the following order of selectivity Au > Ag > Zn > Cu > Fe was observed. According to the pH isotherms, aurocyanide can be extracted in an alkaline media, and a better separation with respect to the other cyanoanions was obtained in the pH range 10.5-11.2. From the McCabe Thiele diagrams, better recovery was predicted when using LIX?79 extractant and tridecanol modifier at 10 vol.%. Stripping of the gold from the loaded organic was carried out at pH > 12 using NaOH and NaCN solution. The continuous tests indicate that a two-stage extraction followed by a single stage strip is adequate to obtain an overall process efficiency of >90%. Better results were obtained using a copper wash stage before gold stripping.

Jan 1, 2014

By K. Ghyselbrecht, R. Swennen, Y. W. Chiang, V. Cappuyns, R. M. Santos, T. Van Gerven, B. Meesschaert

Heavy metal contamination from mining and metallurgical activities of aquatic systems poses significant risk to the environment and human populations. The investigation of the distribution and immobilization mechanisms of heavy metals in sediments and soils has recently attained high priority. Different remediation methods can be employed to suppress or eliminate these contaminants. A tailored approach using both commercially available and in-house made adsorbents to rem ediate a heavy metal contamination site due to historical metallurgical activities in north Belgium is studied in this paper.

Jan 1, 2011

By T. Fliß

The protection of natural resources is of essential importance in times of rapidly increasing populations and resulting shortage of agricultural land. Soil and groundwater resources play a central role for the production of food or feed of any kind. The intensive agricultural and environmentally friendly use of these resources must ensure sufficient income and sustainability of life for future generations. Mining projects often represent a particularly deep intervention into ecosystems due to their size as well as the most expensive treatment processes. Conventional mines comprising of shafts and developed mining fields require the stockpiling of waste rock and in particular to potash mining, the discharge of brines from raw salt processing. In contrast, mining operations based on the solution mining method can be operated without major environmental impacts and lower security risks. While the solution mining for the production of rock salt finds application since more than 500 years, exist a procedure to produce potash using solution mining only since the 1980's. For solution mining drill holes are used to exploit the potash, launched from the surface into the deposit. The exploitation of the raw material occurs by the dissolution of the potash injecting solvents and creating so-called brine caverns. Currently, a number of mining projects in Carnallite deposits by the solution mining method are in progress around the world. Often these projects are located in sensitive ecosystems. K-UTEC project and support actual a solution mining operation of a Carnallite deposit for a Chinese customer in South-East Asia. This work comprises a comprehensive geological and geomechanical modeling as well as stability analyses. Furthermore the cavern design and brine field layout as well as the planning of the brine processing and the plant design. The present paper introduces this project as a case study. The application of a special solution mining procedure and processing design ensures an emission-free mining operation (Zero Disposal Plant). The emission-free operation is achieved by utilizing the full extent of the caverns to dispose the liquid solutions from processing. The presentation of principal salt processing and technical equipment will be rounded by information about the geology of the deposit. Since the deposit includes a number of sensitive minerals, such as Tachyhydrite and Bischofite the presentation comprise a lot of interesting items with special view at the brine field operation. K-UTEC designed and delivered a special blanket measuring system and a well cement according the request of the customer. K-UTEC, a research and engineering company with more than 60 years of experience in the sector of potash and rock salt mining, developed the world's first solution mining operation for Carnallite in Germany more than 30 years ago. In recent times K-UTEC served in different solution mining projects worldwide, with special view at the environmental impact, as well as the optimal utilization of the deposits.

Aug 1, 2013

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By Xiaoqi Sun

"Rare earth elements (REEs) have a series of specific properties making them invaluable in products including lighting, electronics and magnetism. The elements have been used in many commercial products, for example, turbines, electric vehicles, batteries, lighting, computers, cell phones and lasers. Heavy REEs are attracting the interests of scientists from many countries, and these elements have become critical to develop high-tech materials. Ion-adsorbed rare earth deposits were first discovered in China. The minerals are also called weathered crust elution-deposited rare earths. The particular types of deposits are distributed throughout southern China. The ion-adsorbed deposits are rich in medium and heavy REEs, accounting for more than 80% of the world’s total medium and heavy REEs production. However, the separation of heavy REEs from ion-adsorbed deposit is difficult owing to their similar chemical properties. The conventional separating technologies have caused serious pollution. A novel extraction strategy has been developed in this laboratory and is presented herein.INTRODUCTIONThe unique properties of rare earth elements (REEs) render them important in high-strength magnets, lighting phosphors, polishing compounds, and ceramics. Especially for applications that take advantage of the f-orbital electrons, substitutions outside the REE family are often difficult to impossible (Nassar, Du, & Graedel, 2015). Extracting and separating individual elements from mined ore is not easy, requiring lengthy operations to separate them, and this results in high costs and adverse effects on the environment. The low concentration of REE in the earth’s crust makes economic exploitation difficult (de Boer & Lammertsma, 2013) and the sustainability of the REEs separation industry has aroused considerable attention (McLellan, Corder, Golev, & Ali, 2014). To eliminate protons and break the dimmers in organic phosphonic acids or carboxylic acids, the saponification of acidic extractants by acid-base neutralization reactions are widely used in industrial REEs separation (Sun, Luo, & Dai, 2012a). The saponification procedure contributes to increased extractability and selectivity of acidic extractants to a considerable extent. The common industrial saponification mechanisms and technological processes are shown in Figure 1 and include ammonium saponification (saponified by NH3·H2O), sodium saponification (saponified by NaOH), calcium saponification (saponified by Ca(OH)2), and magnesium saponification (saponified by MgO). These inevitably result in wastewaters containing NH4 +, Na+, Ca2+ or Mg2+ because of the cation-exchange extraction mechanisms (Xiao, Long, Huang, Feng, Cui, & Wang, 2013; Song, Fu, Wang, Liu, Zhou, & Li, 2014; Sun & Waters, 2014)."

