Search Documents

By S Grönstrand, C. Perez, A. B. Yañez, F. Coddou, P. Morales, H. Elgueta

"The TankCell® 300 forced air flotation cell designed and built by Outotec, with active volume of over 300 m3, was installed at Codelco’s Chuquicamata concentrator in September 2008. After that, a program was conducted, where the new cell was tested against the plant’s existing flotation cells of type TankCell® 160, with an active volume of over 160 cubic meters.Testing program was exhaustive and detailed. Grade-recovery curves for each setup were reported, along with recoveries by particle size. Secondly, operational characteristics like air feed and froth height setpoints, and power consumption are compared side-by-side. As the third topic, gas dispersion characterization included velocity mapping, holdup, bubble size and bubble surface area flux operating range. The fourth area of interest was the retention time distribution (RTD) of the 300 and 160 m3 cells in comparison. A detailed campaign using radioactive tracer tests was conducted to clarify this.All of the investigations mentioned above are reported in separate papers for more detail. The aim of this paper is to collect the key findings, and present them in real terms, always referring to operability and metallurgy of the cells. It is destined for people designing new plants and to those improving and expanding existing ones. The most frequently heard question is: will the new large cells operate at same efficiency as the smaller ones. In short, the answer is: NO. They operate at improved efficiency!INTRODUCTIONIn the last two decades of minerals processing, there have been three dominant trends of development in the flotation technology: equipment scale-up, cell characterization and circuit modeling. Equipment scale-up has been rapid in the past two decades. In the year 1990, the largest flotation cell in use was 50 cubic meters of size. This year, 300 cubic meters is the largest installed cell. Characterization of flotation equipment and circuits is a very popular subject nowadays and has helped many operations to improve their recoveries through better control strategies, for example by using optimized air feed and level control profiles (Gorain, 2005), (Doucet, Gomez, Finch, 2006), or through better maintenance (Coleman, Urtubia, Alexander, 2006). Characterization work is closely linked to circuit modeling. The aim is to produce sufficient amount of data to allow reliable model building. These models are then used to design new circuits and to improve existing ones. So in summary, these three lines of development have slightly different aims – from capital and operational cost to performance optimization. Ultimately, they converge in the same end result – maximizing the profitability of the operation. Following chapters will summarize the extensive test work and scientific studies at Codelco Chuquicamata. The aim was to compare a TankCell® 300 cell, with nominal volume of 300 m3, against two TankCell® 160 machines, with 160 m3 volume in each. The work should yield answers to questions: does the larger cell produce similar results – is the scale-up successful?"

Jan 1, 2010

By A. C. Hnatyshyn

INTRODUCTION THOSE concerned with coal mining operations in Alberta have been asked repeatedly the same question, "Why is mechanization in Alberta proceeding so slowly as to lag far behind the mines in the United States?" This question is often asked in such a manner as to indicate that a severe reprimand is overdue to the mining engineers of this Province for their apparent indifference to the problem of improving their mining operations by increased mechanization. To the average person, unacquainted with mining conditions and problems, mechanization appears to be simply a matter of introducing equipment to load coal underground and, once this is done, substantial economies in operating costs will automatically follow. Invariably, those who have followed this simple reasoning have found, to their regret, that such is not the case and that effective mechanization involves something more than the mere process of introducing loading equipment into a mine. To be effective, any programme of mechanization must take into consideration all operations incidental to the mining, transportation, and handling of the coal from the working face to the tipple, and must utilize equipment which can be best adapted to any peculiar condition or circumstance prevailing in the mine concerned. In the use of such equipment, the net and final result should be an improvement in operating costs of sufficient magnitude to at least return to the operator, over a specific period of years or during the expected life of that equipment, all his investment plus a fair return on that investment.

