Search Documents

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By K M. Brodie, D I. K McLeod, J Ruddock

Environmental incidents involving mine tailings and waste rock inevitably become highly publicised and serve to damage the credibility of the entire industry. The recent serious incident involving a spill from a Romanian mine, was blamed for triggering æone of the worst environmental catastrophes in Eastern EuropeÆ. It is important to clearly demonstrate to the general public that these incidents are not representative of the industry as a whole. Where such incidents have occurred, the causes are generally related to poor design and/or construction, inadequate supervision and/or monitoring and maintenance, lack of independent expertise, inadequate risk identification and treatment and no provision to ensure that rehabilitation and long term management of the site occurs. Many people are unaware that these issues have been considered and provided for at the Martha Mine. Despite the fact that the first tailings storage facility has performed very well over fifteen years of operation, the long term safety and security of the tailings storage facilities continues to be questioned and debated by the public. The best way to address this is to provide quality information to enable a better understanding amongst the general public.

Jan 1, 2002

By J Mar·n, R Anderson, S Strohma, R Harvey

Xstrata is the operator of both Minera Alumbrera Ltd (50 per cent Xstrata, 50 per cent Wheaton River) and Ernest Henry Mining Pty Ltd, (99.99 per cent Xstrata), both copper-gold deposits, using conventional SAG/ball milling at current capacities of 36 Mt/yr and 10.3 Mt/yr respectively. Alumbrera is located in Catamarca Province, in the north west of Argentina. Ernest Henry is located in Cloncurry, north west Queensland, Australia. Both operations started in late 1997, with commercial production achieved in early 1998. Different designs and equipment are in use for both operations, however the evolution of SAG milling performance, although logically related to their specific features, reflect similar trends of consistent increases in throughput. This paper will discuss the main changes to the SAG mill liners in both operations and the results achieved to date. A summary of the operating strategies will be included.

Jan 1, 2003

The modern Golden Cross mine entered the production phase in January 1992. The project is designed to produce over 100 000 oz/yr of gold and over 300 000 oz/yr of silver during a mine life of eight years. An open pit and an underground mine are operated producing around 850 000 t/yr of ore, to feed a conventional carbon-in-leach processing plant. Golden Cross is owned in joint venture by Coeur Gold New Zealand Limited (80%) and Viking Mining Company Limited (20 %).   Since the start of production several major aspects of the design have altered. The underground mine began as a mechanised cut and fill operation. The cut and fill stoping progresses in 3.3 m flatback lifts with maximum stoping width of 6 m. Where the ore zone is wider than 6 m a post pillar cut and fill method is used. In 1993 a new bench mining plan was introduced between the 270 and 260 levels. Flatbacking continued in the footwall drives in anticipation of variability of the ore width and orientation. The development of levels below the main service 200 level has indicated a possibility of bulk mining the ore block rather than flatbacks. This could lower mining costs but also introduce higher dilution rates. Development is in the advanced stages for trialing this method.

Jan 1, 1994

The Porgera Joint Venture commenced production during September 1990. A small tonnage underground mine extracts high grade gold ore using small scale stopes. Conventional drill and blast methods are used for development and production mining. Ground support is effected with Splitset anchors, grouted rebar bolts and grouted cable bolts. Splitsets and grouted rebar can be installed by mechanised means. Vertical crater retreat, slot and massfire, and modified VCR stoping tech- niques are used at Porgera. Stopes are backfilled with a relatively strong cemented rockf ill. Future stope sequences require recovery of pillars beside and under filled stopes.

Jan 1, 1991

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

In undertaking to write a few notes on practical mining in Bendigo, the great quartz mining centre of Victoria, which just now is celebrating its fiftieth anniversary of gold mining, satisfaction must be expressed which is, no doubt, shared by all mining men and inyestors, that Bendigo has not lagged behind other Australian mining districts in the evolution of mining from its crude state, subsequent to the discovery of gold in 185 to its present more perfect state; and though it may be said that it has not yet reached the high pinnacle of perfection towards which advanced science and change of conditions may yet lead it in the course of future progress, yet, what has already been done in this respect, the adoption of the most approved methods appliances and modern machinery, tending towards greater and still greater efficiency, facility, and economy in our mining industry, must be accepted as a guarantee that in tne future as well as in the past, progress in our means of developing our mining resources will ever remain our watchword, by means of which future difficulties will be overcome as well as they have been removed in the past.The adoption of this principal, combined with a study of rigid economy, has raised gold mining here, as well as in other places, from a state of speculation, and sometimes wild speculation, to the status of a solid, stable industry, the strong supportand backbone of the country in which it flourishes. Two of the principal factors which have been to a great extent instrumental in bringing about this satisfactory state, must be specially mentioned.

