Search Documents

By J. J. Hussey

"Abstract-The ""Brunswick Horizon"" an informally named ore-bearing unit near the top of the Nepisiguit Falls Formation in the Ordovician Tetagouche Group, hosts the Brunswick No. 6 and No. 12 base-metal mines, as well as the former Austin Brook iron mine, in northern New Brunswick. Detailed structural analysis of the No. 6 and No.12 mines led to the prediction that a massive­ sulfide deposit may have been repeated by F1 folding along the Brunswick Horizon. A subsequent drilling program discovered the new massive-sulfide North End Zone at a vertical depth of 1100 m, 1 km north of the No. 12 underground workings. By the end of 1990, Zn-Pb-rich massive sulfides had been delineated over a strike length of 200 m and a down-dip extent of 170 m. Rock units intersected in the North End Zone are generally thinner and vary somewhat from those at the Brunswick No. 12 mine. Thinning of the hanging wall rocks may be primary, may result from attenuation along F2 folds, or may represent truncation by a thrust fault. The newly discovered sulfide zone indicates that significant potential exists for the discovery of other deposits at previously unexplored depths.SOMMAIRE-Dans le nord-est du Nouveau-Brunswick ""l'horizon Brunswick"" est le nom usuel de la zone qui contient les mines de métaux de base Brunswick No. 6 et No. 12, ainsi que l'ancienne mine de fer Austin Brook, toutes situées sur le dessus de la Formation ""Nepisiguit Falls"" dans le Groupe Tetagouche d'âge Ordovicien. Une analyse détaillée de la structure des mines No. 6 et No. 12 à permis a van Staal de prédire qu'un gîte de sulfures massifs pourrait se répéter dû à une déformation F1, au nord de Brunswick No. 12. Suite à un programme de forage, la nouvelle zone de sulfures massifs appelée le ""North End Zone"", profonde de 1100 rn, et à une distance d'un km au nord des chantiers souterrains, fut découverte vers la fin de l'année 1990, les sulfures massifs riches en Zn-Pb ont été délimités sur une longueur de 200 rn et une hauteur de 170 rn le long du pendage. Les unités de roches intersectées dans le ""North End Zone"" sont généralement plus minces et sont quelque peu différentes de celles de la mine Brunswick No. 12. L'amin­ cissement des roches pourrait être primaire ou être le résultat de l'atténuation le long des plis F2, ou soit tronqué par une faille. La nouvelle découverte d'une zone de sulfures indique un potentiel énorme pour la découverte d'autres g ""tes à ces profondeurs inexplorées."

Jan 1, 1992

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019

By R. J. T. Charles

Introduction An apparatus that will measure the surface area of a few of the simple minerals with a high degree of accuracy has been described by J. W. Bell (1). His apparatus consisted essentially of a photometric device that would measure the turbidity of fine particle suspensions. Turbidity, in this case, was considered as a function of surface area. Bell's method of surface area determination seemed to offer possibilities of extension and improvement to the point where it might approach a general method of particle size measurement. Theoretical and Practical Considerations of the Photometric Method In order to illustrate how turbidity may be considered as a function of average particle size, and to indicate the type of results expected from a photometric method of particle size measurement involving turbidity, the following theory may be hypothecated. If a number of particles, considered as spheres of uniform diameter, are placed at random in the path of a beam of light, the following expression, which will give the change in light intensity as a function of the diameter of the particles, the specific gravity of the material, and the weight involved, can be formulated from the Beer-Lambert Law:

Jan 1, 1951

By H. L. Cheng, C. H. B. Leitch, C. T. Hood, A. J. Sinclair

"Epithermal Zn-Pb-Cu-Ag-Au quartz-carbonate-barite veins at the Silver Queen mine near Owen Lake, west-central British Columbia, are hosted by Late Cretaceous Tip Top Hill andesitic volcanic rocks. The veins form a rectilinear northwest-northeast pattern that differs slightly from regional structural trends. The main northwest-trending veins are oriented very close to the trend of regional northwest faults, but the crossing veins tend to be more east-north-easterly (070 degrees)compared to a regional north-easterly trend (040 degrees). The character of the veins suggests they are extensional features formed by dextral slip related to Paleogene oblique subduction, or intrusion of magma at depth, or both.In detailed exploration at the mine, the veins cannot be modelled as simple tabular sheet-like bodies. Instead, they are complex structures that divide and rejoin, forming multiple veins or stringers, or are found in shear zones as replacement features with quartzsericite- clay-carbonate-pyrite alteration haloes of variable width that make definition of vein margins and correlation from hole to hole ambiguous. In addition, individual veins within each of the main structures have en echelon characterboth along strike and down dip.Geological and assay data must be carefully studied to define the margins of these complex veins before any estimation of ore reserves may be made. Where multiple veins occur in a section, ore/gangue mineralogy, assays, character of wallrock alteration, and thickness of vein and mineralized hangingwall, median and footwall zones must be used to evaluate continuity of mineralized structures. Well-defined sections are projected into areas of increasing complexity. Once the vein boundaries are defined, metal concentrations, important metal ratios(Au/Ag, Pb/Zn, Cu/Zn), and true thicknesses of the vein provide the basic data for reliable ore reserve estimation."

