Search Documents

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938

By S. Kelebek

Batch flotation tests were carried out using samples from stockpiles that were up to 1.5 months old as well as fresh samples oxidized in the lab for up to six months. Head grades and size distributions of samples were equalized whenever possible. The samples from stockpiles and oxidation experiments produced inferior nickel grade-recovery compared to the fresh sample. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to complete flotation of pyrrhotite. Secondly, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite. Application of a high pH of 10 compared to the regular pH of 9.2 slowed down pyrrhotite flotation kinetics, but was not able to prevent complete flotation after 8 minutes. The samples oxidized in the lab did not match full characteristics of stockpile samples. They provided somewhat better selectivity for pentlandite. Some correlations were observed on a qualitative basis between surface characteristics such as elemental sulphur formation, activation and flotation behaviour. Oxidation conditions, which induce floatability on pyrrhotite while causing incremental loss in pentlandite floatability appear to be the root cause of difficulties in the processing of oxidized forms of these ores.

Jan 1, 2006

By José J. Suárez

Abstract: Globally, the mining industry is expected to face the following challenges through 2020: 1. Sustaining growth amidst fierce competition 2. Containing cost increases and managing through the cycle 3. Attracting and retaining talent 4. Managing environmental concerns and improving sustainability 5. Managing volatility risks in commodity markets Our experience and research reveals that the higher performing global miners are adopting many of the following strategies: (1) Adopt a Global, Agile Operating Model (2) Be the Developer of Choice (3) Drive Capital Efficiency (4) Be the Employer of Choice (5) Integrate the End-to-End Business Model (6) Move to the Virtual Mining Value Chain This paper/presentation will provide data obtained through research on five (5) challenges facing the mining industry, and on the six (6) strategies that high performing global miners are adopting.

May 1, 2013

By J. M. Toye

The Canadian nuclear fuel business relates primarily to supplying fuel for Candu reactors. The product development, manufacturing and marketing activities of our nuclear fuel industry will therefore be determined by the rate of growth of the Candu nuclear reactor business. The nature of this relationship between the Canadian nuclear fuel industry and the Canadian Heavy Water Reactor program will be considered, with particular reference to the factors influencing future economic growth.

Jan 1, 1969

By A. H. Onur

Spontaneous combustion of coal is a significant hazard in underground coal mines. It causes serious problems for miners for many years after the fact. It threatens workers? lives and causes economic losses for companies. It disrupts coal production and makes it necessary to abandon the main drift where the spontaneous combustion occurred. Coal fires have to be prevented before they occur; otherwise they are very hard to control. Precautions thus have to be taken in potentially risky areas. For coal to spontaneously combust, it needs 3 elements: fuel, oxygen and heat. If one of them is missing, the fire cannot occur. The best way to prevent spontaneous combustion is to prevent contact between coal and air. Coating of the coal surface with an air-proof lining material would be a practical and useful solution to prevent spontaneous combustion of coal. In the scope of this study, a lining material for coating the coal surface was designed at laboratory conditions. Lining material to be used for preventing coal fires should be airproof, cheap, sufficiently strong, have low rebound, be water- and heat-resistant, and easily obtained and applied. It should also be safe for human health when in contact with mine ventilation. By considering these obligations, 3 kinds of gypsum (plaster, satin plaster, molding plaster), as well as lime, cement and fly ash and different mixtures of these materials were applied in laboratory conditions to form a lining material. Samples of lining material were subjected to uniaxial compressive strength tests to determine their behavior against roof loads. Although there is no need to carry any roof load, the lining material has to be sufficiently strong to stay in place on the applied surface. If the lining material is broken, coal and oxygen can react again. Air permeability and curing time of the mixtures were also tested in laboratory conditions. Then the tested mixtures were applied on a wall with a pump to test the applicability of mixtures. After all tests were performed in laboratory, the most suitable mixture was determined as the optimal lining material to prevent coal fires.

Aug 1, 2013

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By L. E. Young

"The Red Dog deposit of the western Brooks Range, Alaska was discovered in the 1970s. Two mineralized areas are present, the Main and Hilltop deposits. With indicated and inferred reserves of 77 million tonnes of 17.1% zinc, 5.0% lead and 82 g/ tonne silver, the Main deposit of Red Dog represents one of the world's largest zinc-lead deposit s. Since serious evaluation by Cominco commenced in 1980, a better understanding of deposit geology has been gained through 10 715m of diamond drilling and concurrent geologic, geophysical and geotechnical studies. The Red Dog deposit is of Mississippian to Pennsylvanian or Early Permian age, and straddles a redox transition in fine-grained and chemical sediments of the Red Dog structural sequence.The Main deposit has been modified by regional Mesozoic thrust faulting and isoclinal folding, resulting in complex interrelationships between silica rock, sulphide rock and barite. Multiple lines of evidence suggest the Main deposit contains both a syngenetic stratiform and a replacement component. Ore fluids were probably derived by regional lateral movement of brines through a coarse clastic footwall aquifer, then upwards along block faults to the site of the Red Dog deposit.Historical PerspectiveThe region in the vicinity of the Red Dog deposit (Fig. 1) was first prospected by J. W. Kelley in the late 1880s (Orth, 1967). The first coordinated inland exploration was conducted by the U.S. Geological Survey in 1910-1911 and 1923-1926 (Smith, 1913; Smith and Mertie, 1930). The earliest reports of zinc-lead mineralization in the region include reference to samples collected at unknown locales by Eskimo prospectors (Anderson, 1944). In 1955 stratiform pyrite was discovered 19 km west of Red Dog by I.L. Tailleur of the U.S. Geological Survey (Tailleur, 1970). The first reported visit to what is known as Red Dog was by I.L. Tailleur in 1968, who was field checking a colour anomaly noted by B. Baker, a local bush pilot (Tailleur, 1970; Moore et al., 1986) ."

