Search Documents

By M. Tadayonsaidi

The effect of alloying elements on the mechanical properties and thermal expansion of 336 casting alloy usually used as piston alloy which has low thermal expansion and very good high-temperature mechanical properties and good wear resistance was investigated. The mechanical properties and thermal expansion characteristic of samples with different combination of alloying elements, which enhance to reduce the cost of products, have been studies, The results show remarkable increase in the mechanical properties with increasing the amount of Cu and Mg, while are reduced with increasing amount of Ni, On the other hand, the use of eutectic aluminum alloy as 336 alloy with higher percent of Cu and Mg and lower percent of Ni are recommended for industry, due to economical viewpoint and satisfactory properties.

Jan 1, 2005

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

By Robert D. Brown

"The Conservative Government 's budget proposals brought forward on December 11, 1979 have been withdrawn, but they are far from dead. On the contrary, a number of those budget proposals, especially the ones which would close loopholes and result in other technical changes being made to the Income Tax Act, should be considered to be alive and well.It is not unreasonable to expect the next government, of whatever political persuasion, to reintroduce many of these technical changes in the next federal budget. For that reason, last December's budget may have offered an interesting preview of what the mining industry and other taxpayers can expect in 1980. It is quite possible that some of these changes may be effective as of the original dates announced in the withdrawn budget proposals.This month, ""Tax Notes"" reviews the main pro visions of Mr. Crosbie's December, 1979 budget, with a primary focus on the changes that would have affected the resource sector.It must be emphasized that all of the budget proposals discussed herein have been withdrawn, that none of them are law and that any actual changes in our tax rules will have to be dealt with by the new Parliament that will be assembled following the February 18 election. December 1979budget withdrawnThe federal budget proposals brought forward by Finance Minister John Crosbie on December II, 1979 were withdrawn as a result of the defeat of the Conservative Government on a motion of non-confidence in the House of Commons on December 13. However, it appears quite possible that at least some of the proposals may be introduced into Parliament at a future date, possibly with retroactive effect.In a press release issued by the Department of Finance, Finance Minister John Crosbie stated that if the Conservative Government is returned to power, it will reintroduce all of the measures contained in his December II budget.Mr. Crosbie stated that all of the income tax measures contained in the budget would be reintroduced, effective on the dates indicated in the Notice of Ways and Means Motion tabled on December II. Some of the more important measures in December II budget, and their effective dates as indicated in the Notice of Ways and Means Motion, are discussed below.The December budget had also introduced or increased excise taxes or duties on gasoline, wines, cosmetics and photofinishing. If the Conservative party is re-elected, these measures will be reintroduced with prospective effect (i.e . effective as of new dates to be announced in the new budget)."

Jan 1, 1980

By Makhlouf Boubahziz

The HNIA field is part of the Tinrhert project which consists of developing 17 fields containing essentially gas with a few small rings of oil. It is considered as one of the main fields in this project in terms of its area and the number of geological structures that has formed it. It is a wide anticline of Cambro-Ordovician age, orientated NNE-SSW and located in the South-eastern part of Illizi basin. This structure extends from Alrar-center in the North, to the North of In Amenas in the South. The area is 1350 km2. The main reservoirs forming HNIA field are the Devonian (F2, F3 and F4), Siluro-Devonian (F6) and Cambro-Ordovician. These latest are formed by 4 sandy units alternated by layers of shale and shaly silt termed from the base to the top as follow: Unit II, Unit III-3U, Unit IV-2L and Unit IV3; these units are the subject of this study. The HNIA field is essentially gas, up to day this field is at the stage of appraisal and evaluation in order to establish a development plan; therefore the main target of this study is to contribute to this frame work. The following objectives are: ?To build a structural model of the study area. ?To integrate all the sedimentological, structural and petrophysical data in order to build a 3D geological model