Jan 1, 1991

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By Claude Hubert, Robert Sansfaçon

"The Malartic gold camp includes the Malartic Gold Fields, Barnat, East-Malartic, Canadian Malartic and Sladen mines. From 1935 to 1984, these mines have yielded 212 403 kg of gold. They occur within a 900 m wide belt of highly sheared, dislocated and faulted volcanic and sedimentary rocks (Piché and part of the Pontiac groups) herein named the Malartic Tectonic Znne (MTZ). The zone trends WNW-ESE and separates two lithotectonic sedimentary domains, the Cadillac to the north and the Pontiac to the south. The sedimentary domains are characterized by their coherent fold generations consisting of open to tight reclined and recumbent F1 folds that have been refolded into series of asymmetric upright F2 folds. A flat-lying schistosity (S1 ) and a vertical pressure-solution cleavage (S2) are ubiquitous throughout. Discrete sets of brittle and brittleductile faults are synchronous and parallel to each of these two fabrics.The MTZ trends N320° in the northwestern sector of the town of Malartie, changing to N2800 at its easternmost extremity. The Malartie and Sladen faults constitute its northern and southern boundaries respectively. These two faults also bound another set of faults oriented N305°. Throughout the MTZ, the faults at N280° and N320° and those at N305° outline a series of anastomosed motifs that constitute the principal structural feature of the Malartic district. Locally, a fourth set of minor faults at N065° combines with the other three prominent sets. All these faults have disrupted the gold-bearing volcanic, sedimentary and intrusive rocks encountered throughout the MTZ.The MTZ comprises numerous lozenge-shaped blocks of komatiites and basalts or greywackes and black shales which are cut by disjointed dikes, sills and small intrusions of felsic and mafic rocks. The latter includes gabbro, diorite, lamprophyre, monzonite and pegmatite. They frequently fill conjugate sets of fractures. In some areas, they are clustered into coalescent intrusions. The present morphology of these intrusive bodies( cube, chocolate-tablet boudin, parallel epiped and cigar) is not representative of their primary forms but the result of late shearing and faulting indicative of a major tectonic event subsequent to their emplacement. The intrusions were injected during a brittle stage of deformation related to the F1 folding but prior to the development of the F2 folds and subsequent tearing and shearing by late brittle and brittle-ductile faults . The ultramafic and mafic rocks are intensely altered to serpentine, tremolite, actinolite, carbonate, biotite, hematite and pyrite according to the nature of their proto/it h. In the vicinity of the MTZ, all lithologies exhibit mineral assemblages indicative of the upper greenschist or lower amphibolite facies of metamorphism.The structural evolution of the MTZ involved superimposed folding, shearing, transposition, mylonitization, brittle and brittle-ductile faulting. Each lenticular motif results from the combined effect of conjugate sets of shear zones that outline lozenge-shaped blocks where strain markers indicate different strain states from cores to margins. Bedding in ultramafic flows and/or sedimentary rocks is either NW-SE or NE-SW within the blocks but, in the vicinity of the Malartie and S laden faults, it has been rotated to become subparallel to the faults.Ore shoots are most commonly associated with altered and deformed bodies of diorite and monzonite, or some mafic and ultramafic schists and, at the Canadian Malartic, Sladen and East Malartic mines, with metasedimentary rocks. The shoots occur in close proximity to the various faults of the MTZ but the gold itself is intimately associated with pyrite, biotite and carbonate in halos bordering fractures crisscrossing the different host rocks. The density of fractures and the width of their altered zones have been significant parameters in the production of economic ore shoots. Grains of gold are visible in some veins of quartz a"

Jan 1, 1990

By D. C. Treilhard

After a brief history of the mining and smelting operations of Kilembe Mines Limited, this paper outlines the smelter layout and describes . the. daily operations at the Jinja plant. Particular attention 1s paid to the details of the furnace and converter operation. A subsequent section of the paper deals with the significant developments in plant metallurgical practice, covering both smelting and converting.