Jan 1, 1951

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By K. Parameswaran

This paper builds on presentations made at the Conference of Metallurgists (COM) 2015, COM 2017 and Extraction 2018 and associated papers published in the respective conference proceedings. Based on the classic Brundtland Commission definition of sustainable development as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper describes how metal mining can be compatible with sustainable development and how sustainability considerations have been applied in the primary copper industry, using several examples of sustainable mining practices from ASARCO LLC operations. Finally, the paper discusses how these considerations might be used in the future by discussing the need for developing a sustainable development strategy and how this strategy can be aligned with the United Nations Sustainable Development Goals. INTRODUCTION The primary copper industry comprises: mining (also referred to as “extraction”); mineral processing (also referred to as “beneficiation, “milling” or “concentration,”) which includes leaching, solvent extraction (SX), crushing, grinding, froth and flotation operations; and metallurgical processing which includes smelting and converting; refining, which includes fire-refining or anode refining and electro-refining; and electrowinning (EW). There are two routes for producing refined copper: hydrometallurgical and pyrometallurgical. The hydrometallurgical route comprises mining (open-pit and underground), mineral processing (crushing and grinding — for heap leaching only; leaching and SX) and metallurgical processing (EW). The pyrometallurgical route involves mining, mineral processing (crushing, grinding and froth flotation) and metallurgical processing (smelting, fire refining and electro- refining). The primary copper industry is capital, water, resource and energy intensive with the potential for significant environmental impacts, if the environmental aspects are not properly managed. ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V (Grupo México) acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, SX-EW plants, a copper smelter in Arizona and a copper electrolytic refinery in Texas.

Jan 1, 2019

By L. E. Djingheuzian

IN 1953, Lewis (1) published an article which brought forth a great amount of discussion by grinding engineers. In his contribution to discussion the present writer (2) suggested that, for the most efficient performance of a ball mill, there must be a .definite relationship between Cn, per cent critical speed, and V p, per cent mill volume occupied by the ball charge. Later, he ( 3) was able to publish some grinding data from Wright-Hargreaves milly which appeared to bear out this contention. It is with this view to establishing a fundamental relationship between Cn and Vp that the idea of this Forum was conceived. Accordingly, a questionnaire was prepared and copies of it were mailed to over eighty Canadian mill operators. This questionnaire did not include a question on dilution on the assumption that each mill operator was using the most efficient dilution for his operation, nor was a question on efficiency of classification included since it was thought that the inclusion of efficiency of dassification in the questionnaire at this preliminary stage might render the forum discussion,. while everybody was trying to find his bearings, too unwieldy. However, it is evident that, as discussions develop, this forum will have to define a uniform method for establishing most efficient classification in grinding circuits

Jan 1, 1957

By A. Saigal

A finite element analysis based investigation using DEFORM software was undertaken to model the extrusion of 15% alumina and 15% silicon carbide reinforced aluminum metal matrix composites. The study dealt with predicting the extrusion load as a function of ram displacement and initial billet temperature. The finite element simulation was also used to determine the maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions in the billet during the hot extrusion process. The constitutive equation used was of the type: Z = E exp(Q RT) = A{sinh(ao-)}" where Z is the Zener-Hollman parameter (temperature compensated strain rate), s is the strain rate, Q is the activation energy, R is the gas constant, T is the absolute temperature, a is the flow stress and A, a and n are constants. Based on the work of Davies et al and McQueen and Konopleva, the values of Q (KJ/mol), a (MPa-1), n and A for aluminum 6061 composites reinforced with 15% alumina and 15% silicon carbide used are 181, 0.024, 4.15 and 1.33x10'2 and 233, 0.052, 2.60 and 1.26xl0'4, respectively. Even though the individual parameters are quite different, it was found that the predicted maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions are quite similar and differ by no more than 1-2 percent between the two composites indicating that the deformation behavior is primarily controlled by the matrix material and is not a function of the type of reinforcing ceramic particulates.

