Search Documents

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By Manqiu Xu, Peter Wells, Gord Bacon

"A methodology is proposed for milling flowsheet design using flotation rate, selectivity and residence time distribution data. The flotation rate data and the difference in flotation rates between the main minerals to be separated are determined from laboratory batch tests. The residence time distribution (RTD) data is calculated using the tanks-in-series model assuming each flotation cell is a perfect reactor. The rate, selectivity and RTD data can be used to calculate the optimum flotation cell number in a bank for rougher/scavenger in a commercial plant.This methodology is demonstrated in a case study of a nickel sulfide ore. It is shown that miniplant rougher/scavenger data can be closely predicted from a batch test using the proposed methodology.INTRODUCTIONIt has been the trend in the past several decades that large flotation cells are increasingly used. This is largely driven by the economics as ore grades are getting lower and the rate of ore processing must be increased in order to keep mining operations economically viable. The development and evaluation of 250 to 500 m3 WEMCO SmartCell and Outokumpu TankCell flotation machines are well in progress. There are many advantages in using large cells: fewer cells, less floor space, lower power cost (although this is now being questioned for fine particle flotation), simpler circuit, simpler control, and lower auxiliary equipment cost (Arbiter, 1999). As flotation cells are getting larger, the importance of cell hydrodynamics, namely, air/slurry dispersion, power intensity, froth transfer, residence time distribution (RTD) and short-circuiting are being fully recognized (Jonaitis, 1999; Weber, et al., 1999; Gomez and Finch, 2002). It is not the intention of this paper to discuss flotation cell scale-up. The intention is to answer what is the optimum number and size of cells in a flotation bank for a given throughput. Figure 1 illustrates this problem facing design engineers. The same mean residence time required for a given throughput can be achieved in a single large cell, or many smaller cells in a row. A few cells of large size may be more cost-effective but they may not be as effective as more cells of smaller size in achieving the optimum metallurgy."

Jan 1, 2005

By Lian-Jin Tao

With fast development of China modernization, road construction obtains great achievement. However, in the construction process of highway, especially the high-grade highway in mountainous area, there are many unavoidable high cut slopes. Specifications for Design of Highway Subgrades, China, prescribe that the design scheme of slope with height more than 30m should be compared with bridge scheme and tunnel scheme economically. In spite of the existing guidelines, it is still quite common to see many high slopes due to engineering geological conditions, highway line shape, cost and issues related to traditional design ideas. Actually the traditional way with ?high backfill, the high cut? for mountainous highways seriously damages the original ecological environment and groundwater system, especially to those area with weak ecology, where the damage is unrecoverable. It is quite common practice to use artificial vegetation for cut slope virescence, however it still has problems such as low ratio of survivor, high maintenance cost and lack of species diversity. Now people are more and more aware of the importance of ecological environment, it becomes urgent to decrease the damage to ecological environment after ensuring the stability of high slopes. With the aim to reduce ecological damage, we proposed a new design approach which is ecological environment friendly by decreasing cut slope height with steep excavation scheme. This approach requires that (1) the geological condition is good, and the rockmass can be sTable itself; (2) excavation should not badly damage the rock, which means blasting must be controled by using buffer blasting, smooth blasting and pre-splitting blasting; (3) if local geological condition is not very good, excavation should have intervals for one bench, the advised space is 20m; (4) to ensure the slope stability in construction process, the cut slope should be reinforced more strongly than usual and in time. Finally, the deformation of the slope and the working condition of the reinforcement structure should be monitored to ensure the slope stability. The new design is used to a roadside cut slope of provincial trunk highway S223 in Guangdong Province. Based on intensive geological investigation and borehole tests, it is found that the slope rock mass is intact and sound, and the rock strength is quite high. Results from numerical modeling by UDEC reveal that compared with the traditional design scheme with 90.23m high slope, the steep scheme with only 23.46m high is characterized by its relatively large deformation and stress concentration, however the influenced area only appears at the upper slope and tends to sTable. With cable reinforcement, the stability of slope excavated steeply can be guaranteed. Deformation of the slope and the cable force are monitored in details in the period of construction, which show that the deformation of the slope decreases gradually and the final deformation is very small, and the cable tensions change small after the cables were tensioned. It is optimistically estimated that the steep slope should be sTable during operation. Comparison analysis between the steep scheme and the common scheme affirms that the steep excavation is better than the traditional scheme in terms of ecological environmental effect, slope height, the excavated amount, the excavated quantity of slope surface, engineering cost. It is concluded that if geological condition permits, the steep cut scheme should be used with better benefits.