Jan 1, 1966

By H. Wotruba, L. von Ketelhodt, M. Kowalcyk, C. Kleine, M. Robben

Sensor-based sorting is a financially and technically viable technique that is operating with little or no water and relatively little power consumption. Sensor-based sorting has already proven its operational stability at two gold applications in South Africa. Sensor-based sorting cannot only turn waste dumps and diluted mining blocks into reserves. The implementation can also cause a decrease in specific operating costs of mill and mine when for example replacing selective mining by bulk mining methods with subsequent sorting. Successful installations, operational experience, test work data and flow sheet integration from mine-to-mill underline the impact and potential that sensor-based sorting can have on the gold mining and processing industry.

Jan 1, 2011

By Arthur Notman

In view of the alarm expressed in many quarters over the increased production of copper to come from Canada and Africa in the future, it is of interest to study the history of the principal producing districts of the world and to attempt to forecast the future part to be played by them. Tables 1 and 2 record the world production and that of the United States, together with their respective rates of increase, both in percentage and actual amounts. The important point in this record is the decline in rates of increase for both the world and the United States, but more particularly in that of the latter, since 1881. The increase for the United States in the last decade is less than that for any decade since 1881, and is only 20 per cent of that for the decade 1911-20. The increase for the world is less than that for the two preceding decades, and is only about 65 per cent of the war decade 1911-20. Referring to Table 1, the decade 1871to1880 showed an increase of 32.l per cent in the world's production, which was the low until the last decade, ending 1930, which shows an increase of only 24.5 per cent. These decades both represent periods of economic stress following wars. In the first case the recovery was very sharp, the percentage increase in 1881-90 reaching a high of 86.4 per cent. It would seem dangerous, however, to assume that a similar high will be reached in the next ten years, because of the severity of the depression brought about by the Great War and the probability of its influence extending well into the next decade.

Jan 1, 1931

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

By P. Tukkaraja, K. Katzenstein

"Block caving is one of the most economical and efficient underground mining methods and has gained popularity around the world especially for extracting low grade and massive ore bodies. However, during the extraction of ore from the draw bells, gases trapped inside the cave could emit into the working areas; hence, ventilation plays a key role in operating block cave mines successfully where gas emission is a concern. To design an effective ventilation system for a block caving mine, given the dynamic nature of the caving process, it is necessary to develop airflow characteristic curves (P-Q) for a given cave. This study uses a 1:100 scale physical model with an exhaust fan system, and a Computational Fluid Dynamics model of a block cave to investigate the airflow behavior through the cave filled with broken rock material. From this study, it was observed that the cave airflow resistance increases with the decrease in cave porosity and the particle size.INTRODUCTIONThe block cave mining method is gaining popularity owing to its low cost and high productivity. This study considered a case where this bulk mining method is used for the extraction of an orebody that contains uranium mineralization. During the extraction of broken ore from the draw bells, radioactive gases trapped in the cave zone could be released into the production drifts and could create unsafe working conditions in the mine. Mine ventilation systems play an important role in regulating the migration of radon in working areas. One of the strategies to control radon migration in a block cave mine is to exert negative pressure on the cave zone by using an exhaust fan above the cave zone. In order to select an appropriate exhaust fan system, it is necessary to study the airflow resistance of the cave zone (Loring & Nelson, 2006).Extraction of broken ore via drawpoints creates a void volume inside the cave called the air gap. Air gaps with larger heights can lead to air blasts in a block cave mine should the cave collapse. Besides that, the air gap can also lead to decrease in ventilation system efficiency due to recirculation of air flow and associated shock losses. Air gap height can also have a profound effect on the variation of cave airflow resistance (Erogul et al., 2015, 2017). The knowledge of cave airflow resistance is also important for predicting the intensity of an air blast. Cave airflow resistance is a function of cave properties such as broken rock size, air gap, and porosity inside the cave zone (Baysal et al., 2017). Initially, a scaled experimental model with a forcing system was developed to investigate the airflow behavior through the cave, however, this model couldn’t provide an observable change in the airflow resistance when the cave properties were changed (cave porosity, and airgap) This was attributed to the difficulties associated with forcing system in terms of achieving lower porosity values with the available material (lightweight shipping boxes) for simulating broken rock inside the cave zones, and controlling air leakage from the model (Ajitha et al., 2018)."

Jan 1, 2019

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013