Jan 1, 1902

From March to May of 1963, the Bureau of Mineral Resources carried out an experimental aeromagnetic survey at Cobar, New South Wales, to field test a proton-precession magnetometer installation in the Cessna aircraft VH-GEO. The Cobar area was chosen as considerable information was already held on the Earth's magnetic field there, which was known to provide a range of anomalous areas that are not excessively disturbed.A procedure for survey flying and methods for processing data were developed during the survey. Contour maps of the aeromagnetic results were produced in the field. The experimental survey was successful in outlining magnetic anomalies in detail.INTRODUCTIONSince 1951 the Bureau of Mineral Resources, Geology and Geophysics (B.M.R.) has carried out an airborne magnetometer exploration programme with DC.3 aircraft carrying fluxgate magnetometer equipment. Recently a proton-precession magnetometer was developed by the Design and Development Group of the B.M.R. for observatory use. One unit modified for airborne use was installed in the Cessna light aircraft, VH-GEO. The Cessna was modified structurally to take the magnetometer, associated bird, and winch gear.The proton-precession magnetometer has many good features.1. It utilises the transistor and associated solid-state devices in its electronics, and hence is light and small.This is the basic feature allowing its installation in a light aircraft. The transistor circuits have a high reliability factor and owing to the card sub-unit...

Jan 1, 1964

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058°C).

Jan 1, 1972

By R Kjar

Globally, it is anticipated that the mineral sands industry will enter a period of short supply. Demand for both titanium dioxide and zircon is forecast to continue increasing, with new projects needed to come on-stream to fill the supply gap. Victoria is well placed under this scenario as a source due to the high quality of its mineral assemblage, its excellent resource grade and the globally significant size of its mineral sands resources.Australia’s mineral sands rich Murray Basin remains under-developed, especially at its extensive Victorian margins. Development to date has not progressed adequately for the reasons of technology difficulty, history of competition with other jurisdictions and the absence of a platform that requires development as a consideration for security of tenure. Victoria’s mineral sands potential is not just about the Murray Basin, in addition, there have been discoveries in the Gippsland Basin and prospective sites in the Gippsland Basin remain under-explored. Key problems included the lack of available ground for potential developers and the intellectual property of solutions to technological problems associated with the fine grained mineral deposits belonging to a previous developer (with patents now expired).As such, the timing is right to re-visit the potential of the Murray Basin as a site for long-term development with high returns based on current and predicted prices.In order to understand why Victoria’s earth resources in general, and mineral sands in particular, remain under-explored and undeveloped, the Department of Primary Industries initiated an internal review of its role in encouraging and supporting investment in the earth resources sector.As a result, the Victorian Government has committed to taking action to encourage effective ground turnover and acknowledges that a new focus on engagement with industry is needed to bring new investment to the State. The revision of the Mineral Resources (Sustainable Development) Act 1990 provides an opportunity for the government to better align its legislative processes with industry project lifecycles and facilitate access to valuable resources that currently remain undeveloped.Victoria has a track record in assisting projects reach development stage. Iluka currently has two operations in the State in addition to its mineral separation plant that is capable of processing HMC from its South Australian operations. Iluka is expected to ramp up its Murray Basin Stage 2 operations with the WRP mine scheduled to come on line in early 2012. Meanwhile, Astron is actively seeking partners for its Donald Mineral Sands project. The project is becoming increasingly attractive given the recent price hike in zircon; Astron has access to an estimated five to 6 Mt of zircon in its Donald WIM 250 deposit.Given its substantial and valuable mineral sands endowments, the State of Victoria should sensibly be the centre of future investment in project development. However, as previously mentioned this is currently not the case. The Government is therefore committed to implementing new measures that protect security of tenure but ensure that genuine companies can access endowments where they have a clear intent to work those resources.

