Search Documents

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By Changyoon Kim

Technological advances in mobile systems, such as smartphones and tablet computers, provide engineers with new opportunities to enhance the current facility management processes. Equipped with powerful system processors, touch screens, and wireless communication capabilities, mobile systems enable the experience of omnipresence of facility information. Building information modeling (BIM) also enables improvements in facility management. With an advanced data structure and visualization capacity, BIM can be used in numerous applications for facility management. This study aims to incorporate the strength of mobile systems and BIM in facility management. The proposed system, which utilizes smartphone technology, allows engineers to conduct facility management functions, such as maintenance planning, inspection, and assessment, irrespective of a user?s location. The integration of building information modeling in a system provides detailed visual information of the building components. A case study was conducted to verify the applicability of the mobile system in terms of the hardware functions, system design, and user interface. This proposed system, with its study results, provides a guideline as to how mobile systems can be effectively integrated with BIM for improved management of facility information.

Aug 1, 2013

By M. Sakamoto

Copper foil is an indispensable material for Printed Circuit Boards (PCBs). PCBs in turn are essential elements of all electronic equipment today and thus important for our living in the new age of IT. The requirements from the copper foil market have lately been increasingly strict and diversified due to the rapid technical advancements in miniaturized high-density electronic equipment and highly integrated semiconductors. Tight control of thickness, metallurgical properties, surface morphology and characteristics is needed. In this paper, both electrodeposited copper foil for PCB and rolled copper foil for the flexible printed circuit board are discussed, and the recent technical developments in these copper foil products are reviewed.

Jan 1, 2007

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

By Deborah McCombe

"and Bill Roscoe, Consulting Geologist and Principal with Scott Wilson Roscoe Postle AssociatesMineral property valuations are carried out for a variety of reasons, such as mergers and acquisitions, non-arm’s length transactions, initial public offerings of stocks, support of audited financial statements, fairness opinions, determination of vendor considerations, litigation, expropriation, income tax matters and insurance claims.The CIMVal Committee was formed in 1999 to review and advise on approaches to the valuation of mineral properties. CIMVal is a special committee of CIM formed on the recommendation of the Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission.After solicitation of views and consultation with various interested parties, the CIMVal Draft Standards and Guidelines for Valuation of Mineral Properties were released for comment in February 2002 and were finalized in February 2003. CIMVal’s objective was for the standards to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges. To that end, the standards contain many of the definitions and concepts of National Instrument 43-101, Standards of Disclosure for Mineral Projects, which came into force in February 2001.The intent of the CIMVal Standards and Guidelines is that mineral property valuations be carried out by appropriately qualified individuals and that all relevant information be fully disclosed. It consists of two parts: standards, which are mandatory in the valuation of mineral properties, and guidelines, which elaborate on the standards and provide guidance and recommendations for the valuation process and for reporting."

Jan 1, 2003

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By P. Mottahed, E. De Souza

One of the major unsolved problems of safe, economical roof support in the evaporite industry has been that of obtaining and maintaining anchorages in relatively soft rock. This is due to the viscoelastic and viscoplastic behaviour of salt rock and associated deposits. This paper introduces a low-cost, yieldable support mechanism, consisting of a system of buckling disks, which provides viable solutions to dynamic support. The yieldable support system offers a number of advantages in comparison with existing dynamic support systems. It is characterized by its simplicity in design and installation, repeatability in behaviour and cost effectiveness. It also has the added advantage of providing the operator with a means of assessing support behaviour and ground performance by direct visual observation of changes in disk shape. Thus, the system can be utilized as a warning mechanism of ground stress and support load conditions. Such system not only provides a feasible and more effective rock mass stabilization strategy but improves mine safety.

Jan 1, 1999

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By S. Qian

Galvanic corrosion is a potentially major concern associated with the application of stainless steel reinforcement which is in direct (electrical) contact with carbon steel reinforcement in concrete structures. Judicious use of stainless steel rebar in both new construction and rehabilitation of older structures is a viable, cost-effective option for extending service life and reducing maintenance costs. Questions, however, had arisen about the possibility of increased corrosion due to galvanic effects. This paper investigates the galvanic-coupling behaviours of three different types of stainless steel and carbon steel. Tests were performed both in electrochemical cells and with specimens in concrete inside an environmental chamber. The results show that oxygen reduction on stainless steel is the rate-determining factor for galvanic coupling of these two metals. It is much lower than that of passive carbon steel. As a result, the galvanic coupling of stainless steel with carbon steel will not increase the risk of corrosion of carbon steel reinforcement.

Jan 1, 2005

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By Robert Halupka

The industrial minerals sector represents a broad range of products involving a variety of technologies serving a diversity of markets and end uses. Unit values of products vary widely, reflecting the peculiarities of each product/market sector. Generalizations are therefore understandably difficult to make and borrowers may need to take extra time to "educate" lenders on the key aspects of their business and industry sub-sector. This paper will examine the factors and the thinking that lenders apply when considering financing proposals to companies in the industrial minerals sector. If you understand the lender's perspective and their concerns, then you can make better use of your own time and resources when arranging financing for your company or project.