Aug 1, 2013

By Joanna LaForte

"IntroductionIn respect to The Human Dimension by M. Phyllis Bray, this author's impression is that research on long distance commuting (LDC) is long overdue. This type of mining is not new to many workers, especially those from areas such as the Maritimes, who have had to look for work away from their families for at least a decade. Perhaps to the industry the over-all set-up is new, but to workers who have faced mine shut-downs in their areas finding a job was the main objective and if the security of long-term employment was evident, then the families might join them later. This was the situation with which the writer' s family was faced.LDC LifestyleBeing the wife of an underground miner, the author has personally experienced this lifestyle for almost 10 years, and has never experienced accommodation in a company town. The first five years of marriage were spent in a small rural municipality within 50 miles of the worksite, but the town had industry separate from mining and was not affected by the mine shut-down.Since her LDC lifestyle began her family has been pretty much city-based, out-of-province commuters with two children and a third to arrive some years later. She therefore lived a fairly normal married life with a husband home daily. The author has experienced life with a husband who worked away for five-day stretches and then drove long distances to be home weekends or the portion of time left over from driving and fatigue. She has done the 3D-days in/l4-days out routine, and for approximately the past four years has been existing on a two-weeks in/two-weeks out ritual .The author does not agree that the ""bottom line is that mining families go where the jobs are"" . The miners go where the jobs are and the families fend for themselves with the assistance of the pay cheque making it home each pay period.Perhaps because there are many personal frustrations with this type of lifestyle, perceptions may be inaccurate. Having only dealt with underground operations, there may be gross differences between the pressures and demands of other forms of mining."

Jan 1, 1991

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By A. Grimod

The European Guideline ETAG 027 - 2008 (?Guideline for European Technical Approval of Falling Rock Protection Kits?) defines the procedures to test rock fall barriers. Nowadays, this guideline is essentially the only test and construction framework utilized by manufacturers and it is also starting to enter in the mentality of designer who can clearly specify the performances of rockfall barriers. ETAG 27 (and the related European Technical Approval and the CE marking) represents a milestone for the rockfall barrier market, because it gives the possibility to compare the performances of different fences and it ensures the quality of the certified product. For these reasons ETAG 27 presently constitutes the base for tenders all around the world. Although rockfall barriers are in common use, designers and consultants do not have a clear overview of the real performances and the technological limits of these structures. The first problem can be solved using ETAG 27 criteria, which allow designing rockfall barriers at ultimate and serviceability limit state. Even though ETAG 27 uses crash tests performed with the Service Energy Level (SEL) and Maximum Energy Level (MEL), design with these concepts is not obvious or in common acceptance. Some preliminary questions must be solved. When can these energy levels be correctly applied? In the case of rockfall simulations, what probabilistic approach must be used for the evaluation of the barrier? Unfortunately ETAG 27 does not give any information or tests relating to the technological limits of the fences. Therefore some important questions arise. How do the site specific aspects of installation affect the barrier performance? What is the behaviour of the barriers under extreme conditions? And finally, the main question lies in the background: what is the functional reliability of ETAG 27? All of the above questions require comprehensive answers, which is consistent with the experience of designers, installers and producers. Officine Maccaferri S.p.A., with its 130 year experience in the field of rockfall protection, collected a large number of case histories with barriers impacted by single or multiple blocks, debris flows, and snow avalanches. Throughout these case histories and in accordance with a recent Italian standard code, it has been possible to implement a reasonable design approach that considers the efficiency of the barrier, the uncertainties of the input data, and the fore

Aug 1, 2013

By T. W. Wlodek

Abstract A simplified method of fatigue testing full-dimension, as-rolled, non-machined, mining drill rods is very desirable to the mining and steel industries in the classification of steels available on the market, through the evaluation of their fatigue limits and endurance strength. In this paper one such simplified method is presented and analysed. The preliminary results show many advantages of this method, such as simplicity and constancy of loading. The type of loading applied more or less simulates the working conditions of the outside fibres of the mining drill rods. Additional advantages of this method are the possibility of testing under dry and wet conditions, its quietness, and its ease of operation. Specially designed adaptors and specially applied techniques of fixing and preparation of samples make possible the breaking of a quarter-octagon hollow drill rod in a free length of uniform section in a rotating beam machine. At first glance this seems to be difficult to achieve. In the first preliminary test three different lots of steel were used. S-N curves under dry conditions were determined. These curves permit of the classification of the drill rods on the basis of the fatigue limit and endurance strength of the outside fibres of the metal, which is dependent to a greater or lesser extent on the effect of surface decarburization, surface imperfections, and special surface treatments. The average slope of the S.N curve in the damaging zone, and the fatigue limit in equal tension-compression rotating bending, were determined for SAE 1080, chromium-molybdenum and nickel-chromium-molybdenum mining drill rods. INTRODUCTION The fatigue limit and the endurance strength of mining drill rod steels are of interest to both the mining and the steel industries. These industries are greatly interested in lowering the cost of mining by reducing the consumption of these steels per ton of ore exploited.

