Search Documents

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By R. Pandher, R. Schonewille, N. Tripathi

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGE TM METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By R. Pandher, R. Schonewille

Advanced process modelling tools were developed for the Xstrata Nickel Sudbury Smelter flow sheet using a combination of FACTSAGETH METSIMTM and ARENATM software. These tools were employed to assist with plant optimisation, emission control, process design, troubleshooting and case studies as applied to the smelter. The development of process modelling tools in pyro-metallurgy commonly involves an in-depth study of the therm o-chemical properties (heat capacity, liquidus temperature, etc.) of all high temperature phases, usually matte and slag. The preferred tool for this purpose is FACTSAGETM, a well-known then-no-chemical modelling software package. The results from the therm o-chemical model have been subsequently incorporated into the development of a process model for the entire smelting facility using the METSIMTM platform. Such process model also includes a number of special features adopted to effectively simulate the complex industrial phases; matte and slag systems. To ensure the robustness and reliability of the process model, several process parameters and assumptions were verified with laboratory and plant data. Consequently, the model includes the ability to examine the impact of a number of plant parameters on potential plant performance. Primary variables are the percent sulphur elimination during concentrate roasting, furnace matte grade and degree of matte metallization. Key output parameters include operating temperature, furnace coke requirement, sulphuric acid production, CO2 emissions and overall energy requirements. Selected outputs from the process model (for example blowing time, slag production rate and matte converting rate) can then be utilised in the development of a discrete event model (DEM) for the smelter using ARENATM software. Incorporation of reliable and validated mass balance parameters enhances the robustness and reliability of the DEM model. The integration of then-no-chemical, process and DEM modeling tools has a distinct advantage in planning plant trials and examining process design initiatives at Xstrata Nickel's Sudbury Smelter. The present paper discusses the development of these three models and the synergies existing among them. Typical results from all three models are also presented.

Jan 1, 2011

By Frédéric Flament

The aim of this paper is to present the development of a data validation software as component of a commercial mass balance package. Data reconciliation through mass balance is basically an optimization problem constrained by the law of mass conservation. As any optimization problem solved with a modern and robust software application, erroneous information or starting point will always lead to a solution, whether it is realistic or not. Moreover, good information wrongly weighted by an incorrect error model will lead to the same bad ending. In an industrial context where competition requires accurate information, data reconciliation without validation can be disastrous and calls for data validation before and after reconciliation. The challenge in automated data validation resides in the development of general theoretical solutions. Until now, none has been presented and only partial solutions are available. The development presented in this paper incorporates some of these partial solutions. The integration of human knowledge into the application paved the way to a more general solution. The combination ?theoretical validation ? human expertise? proved to be flexible and reliable enough to be integrated in a commercial data validation package. Numerous examples though industrial applications are presented. These applications demonstrate the validation of raw measurements, user support in the development of error models and validation of reconciled measurements.

May 1, 2001

By H P. Tardif

This paper briefly describes some of the phenomena encountered when materials are submitted to extremely high pressures, such as those produced by the detonation of an explosive charge placed in contact with the material. It was found that extensive changes take place in the? microstructure of iron and steel. Diffusion-controlled processes, such as the transformation of lamellar pearlite, the recrystallization and grain growth of ferrite, and the homogenization of the pearlite-ferrite structure, can take place within micro-or milliseconds. Mechanical twins can propagate without deviation from ferrite to pearlite, thus indicating a proeutectoid ferrite-pearlite-ferrite orientation relationship. The propagation and interaction of intense stress waves in materials was demonstrated with the use of Armco iron. Finally, a comparison is made of the damage produced in metals by the formation of craters made by explosive shock and by hypervelocity impact. D DRING the last few years, exceptional development has taken place in the field of explosive metallurgy, i.e., the

Jan 1, 1964

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By T. Bhambhani, Mukund Vasudevan, Partha Patra, D. R. Nagaraj, P. Somasundaram

Selective Ni separation from ultramafic ores rich in serpentines has been a huge challenge in the mineral processing industry, and therefore highly inefficient. Analysis of the root causes of the challenges and consequent development of robust processing solutions were the main goals of the Cytec-Columbia. University-Vale Joint Development Program. In this context, the subject of this paper is limited to one of the key findings of this research program which is the influence of fibrous serpentines on grade-recovery characteristics. Specifically, the poor flotation behavior is characterized by an atypical reverse C-shaped grade-recovery curve.