Jan 1, 2001

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By Mikael Ramström

In 2002 Atlas Copco Rock Drills AB released the new RCS technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging and reduction in manpower in some types and serviceability, have all taken a quantum leap forward when compared with previous generations of drill rigs. The RCS (Rig Control System) is modularised and distributed is accomplished by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions.

May 1, 2003

By Eric R. Skonberg

"Technology exists today to blind drill a mine shaft 20 feet in diameter, unlined, over 3,000 feet deep. These shafts must be lined in the most economical, safe and expedient manner possible. A new technique of stacking precast concrete cylindrical sections in the unlined shaft has been developed to yield a dry and hydrostatically lined shaft .These sections must withstand an external radial pressure of 3,000 feet of water yet take up as little room as possible in the shaft . Using high-strength concrete, wall thicknesses may be kept at 2 feet. The outside diameter of the sections has been chosen to be 18 feet to allow for some annular space between the liner and shaft wall. The concrete sections are produced in segments 10 feet long weighing 75 tons each. During drilling operations, the concrete sections are cast and cured. After drilling operations are complete, a headframe is situated over the shaft. The unlined shaft remains full of fluid. A special liner running tool is mated with the section in three steel ports at the bottom of the section. The section and running tool are lowered into the hole, and the tool is disconnected and returned to the surface. Subsequent sections are lowered and stacked using the same operation. Grout is placed behind the liner to result in a dry shaft."

Jan 1, 1981

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By M. W. Mikhail, R. J. Mikula

"Funding has been made available through the National Energy Program to build a mobile fine coal treatment plant. The plant is intended f or field application and also to upgrade the existing pilot plant facilities.Western Canadian coals with high proportions of fines (due 10 their friability) cause high losses of fine coal to the reject and in turn reduce the over-all recovery of saleable coal. Eastern Canadian coals with high amounts of sulphur of ten require crushing to fin e sizes to liberate pyrite and therefore need effective and efficient separation of these fine sulphur particles. The difficulties involved in solving these problems are two-fold. One is the reluctance to experiment in an operating wash plant and the other is that laboratory scale testing often cannot be extrapolated to the plant environment. The mobile fine cleaning plant with its ability to operate at existing coal preparation plants across Canada and with its flexibility in implementing flowsheet option s and close monitoring of fine coal circuit variables, is ideally suited to solve these fine coal cleaning problems. The mobile plant objectives are to design and optimize flowsheets, evaluate and improve fine cleaning circuit operations and 10 lest new process monitoring and control equipment.The schedule for construction and the required resources will be outlined along with flowsheet options and the general R&D philosophy of the mobile plant.IntroductionIn relation to coal preparation technology, Canadian coal s can be grouped as Eastern coal, Rocky Mountain metallurgical coal and Foothills high volatile bituminous coal. The eastern coals have high sulphur contents and in some cases require crushing or even grinding to liberate the fine pyrite . Rocky Mountain metallurgical coals often occur in highly sheared seams which have been subjected to rapid coalification. The high friability of these coals means that degradation during mining, handling and processing is extensive and results in large amounts of fine s ranging between 20 and 60% by mass of the wash plant feed. The widely varying geo logical structure and exposure to the elements results in partially oxidized coals which perform inconsistently in the traditional method of fine cleaning by flotation . Foothills high volatile bituminous coals for thermal use are frequently interbedded with soft shales and bentonitic clays. These clays disintegrate during washing and swell, producing large volumes of tailings. The presence of clays in plant circuits, particularly fine circuits, tends to increase the viscosity and may cause deterioration of the fines density separation and increase magnetite losses. In view of the fact that fine coal cleaning is the most difficult aspect of coal preparation , a research program is being established to study the factors involved and to offer some solutions.A recent performance evaluation of Canadian washeries showed that yield losses in the minus 2 mm coal circuits were approximately ten times those occurring in the coarse coal circuits(1). Because 2 mm x 0 coal represents 30 to 70 per cent of the raw coal, these losses can be considerable . The operating and capital costs of beneficiating minus 6 mm coal are about four to five times higher than for plus 6 mm coal. In the case o f minus 2 mm coal the costs are even higher. The economic importance of the fine coal cleaning cannot be over emphasized and as a result, the CANMET R&D program is geared for fine coal beneficiation."

Jan 1, 1984

By A. Vervoort, A. Govaerts

Geostatistical concepts are often difficult for students to understand, even those with a strong mathematical background. One of the main problems is the link between the variation of the parameter value in space or time and the calculated experimental semivariogram. Another challenge is differentiating between directional and omnidirectional semivariograms and their interpretation. For these reasons, interactive tools were developed based on the free public domain software R. The use of these interactive tools is limited to educational situations only (i.e., to visualize basic concepts). The interactive modules can be accessed at www.bwk.kuleuven.be/geostatistics.

Jan 1, 2014

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012