May 1, 2009

By R. Venugopal, Saxena. V. K., U. Sankrityayan

"There is a dire need of a technology which can break the mineral interfaces to enhance liberation with minimum energy consumption in mineral beneficiation processes. Understanding of mineral crystal system and interfaces is essential to develop such methodology. So, this study is carried out to find out the role of mineral crystallography in milling and liberation. Data related of mineral crystallography, Vickers Hardness Number, Bond Work Index and beneficiation processes were collected from literature and detailed statistical analysis has been carried out to establish a correlation among these parameters. It was found that atomic weight and cell parameters shown statistically significant relationship with Vickers Hardness Number of minerals, which controls the milling characteristics of ores. Liberation characteristics of five different kinds of ores were analyzed considering the types of interfaces between valuable and gangue minerals. It was found that phase interfaces play vita role in liberation and coarser liberation can be achieved in the minerals of incoherent crystal systems like manganese and zinc ores. Study of this subject can help us to understand the effect of stress wave propagation in solids and its effect on crystal interfaces. It can also help us to design a technology of future to break the mineral interfaces.INTRODUCTIONCommunition is energy intensive mineral processing operation and consumes up to 2% of the total electric power generated in the world. Energy consumption due to comminution is increasing every year as there is growing needs to exploit lower grade ore bodies and process rejects (Blazy et al., 1994; DOE, 2005). Low grade ores require crushing and grinding to liberate the valuable minerals which are further separated from gangues by various beneficiation methods like gravity separation, floatation, leaching etc. Currently, comminution methods are selected based on the reduction ratio and energy consumption but effect of grinding methods on subsequent processing methods specially on liberation also need to be studied to optimize the entire beneficiation process. Most of the attempts made in past to minimize the energy consumption in milling to enhance the mineral liberation were focused on compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Kilpelm and Austin, 1982; Norgate and Weller et al, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang el al., 2011; Singh et al., 2012). But the role of mineral crystallography on milling and liberation behavior of minerals not fully explored yet."

Jan 1, 2013

TABAKOTO / SEGALA ? Annual gold production approximately 100,000 oz ? Debt free ? Unhedged ? Combined surface reserves 949,000 oz ? Combined 9 year life Tabakoto open pit reserve 568,000 oz (3.4m tonnes @ 5.26 g/t Au) Segala open pit reserve 381,000 oz (3.98m tonnes @ 2.98 g/t Au)

May 1, 2006

By Richard F. Lynch, Frank E. Goodwin

"The development of Galfan, a new generation 95% zinc-5% aluminum-mischmetal alloy coating for steel, offers opportunities for greater fabrication flexibility and upgraded corrosion performance in automotive applications. The formability of Galfan is equivalent to that of electrogalvanized steel, based on laboratory tests and automotive component fabrication. Corrosion resistance of Galfan exceeds that of hot dip and electrogalvanized, including performance in automotive industry tests. Automotive production applications for deep drawn and stamped components in France and Germany are based on the ability to meet dual performance requirements for upgraded formability and corrosion resistance. The first U.S. Galfan application was on 1985 model Ford cars and light trucks for transmission oil cooler lines which has now expanded into a number of power steering tubing uses. IntroductionContinuing requirements for improved vehicle performance coupled with the ever present need for reduced cost have spawned the development of a number of new coated steel products. Among this new generation of coated steels is Gaifan™, a 95070 zinc-Solo aluminum-mischmetal hot dip alloy coating. Galfan exhibits particular promise for automotive use based on broad fabrication advantages and upgraded product performance(I ),The unique characteristic of Galfan is the key combination of greatly improved formability with much longer corrosion life. Galfan provides significantly better formability than any other hot dip coating. Testing shows that formability is limited primarily by the steel substrate to which the Galfan coating is applied. Galfan exhibits excellent resistance to flaking and microcracking during commercial forming operations. The result is the elimination of unnoticed damage to the coating which would show up later as premature rusting on the finished product."

