Search Documents

By D C. Verdon-Kidd, G R. Hancock, M J. Saynor, J B. C Lowry, T J. Coulthard

Designing post-mining landscapes requires quantifying the short and long-term risks. In recent years, computer based landscape evolution models (LEMs) have been used to provide insight into both erosion rates and processes (i.e. sheetwash, rill, gully erosion). An important requirement of these models is high quality model input parameter data, which includes both the surface material (i.e. soil and waste rock) and climate information. However, in many cases such data is limited and in the case of climate information, the data is often short and incomplete. Here we develop climate scenarios and examine different surface material properties using a case study at the ERA Ranger mine located in the Northern Territory, Australia Firstly we develop scenarios that represent the range of future climates that may be experienced at the site. Secondly we develop a series of plausible particle size distributions based on a large sampling exercise of the waste rock material. We then test the sensitivity of different rainfall sequences and surface materials on sediment output using a well-tested landscape evolution and sediment transport model (Hancock et al., 2017). CITATION:Hancock, G R, Verdon-Kidd, D C, Coulthard, T J, Lowry, J B C and Saynor, M J, 2018. Quantifying the effect of climate and surface materials on post-mining landscape erosion – a risk approach using landscape evolution models, in Proceedings Life-of-Mine 2018, pp 122–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The geotechnical factors controlling the design of the open pit slopes of the Pasminco Century Mine near Lawn Hill, Queensland are presented below. Pasminco Century is a stratiform shale hosted zinc deposit in the Lawn Hill Formation that is overlain in part by the Thorntonia Limestone Formation. Both the mineralisation and overburden is located within a competent rock mass such that intact rock strength and discontinuity spacing is generally sufficient to prevent large-scale slope failure by breakage through the rock mass. Rather, overall slope stability issues are dominated by the major discontinuities within the rock mass. The deposit is located in a structurally complex regime, it consists of a synclinal basin which is truncated by easterly striking normal faults through its centre and northern and southern limits and by an unconformity on its eastern and western margins. Deposit geometry and slope stability is further complicated by small-scale folding, a pattern of northeast and southeast striking subvertical faults and north easterly dipping thrust faults with their associated fault emplaced blocks of Lawn Hill Formation in the overburden. The large size of the deposit requires a staged mining approach with the excavation of both final pit walls around the external sides of each stage and interim pit walls along the internal boundaries between adjacent stages. The deposit geometry and major discontinuities control not only the final pit wall design but also interim wall location and orientation, excavation sequence and in some stages the excavation schedule. Two and three-dimensional limit equilibrium stability analyses were conducted using both deterministic and probabilistic approaches to determine appropriate pit wall design criteria and to select a suitable excavation sequence and schedule.

Jan 1, 2000

Human resources (HR) practitioners use a general suite of tools that they adopt to suit their company needs and profile. This paper will cover the main areas of a selection and recruitment process from applying for a job, resumT writing, participating in an interview finalising the job offer. A holistic recruitment process has many facets to it. These processes can be quite sophisticated and technical but at the end of the day they are designed to identify talent. A recruitment process will generally include: ability testing (usually online);telephone interview;face to face interview;behaviourally based interviews;psychometric assessments;presentations;simulations (independent or team based); and assessment centres, etc. Understanding the basis of these tools will go a long way to prepare you for the job market, enhance your performance in a recruitment process and stand you out from the pack.

Jan 1, 2008

By M Akbarpour, M Osanloo

In mining industries, materials handling costs represent a significant component of the operational cost. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading system with the lowest loading operation cost. These are queuing theory, bunching theory, linear programming and genetic algorithm. Among them, genetic algorithm is a simple method and applied for preliminary selection of the loading system. In this study, gathering information from anomaly No 2 of Gol-e-Gohar iron mine of Iran, loading system (number and its capacity) has been optimised by genetic algorithm. The study results showed that two shovels 8.25 m3 are required for the removal of 60 million tonnes of overburden. After removal overburden, these two shovels contribute to the extraction of 42 million tonnes of ore with a stripping ratio of 1:1.

Jan 1, 2007

Mining and metals projects have tended to increase in both scope and cost to a point where many projects are Droperly designated as superprojects. Specialist engineer- constructors have developed organisations and systems to provide project management services during the design and construct phase of large projects. However, the engineer-constructor is also required to provide a wide spectrum of services during the evolution of large projects prior to the construction phase. Some common phases of pre-construction evolution are identified together with the associated types of specialised services which may be required. A project management team approach is described which has been developed for the design and construct phase. It is suggested that a modified matrix organisation could be adapted to the provision of special- ised services as well as to project management for ore-construction phases of the project.