Jan 1, 1989

By F. -Z. Ji, G. A. Irons, M. Barati, K. Coley

The use of oxygen in electric arc furnace steelmaking is tied to the use of fossil fuels, and slag foaming. The current work examines the kinetics of carbon injection into EAF slags especially the saturation injection rate and available reaction area in the slag foam. Based on individual rate data and experimental gasification rates of carbon in the slags, the available reaction surface area in the gas bubbles was found to be around 1900¬4700 cm2.kg-slg-1 for carbon injection into EAF like slags at appropriate injection rates and steel making temperatures. The ratio of number of bubbles to number of particles is 1 to 17 and the weights of carbon per unit reaction area are 0.001-0.008 gC-cm-2. Using the relationship between active reaction area and x supplied in this study, the gasification rates of carbon in slags can be estimated with gas-slag interfacial reaction rates.

Jan 1, 2004

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By W. Hunka

PACIFIC PETROLEUMS, Ltd. first discovered commercial quantities of gas in the Peace River area in 1952. Development of gas wells in this area is quite ex-pensive due to low penetration rates. To improve the economics, the potential of the wells in many cases had to be increased. At that time, well stimulation was still in its infancy in Canada and in this area, in particular, no treatment of any consequence had been attempted. Therefore, trial-and-error was the only means available to determine the stimulating technique that would give optimum results. Various fluid treatments were available and these were used wherever the application was warrant-ed. This paper covers acid fracture and explosive treatments as carried out on various gas-bearing horizons.

Jan 1, 1958

By C. G. Anderson

As the global demand for copper and gold steadily increases and the need for environmentally sound processing also grows, successful hydrometallurgical treatment of enargite (Cu3AsS4) concentrates has come to the forefront. This type of concentrate contains considerable arsenic so that successful arsenic fixation, for example as scorodite, is of the essence. This paper outlines the successful application of low temperature and low pressure nitrogen species catalyzed (NSC) hydrometallurgical pressure oxidation of enargite concentrates. The successful stabilization of the arsenic as an iron arsenate compound is discussed. Also, the use of experimental design software is highlighted as a process application and optimization tool.

Jan 1, 2006

By M. Maley, S. Burling, R. Ring

ABSTRACT The numerous global uranium deposits vary significantly in mineralogy, grade, and textural characteristics; therefore, information from traditional (or conventional) sources on the fundamentals of leaching uranium and gangue minerals is not always applicable when studying particular ores. Empirical studies can be effective in understanding leach systems and can lead to improvements in process design but there remains a lack of fundamental understanding necessary for ongoing process optimization as ore bodies continue to vary. ANSTO Minerals has undertaken a work program to address several fundamental questions about uranium leaching, including the unexpected impact for some ore types of leaching at high oxidation potential.

Jan 1, 2012

By Boris Yacksic, R. W. Bruce

"The flotation of a cassiterite ore with oleic acid will recover primary or rougher concentrates assaying over 10 per cent Sn, with a recovery of 80 to 90 per cent. These rougher concentrates cannot be up-graded to a marketable grade by normal reflotation. Experiments were conducted on low-grade tin ores, and a process was developed for up-grading the rougher flotation concentrates by a reverse flotation technique. The process was tested on a number of samples of ore from the Catavi mine in Bolivia. The results of these tests showed that a concentrate assaying 40 to 60 per cent Sn could be readily produced, with a recovery of 60 to 75 per cent of the tin in the ore."

Jan 1, 1967

By W. G. Hubler

History The Aldermac mine is situated on the Nipissing Central railway near the ' centre of the township of Boischatel, Quebec, and is about ten miles west of Noranda. Aldermac Mines, Limited, is a subsidiary company of Towagamac Exploration Company. The property was staked by Messrs. Alderson and MacKay and McMartin, during the winter of 1922-23. During October, 1925, a copper discovery was made by K. W. Fritzsche, who was in charge of exploration work at that time, the first trench on this discovery averaging 8 per cent copper over a width of ten feet. This led to the discovery of another body 200 feet to the north, with an average of 3 per cent copper over fifteen feet in width. A magnetic survey was then carried out which led to the location of the large pyrite ore-bodies which have been developed in the past few years. Development work was carried on to a depth of 1,125 feet, and approximately three million tons of massive pyrite ore was indicated. Extensive metallurgical tests were conducted in the laboratories of the Mines Branch of the Department of Mines at Ottawa to determine the proper metallurgical treatment and the economic possibilities of the ore. Owing to the comparatively low copper content, and the uncertainty of the copper market, it was doubtful if the mine could be profitably operated for the production of copper alone. Messrs. Alderson & MacKay, however, realized the possibility of utilizing the large tonnage of pyrite as a substitute for native sulphur, 'which in past years has been imported into .Canada for the manufacture of acid and sulphate pulp in paper mills. They therefore organized the Sulphite Research Corporation with the object of developing an economical process of utilizing the pyrite.

Jan 1, 1932

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005