Jan 1, 2016

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By J. Zhou1

"The extractive metallurgy of gold ores is largely driven by their grade and mineralogy. The concentration of gold in the crust is extremely low and highly variable, resulting ore variability in many gold and copper-gold deposits. More importantly, gold in an ore may occur in two or three forms (i.e. microscopic gold, submicroscopic gold and surface gold), making gold ore processing extremely challenging. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes. The objective of gold geometallurgy is to reduce and minimize the technical risk in project evaluation, plant design, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical and metallurgical testwork. Gold deportment study is a powerful tool in characterization of various gold ores. Effective and quantitative gold deportment results are critical and useful for predicting gold recovery and building geometallurgical models of gold ores. This paper provides an overview of geometallurgy fundamentals and applications in gold processing, with a focus being on the ore characterization and gold deportment study.INTRODUCTION Geometallurgy is an inter-disciplinary approach which links the geological, geochemical and mineralogical characteristics to the metallurgical performance of an orebody. Combined with mine planning, it has been used in scoping, prefeasibility and feasibility studies, process design and optimization of gold, copper-gold, copper-moly, nickel and iron projects among others (Williams & Richardson, 2004; Dobby, Bennett, Bulled, & Kosick, 2004; Bulled, 2007; Bulled, Leriche, Blake, Thompson, & Wilkie, 2009; Kormos, Sliwinski, Oliveira, & Hill, 2013; Muinonen, Sciortino, Korczak, & St-Jean, 2013; Leichliter & Larson, 2013; Leichliter, Jahoda, & Montoya, 2013; Hatton & Hatfield, 2013; Baumgartner et al., 2011, 2013; Hoal, Woodhead, & Smith, 2013; Zhou, 2013). The goal of a gold or copper-gold geometallurgical program is to characterize and understand the metallurgical variability of an orebody, such as comminution, gravity, flotation and cyanidation parameters and metal recoveries, and to build a geomet model which can be used to assist in mine planning and to predict the plant performance. In any geometallurgical program, representative sampling is the key to ensure the results of a geometallurgical study will reflect future performance once the plant is commissioned. Geometallurgy compliments, but does not replace, the traditional mineralogical and metallurgical approach during the development and operation of a gold or copper-gold project. Geometallurgy is a methodology for testwork design and a framework for mine planning. The first part of this paper provides an overview of geometallurgy fundamentals and application in gold ore processing."

Jan 1, 2017

By G. Goodall, M. Muinonen, R. Pandher, R. Jabbar, S. J. Muinonen

"The implementation of a new and highly efficient converting practice at the Glencore Sudbury Integrated Nickel Operations Smelter has opened the possibility to further capacity increases by using larger ladles. To quantify the impact of increasing ladle sizes from 200 to 300 ft3, XPS constructed a detailed discrete event simulation using the commercial software package Rockwell Arena®. The challenges associated with implementing a model on an intricate and tightly scheduled process, and the solutions needed to derive meaningful results will be presented. The aisle capacity is predicted to increase by approximately 17 %, with a reduction in furnace tapping demand of 8 %. Arena modeling capabilities and the key factors contributing to the overall capacity increase at the Sudbury INO Smelter will be reviewed and presented.INTRODUCTION The Glencore Sudbury Integrated Nickel Operations (INO) comprises two Ni-Cu-PGM mines, Strathcona Mill, and the Sudbury Smelter. The Smelter has operated continuously since 1929 using different processes to produce nickel-copper Bessemer matte. Feeds to the Sudbury INO Smelter are a blend of concentrate from Strathcona Mill, Raglan concentrate produced at the mine-mill complex in Raglan, Quebec, as well as third party concentrate feeds shipped to Sudbury from around the world. In 2016, the Sudbury INO Smelter produced 75,900 tonnes of nickel and 20,000 tonnes of copper in Bessemer matte. The product matte is shipped to Glencore’s Nikkelverk refinery in Kristiansand, Norway where it is refined to produce nickel and copper cathode. A schematic of the Sudbury INO Smelter’s flowsheet is shown in Figure 1."

Jan 1, 2017