Jan 1, 1980

By J J. Cilliers, K Hadler, A W. Stra

This paper examines the use of the FrothSim flotation simulator to improve the performance of an industrial column flotation cell. The performance of an industrial retreat column cell is simulated, and, from the discrepancies between the simulated and experimental results, a problem with the wash water distribution is postulated. The scientific reason for the reduced performance with uneven wash water addition is described in detail. Further simulations indicated the potential for improvement with an even wash water distribution, resulting in both improved performance and reduced wash water usage. The simulated uneven wash water distribution was confirmed industrially, and the headers were redesigned and installed. A sampling campaign to compare the performance before and after the modifications showed that the flotation performance was improved dramatically, with a statistically significant decrease in gangue recovery, without a commensurate reduction in valuable mineral recovery.

Jan 1, 2005

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Reid JG, Cutfield S

Considerable quantities of dissolved nickel are lost in the waste liquors from the QNPL nickel treatment plant. Cementation, precipitation and ion exchange techniques were investigated to reduce this loss. Ion exchange was the most successful of the procedures studied and a process for recovering nickel from stripped ammoniacal process liquors was developed in the laboratory and scaled up to plant flow volumes. The system developed uses a carboxylic ion exchange resin operated in a completely ammoniacal cycle. The regenerant is itself regenerable using existing plant, thus the only loss is the stoichiometric value of NH4+ required to displace the exchanged cations from the resin. Existing plant sand/anthracite filter beds have been adapted for use as resin columns containing 3 cubic metres of resin capable of treating effluent at a flow rate of 6000 litres/min.

Jan 1, 1978

Copper refining electrolytes are maintained in the range 60-65¦C to ensure an efficient operation. The heat energy required to meet these temperatures has been traditionally derived from the electrical energy required for the electrolytic process and supplementary steam energy. In 1983, experiments were conducted at Copper Refineries Pty. Ltd. (CRL) to determine the effects of insulating the Tank House cells, and fully covering the cells. The results of these experiments showed conclusively that greatly reduced steam consumption would be required to maintain electrolyte temperatures. These positive results led to an Energy Conservation Programme for the Tank House, and this was implemented in 1984. A computerised cell cover monitoring system was developed, and is used to control cell coverage and fluid balance. The experimental work and the benefits obtained since implementation of the programme are discussed.

Jan 1, 1985

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By Jackson S

An investigation into different aspects of importance in the understanding of explosibility of hybrid mixtures of coal dust, air and gases potentially found within mine workings through a comprehensive laboratory program of explosibility tests was conducted. Plotting of test results revealed that conditions of potential explosibility could be described using two dimensional flammability limit surfaces- for coal dust/oxygen; methane/oxygen; and coal dust/methane mixtures. From these plots, the three dimensional flammability envelopes defining the explosibility of the coal dust/methane/oxygen mixtures can be defined and illustrated for a coal sample. The surfaces of the three dimensional envelope describe limits which separate inert mixtures of coal dust and methane at varying oxygen levels from those concentrations which are ignitable under defined conditions. It is considered appropriate to generalise that the geometric shapes of these limit regions are applicable to all type classifications of coal dust. There are practical applications of these results to the underground environment.The action of free radical initiators in the propagation of a methane gas explosion was examined for its applicability to the flammability of coal dust/gas/air mixtures. The oxides of nitrogen or NO x radicals have influence upon the lean limits of flammability of hybrid mixtures and this is illustrated by use of three dimensional coordinate geometry. Gases can be introduced to the underground environment through the exhaust gases of diesel equipment. It is concluded that radical species can substantially increase the flammability of gas and dust flames and as a consequence raise risk of mine atmosphere explosibility.

Jan 1, 1998

By Raczej I, Defant M

Pre-Miocene igneous rocks from the Phili pine island arc are characterised by 87Sr/86Sr and 143Nd/144Nd ratios typical for intra-oceanic island arcs where sediment involvement in the magma genesis was minor. Lead isotopic ratios are similar to Indian Ocean MORB (Mukasa et al., 1986a,b). Pliocene to recent volcanics, however, have more radiogenic Sr and Pb and less radiogenic Nd, except for the volcanics of the Bicol Arc, which have similar isotopic signatures as the Pre-Miocene rocks. We suggest that Pre-Miocene magmas and Bicol-Arc magmas have been generated in response to the subduction of the Philippine Sea Plate, their isotopic characteristics reflecting the composition of Philippine Sea crust. The Bataan arc magmas may reflect the larger amounts of sediments available for subduction in the South China Sea, while magmas of the Mindoro Arc, which are characterised by the most radiogenic Sr and least radiogenic Nd, may have been contaminated by slivers of the Mindoro-North Palawan terrane, which have been carried down to mantle depths after the collision of this terrane and the Philippine arc in Miocene (McCabe et al., 1982). This interpretation implies that Nd (and by inference other REE) can migrate from the subducted slab to the mantle wedge. Thus, variable Nd-isotopic ratios in island arc magmas (e.g. Sunda, Lesser Antillas) may not he a primary feature of the mantle wedge but a consequence of the release of Nd from the subducted slab.