Jan 1, 1987

Stress induced, gravity-assisted failure processes typically dominate long before stress levels approach the strength of the intact rock (at approximately smax > 0.4UCS where smax = 3s1 ? s3 and UCS is the Unconfined Compressive Strength of the intact rock (Martin et al. 1999)). Under these conditions, discontinuities typically become clamped and the failure process becomes brittle. This brittle failure process is dominated by new stress induced fractures growing subparallel to the excavation boundary. While it is possible to identify areas with the potential for brittle failure, for example, using the general assumption that brittle failure will occur in areas at right angles to the major principal stress (Hoek et al., 1995), when the threshold smax > 0.4UCS is reached in areas around the tunnel boundary, or elastic modelling and the Hoek-Brown brittle parameters proposed by Martin et al., (1999) (i.e. m? 0 and s ? 0.11), amongst others, recent observations discussed by Everitt & Lajtai (2004), and Kaiser (2005; 2006) suggest that brittle failure processes are enhanced when structural features such as joints, weakness zones, bedding planes or foliations are preferentially orientated around the excavation boundary creating stress raisers which in turn facilitate the stress-driven rock mass disintegration process (e.g., as illustrated by Everitt & Lajtai (2004) on Figure 1b). Such weaknesses induce stress heterogeneities that thus promote tensile-spalling failure processes (Diederichs 2000). The observations suggest that stress induced damage can occur ?prematurely? depending on the orientation of micro and macro structures in situations where the known stress conditions should not yet initiate brittle failure processes. In general, when structural features (micro and/or macro), especially foliations, are present in a rock mass, the strength is effectively reduced, largely due to tensile strength heterogeneity in areas depending on the orientation of the structural features with respect to the excavation boundary. As a result, stress induced damage could occur in areas not normally considered due to the influence of anisotropy (Figure 1).

May 1, 2009

By Joseph L. Fournier

Suncor Oil Sands employs delayed coking technology in converting bitumen into synthetic crude oil. Currently up to 10,000 m3 of delayed coke (coke) is produced per day as a byproduct of the upgrading process, of which up to 9,000 m3 per day is placed in dry storage on Lease 86/17. A review was completed to examine the case history of leachate potential experiments from the dry storage of coke and the environmental relevance of coke leachate studies conducted over the past decade. The review included an evaluation of the potential impacts of environmental conditions within the location of coke storage, including precipitation pH, as well as daily and annual ozone trends. Coke leachate potential has historically been characterized using standard leachate testing protocols (i.e., TLCP, SPLP) together with other studies that have employed strong acids and oxidizing agents in the extraction fluids. The present paper highlights prevailing conditions in the Athabasca Valley air-shed with emphasis given to ambient ozone (oxidizers), as well as precipitation pH and acid input deposition rates, and will demonstrate that TCLP / SPLP tests lack the intended environmental relevance relative to the conditions under which coke is stored.

May 1, 2011

By M. P. Hay

"For a model to be successful it must address the concerns and needs of a target audience. Further, the model must demonstrate the same patterns of behaviour as the real system, and need only be complex enough to meet this objective. If the model is too complex it can become unusable to those who need it most.With this in mind, SUPASIM has been developed for the practical metallurgist requiring only laboratory flotation rate data as input. Some 35+ successful plant simulations have been completed since 1985. The approach of SUPASIM is to characterise an ore, organise information in an understandable way and add structure to the complex flotation situation and hence support the metallurgist to interpret the relationship between variables and optimise the flotation process.The paper describes the basis on which the model was developed and sets out to provide an insight into interpreting laboratory flotation kinetics and their physical meaning in a production plant and the influence floatable gangue has on float performance and plant design. A case study illustrates how the ratio of slow floating mineral to gangue can influence circuit design and improve recovery on a plant scale.INTRODUCTIONThere is an enormous amount of useful data in the results of a laboratory scale rate test. Each variable of fraction and rate, for mineral, metal and gangue has a physical meaning in the plant. The link between float kinetics and the plant in respect of recovery, grade, pulp density, pulp flowrate, residence time, number of stages of cleaning and circuit configuration has been established by the author in the process of developing SUPASIM."