Jan 1, 2004

By J. A. Brothers, M. R. Foran

"AbstractThis paper reviews the progress made in the manufacture of hydraulic cement from iron blast-furnace slag by simply grinding the granulated material with other constituents. The influence of the chemical and mineralogical composition of the slag, the conditions of granulation, the manner of drying, and the fineness of grinding, on the hydraulic properties of the cement, is discussed. The effect of additions of lime, portland cement, and anhydrite, alone and in combination, on the physical and cementing qualities of the mortar and concrete made from Sydney blast furnace slag, is shown in tables of data and is reviewed in some de- tail. The work at the Nova Scotia Technical College has shown that a cement equivalent in every respect to portland cement can be made from basic blast furnace slag- by the us2 of certain quantities of portland cement as an activator.IntroductionBlast furnace slag is a potentially valuable material for the manufacture of hydraulic cement. It is a by-product of the manufacture of iron in the blast furnace, and is formed by the combination of the silica and alumina .of the iron ore with the limestone flux. The metallurgist terms a slag .acid or •basic according as the percentage of lime is less or greater than the percentage of silica plus alumina. The basic slags have the •more pronounced hydraulic properties."

Jan 1, 1950

By A. Brown

"The first printed report on Canada's coal resources was published in Paris in 1672(1. Written by Nicholas Denys, then Governor for France of Isle Royale (Cape Breton Island), the report dealt exclusively with the coal of the Atlantic region because little or nothing was known about the interior of North America. Clearly, also, he wrote about a resource of which much was known among the military and early settlers of that day. This early knowledge is not surprising because the presence of coal is clearly displayed in the coastal cliffs of Cape Breton as it was also, at a later date, to the first arrivals on Vancouver Island.An example of early use was that of the French garrison at Fort Louisburg in the first half of the 1700s. Still earlier, in 1643, Governor Winthrop of New England reported the receipt of a small ship load of coal from New Brunswick (2). Despite this early knowledge there was no significant development of coal mines until the 1800s. This had to await the ending of wars between the French and British factions and the growth of population. Basically, also, its development awaited the beginning of the Industrial Age. Organized coal mining began in Canada in 1825 with the formation of the General Mining Association. This British firm was the creation of a group of London jewellers which had been granted royal rights, by the British crown, to all minerals in Acadia (substantially the present Maritime Provinces). The Association took over a number of existing small mines and opened up larger operations in the Sydney coal field. Subsequently, it expanded to the mainland Nova Scotia fields at Stellarton and Springhill. The Association continued in existence as the major coal producer in Canada until 1899 when it sold its properties to the Nova Scotia Steel and Coal Company, Limited (3). This Montreal-based firm managed the coal mines as a major Canadian producer of coal until 1968 when financial problems led to the expropriation of the mines by the Government of Canada. The federal government established the Cape Breton Development Corporation to operate the larger mines on Cape Breton Island. This Crown corporation continues to be a .major producer of coal in Canada."

Jan 1, 1985

By R. D. Brown

"Finance Minister Donald Macdonald's budget of May 25, 1976 featured a restructuring of the anti-inflation profit controls and a grab bag of tax changes, some of direct interest to the mining industry. All Canadian taxpayers now will be permitted to write off immediately 100% of mineral and oil and gas exploration expenses included after• May 25, 1976 and before July 1 1979. The cost of acquitting Canadian resource property after May 6, 197.4 from a federal or provincial government will now clearly be included in Canadian development expense, and provincial drilling and exploration incentives received after May 25, 1976 will not reduce exploration and development expense for federal income tax purposes. Under tough new anti-inflation profit controls, all controlled businesses, except distributions, will essentially have one uniform set of rules for• determining allowable profit margins; this allowable margin will be determined by product line or by over-all net margin and will be 85% of the higher of the margin obtained in the five years preceding October• 13, 1975 or the one year preceding May 1, 1976. The basic capital cost allowance system is to continue, but many rates will be revised. The ability to offset losses created through claiming capital cost allowances on leased equipment, etc. against other income will be ended with respect to transactions entered into a/te1• budget night. Miscellaneous other tax changes will raise the low rate base for Canadian-controlled private corporations to $750,000 increase retitement plan contribution limits and reduce the rate of branch tax imposed on branches of corporations resident in a country with which Canada has a comprehensive tax treaty to equal the withholding tax rate on dividends under that treaty."