Jan 1, 1987

The south-east Missouri cobalt-copper-lead-zinc district is the worldÆs largest lead producer and a significant producer of by-product zinc, copper, cobalt, silver and cadmium. Current production in the district comes from six or seven mines in the Viburnum Trend. Most ores in the Viburnum Trend are characterised by a small number of minerals with simple compositions. Portions of some orebodies contain ores that exhibit greater variations in mineralogy, and these include shale-hosted lead- copper ores, bornite ores and nickel-arsenic sulfide ores. Ore textures include both replacement and open space filling textures, and the paragenetic sequence for the ores is characterised by repetitive periods of deposition of all of the ore and gangue minerals. Ore microscopy is an effective tool for not only the identification of the minerals and textures shown by the ores, but also to determine the mineralogy and textures responsible for beneficiation problems. An interesting variety of sedimentary and structural ore controls have determined the locations of individual orebodies in the district. Based upon the positions of orebodies with respect to Precambrian ridges and knobs, together with areal patterns of mineral/metal zoning, it is interpreted that the ore fluids came from diverse directions to form the deposits in the district. It is concluded that the Old Lead Belt subdistrict was mineralised by fluids that flowed from the north-east and north-west, the Fredericktown area by fluids from the north-east, the Indian Creek subdistrict by fluids from the north-west and the Viburnum Trend by fluids from the north-west and west.

Jan 1, 2008

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

From 1980 to February 1991 the Rosebery concentrator purchased ore from Aberfoyle's Que River Mine. Following the termination of the contract the concentrator reverted to treating Rosebery ore alone. Since that time it has become apparent that the circuit configuration employed was no longer optimum for zinc metallurgy. The circuit was designed to treat a difficult, slow floating sphalerite; however, the opposite was now found to be true. The sphalerite is fast floating and the circuit was cumbersome. During 1992 extensive circuit changes led to the provision of a simple open circuit flow sheet. The circuit is now easier for operators to understand and lends itself to improvements in process control. Middlings streams have been minimised, which produces a far more stable circuit. Significantly, it must be noted that the key to achieving potential results must lie in reducing variations within the process. A significant ore characterisation program has been undertaken, providing an insight into the metallurgical compatability of the ore to be mined. Using the information collected in this program, metallurgical recoveries and grades can now be predicted with a geater accuracy. Ore characterisation data suggests that an improvement from a 54 per cent zinc concentrate to a 57 per cent zinc concentrate should be achievable. By understanding the size-by-size mineral assemblage, a strategy for concentrate grade improvement has been developed. The requirements of the customer must in all cases determine the quality of the product. Pasminco is a fully-integrated zinc producer and as such significant gains can result by tailoring the concentrates to suit the Smelters.

Jan 1, 1993

By O Dahl, I M. Platten, E J. Sides

Many narrow-vein gold deposits are characterised by a high to extreme nugget effect and the presence of coarse gold. They rank amongst the most difficult of deposits to produce an accurate and precise resource estimate. This contribution presents a case study from the Nalunaq Gold Mine in Southern Greenland. The mine commenced operation in May 2004 and is currently operating at a rate of 400 tonnes per day, to produce about 100 000 oz gold per annum from a total resource base of 1.2 Moz. Mineralisation is characterised by quartz veins that are hosted within a shear zone that is continuous over about 1000 m. The principal orebody is the Main Vein structure, which ranges up to 3 m in width, maintains an average dip of 35¦SE, and contains significant gold grades (1000s g/t Au). Gold particles are often visible, with 25 per cent being greater than 250 microns in size. Variography using underground development samples indicates a nugget effect of about 75 per cent. For the 2005 resource estimate, a 2D metal accumulation ordinary kriged block model was used to produce a global grade for the Target and South Blocks of the Main Vein. Grade control chip-channel samples are collected from æshantyÆ drive footwalls, and used as the basis for both the kriged block model and to determine the grade of individual stope blocks by peripheral weighted averages. Geology plays a key role in mining efficiency, given the locally variable nature of the ore zone.

Jan 1, 2006

Address by the President (Mr B T Loton) in presenting the Institute medal for 1981 to Charles Wooller Marshall AO. Address by Charles Wooller Marshall AO after accepting the medal.

Jan 1, 1982

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998

By W J

Al ores arriving at the works which contain more than 3% sulphur, together with all sands and other fine residues, are delivered to the roasting department. Those that are in a coarse condition are first sent to the crushing plant, consisting of 15 in. x 9 in. jaw crushers and two No. 5 Krupp mills. The ore is here crushed through a quarter mesh screen. Any pyritic concentrates high in sulphur are given a preliminary roasting, to bring the sulphur contents down to about 12 % and the roasted material is delivered to the H. H. charge-making bins. Here the various ores, sands, residues, roasted pyrites, together with about 12 % of limestone, are made up into I-ton charges in hopper trucks with bottom discharge. The trucks are elevated by hydraulic lifts to a tramway running over the roasting furnaces, and the contents are dropped into hoppers over each furnace, from whence the mixture is fed into the centre of each furnace by means of a Challenge ore-feeder.

Jan 1, 1918