Search Documents

By N Ozawa, R Kaneko, M Arimit

The Mitsubishi Higashitani limestone mine is a ten million tonne per annum operation located near the city of Kitakyushu on JapanÆs western island of Kyushu. Higashitani is one of the largest limestone mines in Japan and accounts for about five per cent of national production. Blasting practices at the Higashitani mine involve the use of bagged ANFO, dynamite primers and non-electric detonators. Regulations in Japan prohibit the use of site mixed bulk explosives. Blast size is usually around 17 000 tonnes with 20 holes in a single row, two or three blasts are fired per day at a powder factor of between 0.25 and 0.32 kg/m3. As part of a program looking at oversize reduction Mitsubishi, Asahi and Orica agreed to conduct a joint project at the Higashitani mine to investigate the relationship between the powder factor and fragmentation. The first stage of the project was to benchmark the current blasting performance. Five blasts were monitored in each of the 210 (hard rock) and 220 (soft rock) areas of the mine. OricaÆs Powersieve« software was used to measure fragmentation and total rock breaker hours were also recorded for each blast. OricaÆs computer blasting simulation model Sabrex« was used to prepare revised blast designs with a higher powder factor and predict their performance. The performance of these blasts was monitored using the same methods.

Jan 1, 2004

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By S Pfaff, R Rajic

In the case when the number of independent variables is greater, a careful design for carrying out tests has to be made in order to obtain, with the smallest possible number of tests, as much as possible neutral information about the influence of independent variables on the dependent ones. Only on the basis of such design and its statistical analysis it is possible to come to right conclusions about the function of the whole system. The influence of pressure, temperature, humidity and granulation of the coal upon the resistance to pressure and the water absorption of the briquettes has been tested, with the aim to examine how each of the two dependent variables changes depending on the values assumed by any of the four independent variables and which of the mentioned independent variables significantly influences the dependent ones. The full factorial design with 16 experiments and the central composite design with 27 experiments have been applied. The influence of the independent variables upon the dependent ones has been examined by applying the analysis of variance. The influence values of individual factors and their interaction upon the dependent variables have been stated as well as coefficients of curvilinear equation.

Jan 1, 2003

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

Staff turnover percentages on projects in the minerals sector are at levels that would not be accepted in business less than five years ago. While this is being driven in part by the shortage in skills to service the industry there are underlying factors, beyond the increases in remuneration, adding to the turnover. Having identified the five major reasons why people do not stay, this paper confirms that leaders and the various styles are common to all companies. The paper comments briefly on these major reasons and suggests the problem is firmly with management. It also offers possible remedies to reduce the attrition and therefore improve the opportunities for a quality project evaluation.

Jan 1, 2009

The design of drawpoints in caving and stoping mines has a significant impact on the productivity of the operation. Drawpoints must be designed to provide uniform drawdown and maximum recovery of the broken ore within the limits imposed by the dimensions of the stope, the stability of the pillars, the method of draw, material flow characteristics, etc. The design of drawpoints historically relied on the mining engineerÆs experience and intuition. However, in many operations, empirical analyses have also produced important information regarding design geometry. Factors that affect the sizing and spacing of drawpoints are discussed and guidelines are provided for their design in order to obtain maximum recovery of broken ore and reduce hang-ups.

Jan 1, 2000

This paper addresses; land use, rehabilitation and the State/Federal regulatory process, in light of Australia signing various international conventions and agreements in the area of environmental protection. The conventions on biological diversity, climate change and the implications of the Rio and Agenda 21 declarations are examined. The implementation of these initiatives through the Inter-Governmental Agreement on the Environment, and through legistlative mechanisms at Federal and State level is explored.Particular attention is given to the biodiversity strategy in context of the need to integrate economic aspirations and environmental concerns as a basis for sustsainable development. The paper concludes with a brief comparison of the major approval processes in each State, relating to mining environmental issues.

Jan 1, 1992

By Singer RP

The Latrobe Valley brown coal deposits are one of Australia's major energy resources with measured and indicated reserves amounting to some 162 billion tonnes. Economically recoverable reserves are estimated at some 65 billion tonnes, 47 billion tonnes of which are classified as available for mining (VBCC (1983)). These deposits contain one of the lowest grade fuels used anywhere in the world. Typical Net Wet Specific Energy values range from 6 to 9 MJ/kg. Despite the low energy value of the raw coal, the Latrobe Valley deposits represent approximately 90% of Victoria's indigenous non-renewable energy resources. Utilisation of this vast primary energy resource has been a key factor in the economic development of Victoria.