Jan 1, 1951

In this paper we present the results of preliminary investigations into the applicability of new laboratory scale tests for the prediction of operating gap and specific throughput in high pressure grinding rolls (HPGR). The work is a part of the CAMIRO HPGR research program being conducted at the University of British Columbia, which aims to develop a suite of small-scale tests and procedures for the selection and sizing of HPGRs. A focus of the presented study is to test sample types in terms of their terra-mechanics based characteristics and relate them to specific throughput and gap results from pilot HPGR testing on the same samples.

Jan 1, 2012

By I. Cotman

Dimensional stone processing has become an important part of the world extractive industry, and today?s total stone block yearly production is estimated to be around 134.000.000 tons and is still growing by an average yearly rate of approximately 20%. In future, the same production will become an important part of the mining industry and presently, in some countries it represents even the main mining output. New environmental regulations, together with landscape and nature conservation requirements, create a number of difficulties in setting up new open pit dimensional stone quarries. As a result, many dimensional stone producers have recently started to apply underground techniques in order to produce the ornamental stone blocks intended for further processing. Underground production of stone blocks requires special mining methods and so far it has not been a cost-effective excavation method for all types of rocks. Presently, this type of stone excavation is generally applied in sedimentary and marble deposits because the rock has small to no mineral quartz content. When starting a new underground dimensional stone mine, it is necessary to analyse the impact of all primary factors which are crucial to set up a technically and cost effective advanced underground dimensional stone mine. The role of physical and mechanical properties of the rock, geological conditions, mineralogical composition, micro-tectonic state of the site, rock mechanic conditions on the site, durability and saw ability of the stone are decisive factors in foreseeing the future methods of extraction. The laboratory research work as well as the field work, is very important in decision-making aimed to choose the future excavation method. Also of equal importance is the serious market research, because it renders the indication of selling price potential. Having obtained the results from both types of research, mining engineers can design the mining methods which optimize financial return to the mine. The practice approved by 15 years of testing in the underground limestone quarry of Kanfanar gives future producers very useful advice and general data to facilitate the process of exploration intended to establish new similar underground quarries.

Aug 1, 2013

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By D. S. Speakman

The copper-zinc orebody at Sherritt Gordon's Ruttan Mine occurs in a structurally complex area of the Rusty Lake greenstone belt in northern Manitoba. Problems in interpreting drill results indicated a large deviation, and the structural complexity an erratic deviation, of drill holes. This was confirmed when a surface hole was intersected 420 feet to the left of line on the 800 level. This problem acted as a catalyst in promoting a search for a suitable down-hole survey method. The instruments investigated included magnetic multishot and gyroscopic units as well as the ABEM Reflex-Fotobor. Only the Fotobor came close to meeting the company's needs of simplicity, reliability, accuracy and ownership. In this paper, the methods of operating this instrument, as well as the data extraction and reduction techniques, are described. Data on the accuracy and repeatability of the instrument are presented, and a tabular presentation of the results of surveying on 86 holes totalling 64,000 feet of drilling is made. Preliminary statements of the results of ongoing research on causes of hole deviation are presented and recommendations for minimizing deviation are given. The use of the survey device is recommended in areas of structural complexity, for very steep or backsight holes and where expected ore intersections are missing.