Jan 1, 1976

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By Gillyeard J. Leathley

The Cassiar Asbestos mine is situated on McDame Mountain in northern B.C. at a mean elevation of 6000 ft (1830 m), some 6 miles (9.6 km) from the townsite /mill complex. Asbestos ore production averages 1,200,000 tons at 9% R.M.G. (Recoverable Mine Grade) and waste production is 6,000,000 cu. yd annually. Waste is loaded by P&H 1900 AL 11-cu.-yd shovels and transported by 75-ton and 85-ton end-dump trucks to the waste dumps. The ore is loaded by a 992 Caterpillar 10-cu-yd front-end loader into 50-ton and 75-ton trucks, which transport it to the crushing plant located at the mine. The ore is transported by a 15,370-ft (4685-m) tramline to the mill complex.

Jan 1, 1978

By Q. Han

A modified cast-on method has been developed to reinforce aluminum castings with steel insert. Defect-free bond between the steel insert and the aluminum casting has been consistently obtained. Data obtained from a push-out experiment indicated that the bond strength was much higher than that obtained using the Al-Fin approach. This paper introduces this modified method in four sections: the coating of the steel pins, the cast-in method, microstructure characterization, and the bond strength. The section on the coating of the steel pins contains coating material selection, electro-plating technique for plating Cu and Ni on steel, and diffusion bonding of the coatings to the steel. The section on cast-in method deals with factors that affecting the quality of the metallurgical bond between the coated steel and the aluminum castings. The results of microstructure characteristics of the bonding are presented in the microstructure characterization section. A push-out experiment and the results obtained using this method is described in the section of bond strength/mechanical property.

Jan 1, 2015

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By I. Ruiz Bustinza, L. F. Verdeja, Daniel Sbarbaro, R. Parra, J. Mochón

The oxidation of sulfides is a complex process involving gaseous products and intermediate species given rise to emission and absorption spectra which carry out important information about the reaction process. This information could be used for on line monitoring of pyrometallurgical reactor if the appropriate sensors were available. We present in this paper an analysis of the concept that has been successfully applied in iron and steel making industry, as well on fuel combustion control, where the spectra measurement gives the possibility for online monitoring and automatic control of high temperature processes. This concept has not been widely applied in the nonferrous pyrometallurgical primary production. The design of new sensors is discussed from the analysis of spectra measurements during flash combustion of copper concentrates at laboratory scale.

Jan 1, 2015

By W. Petruk

Mineralogical studies and concentration tests were conducted on samples from an oolitic iron deposit from the Peace River district in Alberta to determine what concentrate grades and metal recoveries could be obtained. The samples assayed 32 to 37 wt. % Fe, and consisted of goethite, nontronite, ferruginous opal, siderite , quartz, amorphous phosphate and illite . Flotation with fatty acids yielded the best over-all results. A flotation concentrate from a composite sample of the iron horizon assayed, by weight, 43.0% Fe, 12.3% SiO2 , 1.9% CaD, 0.9% MgO, 4.5% Al2O3 and 2.0% P2O5 and lost 17.2% on ignition, for an iron recovery of 48.8% and a silica rejection of 80%. When heated to drive off the water, the concentrate assayed 52 w t. % Fe and 14. 8% w t. % SiO2

Jan 1, 1977

By W. L. Sherwood

Present conventional techniques for primary steelmaking in both integrated and non-integrated plants are outlined. 'Direct reduction' alternatives are reviewed and categorized according to the nature of the product produced, with particular emphasis on the limited number designed to yield steel as the end product. A proposed new technique, referred to as the Sherwood Process, is described in some detail as a new combination of selected features from the prior technology. This process is in-tended to realize, in integrated operations, the result of continuons steelmaking directly from the ore in a single plant and, in non-integrated operations, continuons steel-making from a metallic charge of scrap, sponge iron or pig iron. Prominent features are continuons processing in elongated, horizontal, rotary furnace equipment, controlled direct heating of each process stage and, for the over-all integrated process, a size separation for removal of excess solid reductant and other waste just prior to the melting step. Material and energy balances are presented as well as exemplary cost data. Reasons for selecting this particular combination of process elements are dis-cussed.