Jan 1, 2005

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill? has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill? technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill? has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills? are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill? in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By Guy Archambault, Réal Daigneault

"Un trait marquant du cadre tectorwstratigraphique de la Sous-province de l'Abitibi est la présence de nombreux couloirs de déformation d’extension régionale et sub-concordants au grain stratigraphique. La présence de grandes masses granitoïdes qui perturbent l'allure du grain tectonique est typique de la partie nord de la Sous-province de l'Abitibi. Des rides E-W constituées de complexes plutoniques précoces forment des reliefs structuraux agissant comme des moles résistants qui interfèrent avec la déformation régionale.Deux types de couloirs de déformation sont distingués, les couloirs de bordure et les discontinuités structurales. Les couloirs de bordure représentent des auréoles de déformation élevée qui s’accompagnent généralement d’un métamorphisme au faciès amphibolite. lls suivent /'interface entre les roches granitoïdes et les assemblages supracrustaux. Ces couloirs sont de puissance kilométrique et sont confines, surtout au sein des roches vertes, a l’interface des complexes granitoïdes d’importance. La limite entre la Sous-province de l'Opatica et les roches supra crustales de l'Abitibi est caractérisée par un important couloir de bordure issu possiblement d'un chargement tectonique irrégulier et concentre lors du raccourcissement horizontal.Les discontinuités structurales sont des failles ductiles qui se propagent surtout en direction E-W mais avec des variantes de directions SE et NE. Les discontinuités E-W se caractérisent par la présence d'une linéation d'étirement à fort angle de chute. Les discontinuités SE sont caractérisées par des linéations d'étirement horizontales et directionnelles et les mouvements observes sont system attiquement dextres. Les discontinuités NE sont des failles à comportement beaucoup plus fragile et se distinguent par des composantes de mouvement senestre. Elles sont tar dives par rapport aux discontinuités E-W et SE et ne représentent pas la symétrique du système SE.La combinaison des systèmes E-W et SE décrit un motif anastomose a l' échelle régionale. Les failles ductiles se rejoignent defaçon asymptotique, isolant des blocs peu ou pas affectes par la déformation. L'anastomose est un phénomène qui se produit a toute échelle et est reliée principalement aux Mt érogénéités et aux anisotropies 1) des forces agissantes (champs de contraintes régionale et locale) et 2) de la réponse del' empilement supra crustal (compositions différentes, fabrique initiate, propriétés mécaniques variées, niveaux d'altération).Dans le but de respecter un raccourcissement horizontal N-S, différents modelés sont proposés; ils mettent en cause soit une transpression dextre, soit des failles inverses réactivées en failles décrochèrent dextres soit des failles de chevauchement redressées."

Jan 1, 1990

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By J. Ran

Ground instability is among the major causes of serious incidents and production disruptions in the mining industry and has a significant impact on safety. Mining companies may have operations in a number of jurisdictions with varied regulatory requirements for ground control management. As these companies expand into countries where mining regulations are formative or lacking clear definition, ground control practices are usually developed by local mine personnel based on their experience. In many cases, inconsistent procedures and standards are generated, which can lead to an increase in occurrence of underground incidents due to difficulties and confusion in implementation. This situation has forced some mining companies to standardize their ground control practices by geographic regions or divisions. Though this approach is an improvement, it may not lead to effective management of ground control issues across all operations of a global mining company. Barrick Gold Corporation, with operations in North and South America, Australia and Africa, decided to adopt a global approach to ground control management. This global approach requires all Barrick operations to prepare and implement an effective ground control management plan (GCMP) based on site specific conditions and company guidelines. It is also required that the GCMP be developed through application of sound geotechnical engineering practices and be consistent with local regulatory requirements and Barrick safety policies. All Barrick underground operations have GCMPs in place, and its surface operations are now involved in the initiative. This paper presents Barrick?s global approach to underground mine ground control management and outlines the content and process for the development of a GCMP.