Jan 1, 1978

By P. C. Thurston, T. Setterfield, D. H. Watkinson

"The Maybrun copper deposit IS In a succession of pillowed basaltic flows in the Wabigoon sub-province, northwestern Ontario. The rocks have primary flow morphologies and remarkably well-preserved crystallization textures, including quench-textured plagioclase, in spite of metamorphism to the amphibolite facies. The sulphide assemblage chalcopyrite-pyrrhotite-cubanite with minor sphalerite and pyrite is primarily in interpillow spaces and is stratabound. Basaltic rocks immediately enclosing the copper sulphide minerals have an enrichment in Fe, Mg and K and depletion in Ca and Na relative to surrounding flows. The Maybrun deposit is interpreted to have formed contemporaneously with volcanism and alteration, and was subsequently metamorphosed with the enclosing basalts.IntroductionThe association o f significant base metal accumulations with mafic submarine flows in the Archean is as yet poorly documented. Such deposits, where noted, have typically been small, and are therefore commonly over looked. The Maybrun Mine, a 2.6 x 106-tonne copper deposit in pillowed basalt, has many similarities with large, well-documented volcanogenic deposits. Given the interpretation of the Maybrun Mine to be volcanogenic in origin, there is n o reason why similar processes could not produce large deposit s. This is an important realization in an area where Archean submarine mafic rock s are very common, but frequently are examined only superficially. As gold commonly occurs in deposits such as Maybrun, even modest-sized deposits may be economic. The basalts at Maybrun are remarkable for amphibolite-facies rocks because of their extremely well-preserved delicate volcanic textures, including quench textures.The Maybrun Mine is one kilometre south of Atikwa Lake, in the Wabigoon sub-province of the Superior structural province, 75 km southeast of Kenora, northwestern Ontario, at longitude 93°35'W, latitude 49°25'N (Davies, 1973). Archean metavolcanic and metasedimentary rocks and intrusions underlie the area. Goodwin (1970) concluded that the mafic and minor felsic metavolcanic rocks, as well as the overlying metasedimentary rock s, were an eastward extension of the lower cycle of the Keewatin type section for the Lake of the Woods area. He estimated that the stratigraphic thickness of Keewatin rock s in this area is about 6900 m, of which 87% is basalt. The flows contain numerous interlayered sills, predominantly of basaltic composition; they have been extensively folded, faulted, metamorphosed to amphibolite facies and intruded by numerous felsic bodies, most importantly the Atikwa Batholith."

Jan 1, 1983

By Yan Germain, Université Laval, Bernard Dallaire, Jocelyn Bouchard, Peter Radziszewski, Gilles LeBlanc, Michelle Levesque, Nicolas Tremblay

"The comminution process is estimated to be only 1% efficient, resulting in waste energy dissipated as heat, noise, and vibration. Energy recovery from grinding circuits has not been implemented mainly because recovering heat from the surface of the grinding mill or from mill slurry can impede operation, increase maintenance requirements, and prolong plant shutdown time (and production). However, currently very little information is available in the public domain regarding the amount of waste energy and that potentially recoverable in the grinding circuit of a mineral processing plant. Availability of such information could drive innovation and improve decision-making regarding opportunities for waste energy recovery. The Canadian Mining Innovation Council (CMIC) has initiated a study with CanmetMINING and mining industry partners to develop a model to map the energy flows in grinding circuits and to quantify the potential for energy recovery. The paper outlines the underlying fundamentals and data requirements for use in the model and then focuses on quantifying the energy recovery potential of the semi-autogenous grinding and ball mill circuits at the Agnico Eagle Goldex Division. Results show that most of the electrical energy (over 75%) is used to heat the slurry, leaving only a relatively small amount of it to achieve mechanical work (~9%). INTRODUCTIONCanmetMINING commissioned a study in 2013 to better understand the barriers for adoption of new technologies in the mining industry (MNP, 2013). The conclusions highlighted the importance of enhancing industry/regulator engagement and communication to raise awareness and improve the industry’s comfort level with new technologies.In November 2014, the Green Mining Innovation Advisory Committee (GMIAC) held a workshop to explore the possibility of accelerating the uptake of green mining technologies by bringing together key stakeholders among the mining value chain to address industry priorities. Participants included representatives from mining companies and associations, academia, provincial governments and federal departments and organizations. Two key priority areas emerged at the workshop: i) energy saving, and ii) water management."

