Search Documents

By M. E. Charles

The use of water flowing as a lower layer to reduce pressure gradients in petroleum pipelines was investigated using 17.5 deg. A.P.I. Lloydminster crude oil in a 1-inch laboratory pipe-line and a 21h-inch field pipeline. The method was found to be very effective in reducing the pressure gradient below that for the oil flowing alone. The factor by which the pres-sure gradient was reduced varied with the percentage of water added, and in general exceeded 10 for water contents ranging from 40 to 60 per cent. Within this range of water content the pressure gradient reduction factor was independent of the oil flow rate.

Jan 1, 1960

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By T. Sugawara, S. Hara, Y. Mitsui

Surfaces of rock slopes in cold regions often become frozen in winter. Therefore, understanding time-dependent behavior of frozen rock, as well as that of unfrozen rock, is important for long-term stability assessment of rock slopes. In this study, a series of uniaxial compression tests and creep tests were carried out on Shikotsu welded tuff under dry and water-saturated conditions at -20 °C to clarify timedependent strength and deformation of the frozen rock. The influence of water content on them also was investigated. It was found that the amount of deformation of the water-saturated specimen was much greater than that of the dry specimen. It also was found that the creep behavior of the water-saturated specimen was similar to that of polycrystalline ice. These show that deformation of the water-saturated specimen is strongly affected by pore ice. The UCS of the water-saturated specimen was approximately equal to that of the dry specimen at a strain rate below 4.2×10-6/s, and its value was about 17 MPa. However, the former increased up to 26 MPa at 4.2×10-4/s with loading rate, whereas there was little increase in the latter. This means that the UCS of the water-saturated specimen was always greater than that of the dry specimen at higher strain rates. The creep life of water-saturated specimens was longer than that of the dry specimens at stress level greater than 15 MPa. These results of UCS and creep life show that inclusion effect due to presence of pore ice plays an important role on strength of the water-saturated specimen. Creep life of the non-failure specimen that was loaded for more than three days was estimated by the relationship between creep life and axial strain rate at 10 s on failure specimens. It was found that creep life of the water-saturated specimens was shorter than that of the dry specimen at stress levels less than 14 MPa. This suggests that estimation of creep life of frozen rock under water-saturated condition is important for the stability assessment of frozen rock slopes. It was clear that the loading-rate dependency of UCS was related to the stress-level dependency of creep life in both dry and wet conditions. This indicates that there are common fracture mechanism in creep and uniaxial compression tests. It also indicates that the creep life can be estimated by the relationship between the UCS and the loading rate. The time dependencies of the water-saturated specimen were in good agreement with those of polycrystalline ice. This confirms that pore ice strongly affects the strength of the water-saturated specimens as, well as the deformation behavior.

Jan 1, 2015

By Pascal Lesagel

Life Cycle Assessment (LCA) is a holistic environmental assessment tool that allows the compilation and evaluation of the inputs, outputs, and potential environmental impacts of a product or service throughout its life cycle, from cradle to grave (i.e., from resource extraction and transformation to final disposal, including production and use stages). The relevance of LCA for the mining industry is twofold. First, the mining industry has a role in providing the LCA community the data that allows subsequent evaluations of the life cycle environmental impacts of primary materials such as metals, as well as the environmental comparison of the downstream products of the mining industry with other competing materials for specific uses. Second, the mining industry can use LCA in order to evaluate the environmental impacts of its activities, identify their environmental hotspots and compare the impacts of available technical options. For example, the environmental impacts of different extractive and processing technology can be compared through the use of LCA. This latter use of LCA by the mining industry is less common. This paper discusses the use of LCA to compare sulphidic tailings management options. The paper also presents some of the LCA research challenges that still have to be addressed to increase the relevance of LCA results for the specific context of mining activities.

Nov 1, 2008

By J. E. Hawley

"IntroductionA STUDY of the trace elements in the ash •of coals from nine seams in the Sydney coalfield, Nova Scotia, was undertaken at the suggestion of Dr. W. A. Bell, Geological Survey of Canada, as a part of a larger study of these and other Nova Scotia coals being made by the Geological Survey and the Nova Scotia Department of Mines under the direction of Dr. P. A. Hacquebard.The main purpose of this investigation has been to •determine if a knowledge of the trace element distribution might be of assistance in the recognition of individual seams, the distinction of which is not always easy or positive in folded and faulted strata by ordinary stratigraphic and structural means.The study has been so conducted as to afford information on the variation of trace elements in individual petrographic intervals or divisions in each of the seams examined, intervals determined by Dr. Hacquebard on the basis of their banded ingredients, vitrain, clarain, durain, fusain, etc, as observed under the microscope in polished sections. The results, as well, indicate the trace element composition of the coals of the area as a whole, and quantitative data for fifteen elements are given, along with concentrations of thirteen other elements, stated in terms of intensity ratios. Data on distribution of germanium, though considered here along with other elements, are dealt with elsewhere*."

Jan 1, 1955

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

By J. R. Donald, K. Scholey

"Nickel has been mined and processed from the Sudbury basin for over 100 years. During this period, the process has evolved into what is one of the largest and most complex mining and metallurgical facilities in the world. This paper will describe the geology and mining of the Sudbury basin as well as the Copper Cliff metallurgical flowsheet circa 2005, including:•,Clarabelle Mill,•,The flash smelting furnaces,•,The bulk converters,•,Matte casting, separation, and processing•,The carbonyl refineries•,Carbonyl residue processing•,Copper processing•,Sulphur productsThe challenges of today and the opportunities for the future are discussed."