May 1, 2006

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By Trevor Harris, Martin Harris

"This paper evaluates the effect of grind size on the flotation performance of a platinum ore from the UG2 reef of the Bushveld Igneous Complex, in South Africa. The study was conducted on the Mintek Flotation Pilot Plant Facility, located in Johannesburg, and represented a thorough evaluation of the application of the flotation modelling methodology developed jointly by the University of Cape Town and the Julius Kruttschnitt Mineral Research Centre at the University of Queensland through the AMIRA P9 Project. A simulation model of the pilot plant data was successfully implemented, providing a set of circuit modelling parameters that appeared to be both consistent and well correlated to measurable characteristics of the ore and the pilot circuit operating conditions. The findings indicate that the methodology that was used could well provide a useful framework for developing optimisation criteria for industrial flotation circuits in combination with appropriate feed grind size and regrind size targets.INTRODUCTIONIt has long been recognised that the size distribution of an ore is one of the most important factors in the determination of the performance of a flotation process. It therefore follows that the optimisation of a flotation plant cannot be considered without due recognition of the interdependence of this process with the process of comminution. There are numerous qualitative guidelines for the selection of an optimum grind target for a particular operation. Mineralogical analysis can readily provide information on liberation as a function of grind, and the desirable particle size range for optimum mineral flotation is well established in both theory and practice (see for example Trahar, 198 1). For some operations, meeting these two criteria simultaneously is relatively simple. For the majority of operations, such mineralogically “easy” deposits, if they ever existed, have long been exhausted, and the optimum grind represents a highly complex compromise between liberation and overgrinding of both desirable minerals and gangue. This is particularly true for circuits that include regrind stages, where both primary and secondary (and sometime even tertiary) grind targets must be specified. As has been pointed out in a recent paper by Bazin and Hodouin (2001), there is little or no information in the literature to assist plant engineers in the selection of optimum grind targets for complex ore deposits, so current practice is primarily based on rules-of-thumb and experience. This problem is further compounded by the fact that once grind targets have been selected for a particular operation, the assessment and adjustment of these targets based on plant surveys is extremely difficult, time consuming and expensive, and is often not attempted unless the plant significantly underperforms relative to expectation. It is therefore clear that the development of a practical quantitative approach to this problem is a high priority for flotation research and development studies."

Jan 1, 2002

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By Stephen J. Roberts

Gold catalysts were prepared on co-precipitated, calcined copper oxide - zinc oxide support by an inverse deposition-precipitation method. These catalysts were characterised by X-ray diffraction (XRD) and temperature-programmed reduction (TPR) and studied for CO oxidation activity at various catalyst calcination temperatures. TPR studies of the support material exhibited a double peak and shift to lower temperatures for the reduction of Cux+ to metallic copper, as opposed to the single reduction peak for pure CuO. This phenomenon is possibly caused by an interaction with the zinc oxide. The addition of gold to the support CuOZnO led to a further shift in copper reducibility to lower temperatures. Gold present in the initial uncalcined catalyst as Au3+ was auto-reduced to Au0 under various calcination temperatures. The Au3+ reduction peak was observed to shift to lower temperatures with increasing calcination temperature. The catalytic activity was found to pass through a minimum value with respect to calcination temperature. Catalysts with both gold in entirely the 3+ or metallic oxidation state were found to exhibit high activity. Furthermore, the catalysts were found to decrease in activity with decreasing Au3+ content up to an intermediate calcination temperature, afterwhich the activity increased sharply. Possibly at higher temperatures, a stronger Au-support interaction is formed, leading to a new active site.

Oct 1, 2003