Jan 1, 2011

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By C. M. Díaz, P. J. Mackey, P. Coursol

In a recent paper [1], the present authors discussed calculated energy consumption numbers in copper sulphide concentrate smelting for four different smelting technologies. For the present study, from among these technologies, they selected the Noranda/Teniente continuous bath smelting followed by Peirce Smith (PS) converting route to investigate the impact on total energy requirement of some key process variations, such as tuyere injection of dry concentrate vs. slingering of wet concentrate over the molten bath, continuous converting vs. conventional batch PS converting and commercially proven slag cleaning alternatives. In their calculations, the authors used the same thermochemical model and methodology used in their earlier paper. This approach to explore plant design options provides an interesting basis for evaluating flowsheet modifications that could lead to significant copper smelting energy savings. The METSIM software was used in the present paper to carry out heat and mass balance computations for 8 different flowsheet configurations. The results are presented and discussed in the paper with respect to copper recoveries, energy requirements and CO2 emissions.

Jan 1, 2011

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By M. F. Goudge

THE present century has witnessed an amazing transformation in the uses of limestone. From being mainly a structural material, a role it has played since the beginning of civilization, it has become one of the in-dispensable raw materials for use in the great chemical and metallurgical industries that play such a vital part in the economic life of the nations today. Its uses have become so diversified and numerous that it enters, directly or indirectly, into nearly every phase of modern life. In this introductory paper it is proposed merely to outline the general usefulness of limestone and to point out some of its salient features, and to leave any detailed discussion of uses to the papers that follow. The term limestone as herein used embraces all kinds from the variety known as high-calcium limestone, which is composed almost entirely of calcite, to the dolomitic variety, composed largely or entirely of the mineral dolomite. Lime is simply calcined limestone and, in considering the uses of limestone, the uses of lime should also be included, particularly in view of the fact that, in many processes, it is possible to use limestone in either the raw or the calcined state.

Jan 1, 1939

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By K. Hardy

As part of Inco's $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco's Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco's new WATP.

Jan 1, 2006

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

The present work aims at some process modifications in specified metallurgical processes, wherein CO2 can be used successfully as an oxidant for decarburization in steelmaking and applied in some non-ferrous metals production processes. During the decarburization of Cr-containing high alloyed steels, the present researchers investigated the possible use of CO2 instead of Ar-O2 mixture and could successfully decarburize the steel melt without significant loss of alloyed Cr to the slag phase. A mathematical model was developed based on the bubble formation accompanying the chemical reaction: C(molten steel)+ CO2(gas)= 2 CO(gas). The model predictions were tested by laboratory scale (1 kg) experiments carried out in an induction furnace and very good agreement between the model predictions and experimental results were observed. A national project has been sanctioned in China for the implementation of CO2 in decarburization of ferroalloys as well enable the addition of pig iron in the electric arc furnace process when the scrap supply is limited. New processes have been developed for the utilization of CO2 in the case of non-ferrous processes. A novel method of treatment of Al dross by leaching with water and capturing the evolved NH3(formed by the hydrolysis of AlN) has shown very promising results.

Jan 1, 2015

By Jie Li, Xinyu Liu, Yan Chen, Linjian Ma, Yasong Wang

Nonlinear time-dependent response analysis of salt cavern under extreme loads in disaster mode is of great importance to the safety and disaster prevention of gas storage group. Uncontrolled blowout is one of the extreme conditions for compressed-air cavern operation. Based on the geological structure of Jintan salt deposit, China, the numerical model of the complete process of water solution, cyclic operation, and internal pressure runaway was developed. The effects of rapid unloading on the stress filed, the progressive failure of surrounding rock, the volume convergence of storage cavern, and the ground subsidence were simulated employing an elasto-viscoplastic damage constitutive equation for rock salt. The results indicate that the damage and failure zones propagate much larger in the mudstone interlayer than in the host salt. The volume of damage and failure zones surrounding salt cavern induced by unloading process is 5~6 times that of cyclic injection and withdrawal process. The average volume convergence rate of salt cavern reaches 0.012%/d~0.013%/d, which is 6~6.5 times that induced by cyclic operation. The ground subsidence exhibits a typical funnel curve. The affected region of ground subsidence due to rapid unloading in the blowout period is about two times the maximum cavern diameters. Furthermore, double cavern analysis reveals that the interaction between adjacent caverns may be ignored so long as the pillar width is larger than two times the maximum cavern diameters.

Jan 1, 2015