Jan 1, 1968

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By C. Jay Hodgson, P. J. MacGeehan

"Of the 135 current or past-producing 'gold-only' mines in the Superior Province of the Canadian Shield which have produced more than 100,000 tons of ore, the 33 mines which have produced one million ounces or more of gold have accounted for over 84o/o of the total production of 137 million ounces. The published literature on these 33 deposits was reviewed in order to determine the geological setting of the mineralization on a regional (mining camp) and local (mine) scale. The dominant rock types underlying the mining camps are mafic, variolitic, tholeiitic volcanic rocks with a significant ultramafic (komatiitic) component, and clastic and/ or exhalative sedimentary rocks. Felsic volcanic rocks are generally subordinate. Most mining camps are located at or near the top of the mafic-ultramafic sequence, and generally there is a major sedimentary-volcanic contact present which may be 1) a stratigraphic superposition of volcanic and sedimentary units, 2) a rapid, along-strike gradation from dominantly volcanic to dominantly sedimentary units due to facies change, or to the formation of structurally controlled sedimentary basins during volcanism, or 3) frequently (at 40o/o of the camps) a juxtaposition of sedimentary and volcanic sequences across a major fault zone or 'break', which in many instances may represent a reactivated, syn-volcanic basin-margin fault.In contrast to the regional setting, on a local or mine scale over 90o/o of the 33 mines contain felsic intrusions and/ or extrusions within mine workings. The felsic rocks may be quartzbearing (commonly quartz-feldspar porphyries) or dominantly quartz-free (commonly feldspar porphyry syenites or monzonites), and appear to have been emplaced in two different depth-zone environments: an epizonal intrusive environment, and a volcanic vent environment. Although the distinction between epizonal intrusive and volcanic intrusive-extrusive rocks is uncertain in many deposits, the two are tentatively separated on the basis of the grain size of the rock matrix (medium to coarse grained vs aphanitic to fine grained), homogeneity (multi-phased and/ or compositionally zoned vs compositionally homogeneous), and the shape and relationship to stratigraphy of the igneous body (circular or oval in cross section, and cutting the stratigraphy at a low angle vs lenticular and either stratiform or cutting the stratigraphy at a high angle). In addition, felsic intrusions of the volcanic environment commonly grade into tuffs or breccias of extrusive origin, whereas epizonal intrusions do not.Stratiform ore zones of possible exhalative sedimentary origin appear to be confined to deposits in which volcanic felsic rocks are present, and are absent from deposits in which only epizonal felsic intrusions are present. Pervasive carbonate- rich alteration, commonly in roughly stratabound zones of regional extent, and carbonate-rich chemical sedimentary rocks are present in over three-quarters of the deposits containing quartz-bearing felsic volcanic rocks, but are much less common in deposits with quartz-free felsic volcanic rocks. The host sequences of epizonal felsic intrusions which are quartzfree are more commonly sedimentary than those of quartz-bearing epizonal felsic intrusions.Quartz, carbonate minerals, arsenopyrite, scheelite, tourmaline and Cr-muscovite ('juchsite') are the most common mineralogical associates of gold. Arsenopyrite is essentially restricted to the volcanic environment, occurring in about twothirds of the deposits with quartz-bearing felsic volcanic rocks and less than half of the deposits with quartz-free volcanic rocks. Tourmaline, on the other hand, is almost ubiquitous in deposits associated with epizonal intrusions and also occurs in about two-thirds of the deposits associated with quartz-bearing felsic volcanic rocks, but in only one of the eight deposits associated with quartz-free felsic volcanic rocks. Scheelite is essentially restricted to ores of quartz-rich fel"

Jan 1, 1982