Oct 5, 2011

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Broken Hill Proprietary Company Limited (BHP) started as a silver-lead-zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations spread throughout the world û in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The BHP World Minerals Cannington silver-lead-zinc mine in Queensland, Australia is a return to the cradle of BHPÆs early silver-lead-zinc years. This paper compares the success factors and challenges at Broken Hill and Cannington.

Jan 1, 1998

THE following short paper on the Blair Athol coal-field will no doubt have a twofold interest to members from the fact that its main seam, known as the "Big Seam" of a maximum thickness of 91 ft without a band, is unique, being probably the thickestseam of high-grade clean coal yet known, and also because of the interesting problem it presents the colliery engineer-viz., which system of mining is the best to secure the highest economical extraction.Location - Blair Athol is a mining township in Central Queensland, situated at an altitude of about 1100 ft. above sea-level at the end of a branch railway line 74, miles from Emerald, on the Main Central Western line, and 240 miles by rail from Rockhampton.Geology - The coal-measures appear to lie in a shallow basin of about four or five square miles in area, surrounded on all sides by slates and schists, which are overlaid oh three sides by alluvial deposits of up to 150 ft. in thickness, and on the fourth by a thick basalt bed, as yet unproved, some miles beyond which the auriferous slates outcrop. These alluvial deposits have been largely worked in years past and gave high gold returns, the chief diggings being Clermont and Macdonald's Flats in the south, the Springs and Black Ridge in the north-east, and Yankee Creek and others on the west. The surface of the coal-fields may be described as unbroken, but undulating, with gentle southerly dip, the watercourses opening out into wide flats. The absence of creeks or deep gullies accounts for no outcrops being visible on the surface, and the coal-measures...

Jan 1, 1918

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic-Upper Permian sequence, and has enabled the upper part of the lllawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in the survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the upper part of the llawarra Coal Measures, as revealed by the seismic reflection survey.A synclinal axis striking at approximately 55° has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by combined analysis of seismic and magnetic results.

Jan 1, 1970

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the short wave infrared range of the solar spectrum from 1220 to 2420 nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a quartz-sericite-pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

Raw materials account for over 60 per cent of the cost of hot metal production in classical blast furnaces and the principal cost component is cost of coke. Dependence on coke is a traditional weakness of blast furnace ironmaking and while efforts have been made to evolve alternative ironmaking technologies which do not use coke, such as direct reduction, smelting reduction, and the more recent method of making iron carbide, blast furnaces continue to be the most efficient means of producing bulk hot metal even today. Coal injection, to the extent of 150 - 200 kg/t of hot metal, has been one of the major innovations made in blast furnaces to decrease cost and to reduce the dependence on coke. This has, however, given rise to more stringent coke property requirements (which often means more expensive coke) - a `tail spin' of Sorts!

Jan 1, 1999

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

The structure of the Bulli coal seam at Appin Colliery was detailed by the seismic reflection method. This unusual application of the seismic method was possible because there is a reflector near the seam as was revealed during exploration for petroleum in an area north-west of Appin. The reflector, which was at a depth of 1,500 ft, was shallow by normal reflection survey standards. Measurement of the seismic velocity at two ventilation shafts showed that the reflector was probably the Bulli coal seam. Accurate depth control was established from previous drilling results.INTRODUCTIONAppin Colliery, situated on the Southern Coalfield of N.S.W. (Fig. 1), is being developed to supply coking coal to the Port Kembla steelworks of Australian Iron and Steel Pty. Ltd. The colliery is mechanized and a detailed knowledge of structure, particularly faulting, is important in planning the workings.The Bulli seam, which is approximately 9 ft thick, and between 1,500 ft and 1,800 ft below the surface, is worked in the colliery. It is the uppermost member of the Permian Coal Measures and is overlain by Triassic rocks, which consist of thick sandstone beds containing beds of coloured shales, and which are subdivided into the Narrabeen Group, the Hawkesbury Sandstone, and the Wianamatta Group.In the early stages of development of the colliery, surface geological mapping and diamond drilling provided information on structure. Generalized results of the mapping are shown on Fig. 2. Drilling indicated that the physical and chemical properties of the Bulli seam are relatively constant, and that the seam is nearly horizontal, the average dipbeing about 1 in 25 to the west.

Jan 1, 1965