Jan 1, 2005

By R. Krentz, P. D. Cordingley

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Major changes to the refining process were required when the Moa sulphide feed, with its unusually high cobalt content, was introduced in the early 1990's. In the period 1994 to 2005 the production capacity of the refinery has increased dramatically to match increases at Moa, and significant process improvements incorporated. The process flowsheet consists of the original ammonia leach process, optimized for cobalt chemistry and overall leaching capacity. Extraction of metal values is followed by the unique nickel-cobalt separation technology, in which most of the cobalt is separated from the ammoniacal nickel sulphate leach solution by precipitation as a nickel-cobalt hexammine salt. This salt is refined from a Co:Ni ratio of 1:1 to over 10,000:1 by selectively leaching nickel, redissolution and recrystallization in ammonium sulphate solution. Nickel and cobalt are recovered using the well-known Sherritt hydrogen reduction technology. This paper reviews the chemistry described above, examines some of the changes in operating conditions made over the years and highlights some of the recent physical changes made to the refinery.

Jan 1, 2005

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By S M. Roscoe

Relationships of Noranda sulphide deposits to volcanic rocks are reviewed and chemical variations within the volcanic sequence are described. The assemblages of minor elements in the pyrites and pyrrhotites of the Noranda and l\llatagami deposits are similar and are characterized by a high content of cobalt, tin and other elements. Isotopic compositions of lead, other geochronological data and stratigraphically disposed zonal distributions of sulphides and minor elements indicate that the deposits were formed prior to folding and metamorphism. Lead isotope data indicate that the Matagami deposits, and several others, were probably formed about 2.95 x 109 years ago and that the Noranda deposits may be about 50 million years younger. The volcanic sequence at Noranda is younger than the thick sequences bordering it on the east and on the west. The relationships are consistent with the hypothesis that these strata-bound sul1>hide de-posits are coeval with their associated volcanic rocks. T HE writer has been engaged in a metallogenic study of the region between Sault Ste. Marie and Chibougamau. An essential objective of this study is the classification of mineral deposits with regard to their composition, form, geological

Jan 1, 1965

By J. Ambrose, R. W. Zimmerman

"Shales are highly anisotropic in their mechanical behavior. The strength ( ??1) of anisotropic shales depends not only on the magnitude of the other two principal stresses ( ??2, ??3), but also on the bedding plane orientations (?) relative to the principal stresses. In this study, the role of the intermediate stress ( ??2) on the strength of shale is evaluated using new data from triaxial compression and extension tests. To understand the failure behavior of shales, we have carried out triaxial compression tests ( ??1 > ??2 = ??3) on two organic rich mudstones, at different confining stresses and loading angles. We first fit the triaxial compression data with Jaeger’s plane-of-weakness model, and find that the model is able to represent the strength behavior of anisotropic shales reasonably well. We then carried out five triaxial extension tests ( ??1 = ??2 > ??3) for a high strength-anisotropy shale, and two extension tests for a low strength-anisotropy shale. Results from the compression and extension tests for failure along the weak plane shows that the role of ??2 is not significant for weak plane failure. However, for the low strength-anisotropy shale, the failure strength of the intact rock (i.e., at ??= 0o and 90o) for compression and extension tests were significantly different. This indicates that for intact rock failure, the role of ??2 is important and cannot be ignored.INTRODUCTIONFor many years, various researchers have studied the roles of ??2 for failure of isotropic rocks. (Mogi, 1967 and 2007; Colmenares and Zoback, 2002; Al-Ajmi and Zimmerman, 2005 and 2006; Haimson, 2009; Ma and Haimson, 2012). The findings from these studies show that the effect of ??2 on the strength of isotropic rocks is generally significant, and cannot be ignored.Since the role of ??2 in the failure of isotropic rocks was recognized, other researchers attempted to extend some of these isotropic failure criteria to anisotropic rocks, but with limited success (e.g., Tiwari & Rao, 2007; Singh et al., 1998; Zhang and Zhu, 2007; Pei, 2008). Smith and Cheatham (1980), on the other hand, conducted true-triaxial experiments on the Green River Shale and used a J2-I1 type relationship to predict the strength behavior, but without considering the effect of the three-dimensional orientation of the weak plane on strength. Therefore, unlike for the case of isotropic rocks, additional studies need to be done to determine the role of 2 on the failure of anisotropic rocks."

Jan 1, 2015

By B. A. Zaharov, J. M. Shneerson, L. V. Chugaev, M. T. Zhunusov, A. M. Markelov, S. V. Drozdov

The main direction of research was the application of autoclave technology for the flotation concentrates or biooxidation feedstocks. The industry modernization also expects the possibility of increasing the yield of the flotation concentrate, to allow an increase in gold extraction in flotation circuit. This paper provides brief description of results obtained for concentrates with the yield of 4 and 8%, as well as corresponding biooxidation feedstocks. Technological efficiency of autoclave oxidation is shown for both concentrates and biooxidation feedstocks. The process has been evaluated on a laboratory and a continuous pilot plant scale. Gold extractions from POX discharge are ranging from 94-97% for each product, with only 5-7 kg/t cyanide consumed.

Jan 1, 2014

By Ann Bigué

Outline of Presentation 1. Impacts and Benefits Agreements Defined 2. Elements that determine the content of an IBA: ? the nature of the project ? the identity of Aboriginal communities affected by the project ? the legal environment 3. Content of Impacts and Benefits Agreements Impacts and Benefits Agreements Defined Have emerged in response to effects of major mining projects located on or close to Aboriginal lands and close to Aboriginal communities Are negotiated between the mining project proponent and one or more Aboriginal groups May include government May be known under other names

May 1, 2004

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977