Jan 1, 2016

By Peter A. Hacquebard

"The coals of the Sydney and Pictou coalfields are generally classed as high volatile ""A "" and medium volatile bituminous coals but there are significant differences within and even beyond this rank. These are related to the observation that the coalification in eastern Canada is essentially post-deformational, resulting in a general increase of rank with depth in individual seams.Exploration drilling in the Sydney coalfield has shown that the rank increases offshore to M. V. bituminous at mineable depths and in the Pictou field to L. V. bituminous coal. There is also a marked easterly shift in rank within one seam at the same depth at Sydney, with the result that M. V. coal will be reached sooner in the Donkin Reserve area (at 700 m depth) than in the Lingan-No , 26 Reserve area (at 900 m depth). These rank changes are important for the manufacturing of metallurgical coke as shown with coke stability predictions based on petrographic analyses. The L. V. coal of the Pictou field can be used for blending purposes and is the only known L. V. deposit of mineable thickness in eastern Canada.In addition, the vertical rank changes between seams have been studied in ten boreholes. They are not constant within the confines of the Sydney coalfield. Four separate areas can be recognized, each with different coalification gradients, which can be related to changes in the paleogeothermal gradients . Variations of 2.5 degrees to 6. 7 degrees CI IOO m are indicated and geological causes for these changes are suggested.IntroductionThe Sydney coalfield is the largest and most important field in eastern Can ad a, and although it has been in production some 200 years, the remaining ""demonstrated "" resources of 1.6 billion metric tons can extend its production capability for at least another 100 years. All coals mined are high volatile "" A"" bituminous and have been used for both thermal and metallurgical purposes. For the latter rank variations even of a minor scale are of critical importance for the manufacturing of metallurgical coke.The significance at the present time of the Pictou coalfield, which has only modest remaining "" demonstrated"" resources of 60 million metric ton s, lies in the discovery in 1975 of a 14-million-ton deposit of low volatile bituminous coal. It is the only known low-volatile coal in eastern Canada and is suitable for use as a blend for metallurgical coal. As such, it could supply the Sydney coke ovens for a period of 30 years at the current rate o f coke production and replace imported American low volatile coal.Consequently, coal rank studies of the Sydney and Pictou fields are important not only from a geological point of view, but also because of economic considerations."

Jan 1, 1984

By W. A. Green

Introduction While pilot-mill operations were being carried on at Flin Flon, as described by R. E. Phelan (1), a detailed topographic map was being made of the area in the vicinity of the ore-body for later use in laying out plans for the final plant. The area covered by this survey was 6,600 feet by 6,600 feet, with contours on 2-foot intervals. As mentioned by Mr. Phelan, it was definitely decided at the end of November, 1927, to take up the option on the Flin Flon property and to proceed immediately with the plans for construction of a metallurgical plant at Flin Flon to treat 3,000 tons of ore per day, and of a hydro-electric power plant at Island Falls, Saskatchewan, to supply power for the future operations at Flin Flon. Railway Built From The Pas to Flin Flon Just as soon as the decision was made to go ahead with the construction work and opening-up of the property, it was of course essential to give immediate attention to the building of a railway to the mine. Many years previously, a preliminary survey had been made for a railway to branch off the Hudson Bay railway at a point 4.7 miles northeast of The Pas, and, during certain negotiations in 1925, the Provincial Government of Manitoba had agreed to guarantee the railway bonds necessary to finance the building of the line, so that it was possible to organize for this work immediately. A contract was let by the newly organized Manitoba Northern Railway Company to the Dominion Construction Company, Ltd., and Tomlinson, for the building of the railway to the mine, a distance of approximately 87 miles (see Figure 1). The Manitoba Northern railway is a subsidiary to the Canadian National railway, and all engineering and supervision of the contractors was done by the Canadian National engineers. Actual construction work was started in January, 1928. The first 52 miles of the railway from The Pas to Cranberry Portage is over fairly level, although slightly rolling, country, and a considerable portion of the route is over muskeg area. Rails were laid on top of the frozen muskegs. Gravel deposits were opened-up along the line and, before warm weather; sufficient ballast .was distributed in the muskeg areas to prevent thawing under the track, and thus give the necessary support to allow uninterrupted transportation over the line.

Jan 1, 1935

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926