Jan 1, 1990

Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) is a management company, formed in 1989, to manage the assets and operate the Kalgoorlie joint venture for the owner companies Gold Mines of Kalgoorlie Limited (GMK) and Homestake Gold of Australia Limited (HGAL). Mining is still in progress on the 'Golden Mile' and surrounding areas more than 100 years after Paddy Hannan's discovery adjacent to the active Mt Charlotte mine. From 1893 until 30 June 1995 the Kalgoorlie Goldfields has produced approximately 45 million ounces (-1400 tonnes) of gold from mining and treating about 179 million tonnes of ore. This production equates to about 20 per cent of the total Australian gold production and about one per cent of the world's

Jan 1, 1996

The fragmentation of whole rock by blasting has an influence on the subsequent loading, hauling and crushing operations. However, no method of calculating the frag- mentation has yet been developed. This paper gives a method of calculating the fragmen- tation for the simplest form of blasting, i.e. cratering. Cratering consists of the detonation of a spherical charge of explosive in a blasthole breaking to one free surface. This paper gives a method of calculating the extent of the system of radial cracks generated by the explosive in the rock. This system of radial cracks is then used to calculate the fragment size distribution curve from blasting. The calculated curves are shown to be in good agreement with experiment.

Jan 1, 1977

This address was delivered at the Annual Conference Presidential Dinner held in Sydney on 11 July 1988.The Australasian Institute of Mining and Metallurgy brings together, voluntarily, people with a professional interest in the disciplines and skills which are employed in the mineral industry, and in relation to that industry.We come together because we have a mutual interest in improving what is done by the mineral industry, in all its aspects. It is this sense of continuing improvement, of doing better, of doing as well as we can, as our knowledge and skills improve, that unites us in creating and fostering a professional association of likeminded people.We know from our professional training and experience that enormous progress has been made, at an ever-increasing rate, in the mineral industry, particularly this century. We know that the mineral industry has played a very major role in providing the means by which so many more people survive to live longer, healthier ,and more interesting lives, than ever before. Indeed, together with the oil and gas industry, which is an integral part of the mineral industry but has achieved its own commercial distinction, it is fair to claim that the mineral industry has played the major role in providing the means for the advancement of the human, quality of life.We do not need to make any great claims on human society in consequence of our statement of these contributions. The facts, for those who are aware of them, speak for themselves. Our more modest interest, as members of our professional association, is to look to the future, while conscious of our heritage as a guide to what more might be done, in that future.We certainly do not claim that this indisputable contribution made to human welfare by the mineral industry gives us some moral position of superiority from which to claim greater support or understanding from the wider community of people.On the other hand we know that as members of the mineral industry we have a responsibility to do what we can to help other people to be aware of, and to understand the significance of, those facts which will only speak for themselves if we take the trouble to make them known. And we have a number of organisations. The Institute itself, The Australian Mining Industry Council, the various State Chambers of Mines, the industrial relations body, The Australian Mines and Metals Association, and others, each of which in its own way endeavours to add strength to the individual efforts which we each should make.We may look at these facts about our mineral industry as simple dry statistics, even with their undoubtedly improving trends, or we can see them, and portray them to others, as expressing something which is much more. We can portray them as expressing the outcomes of our professional determination to strive to do better, whatever it i,s we find ourselves doing in this mineralindustry.We may seek to describe our efforts as being in pursuit of excellence, or by other such high-sounding phrases, but I prefer to describe those efforts as simply our strivings to make everything we do better next time-much as the dedicated golfer tries to do, but with, may I suggest, more evident success achieved in the mineral industry; which is one reason why I don't try to play golf.May I suggest to you that trying to do better, is very simply the true basis of professionalism? We are trained and practised to see the opportunity for improvement-not to be static in a world which we know is changing so rapidly in every aspect around us. We must be dynamic, which means optimistic, about improving the world in which we find ourselves.

Jan 1, 1988

By T Tran, F Lucien

Supercritical fluids (SCFs) have gained recognition as solvents for the extraction of a wide range of organic materials. Their principle advantages over conventional organic solvents are that they possess much more favourable transport properties and that such properties can be easily altered by adjusting the system temperature and/or pressure. More recently, SCF solvents have been employed in the extraction of metal ions. The direct extraction of metal ions using SCFs such as CO2 is normally not possible due to the charge neutralisation requirement for solubilisation. However, extraction can be achieved with a SCF solvent containing an organic complexing agent as a cosolvent (Laintz et al, 1992; Laintz and Tachikawa, 1994; Dehghani, 1996). The role of the SCF is therefore similar to the role of a diluent in conventional liquid-liquid or solvent extraction processes. In this regard, SC-CO2 is a particularly good diluent since it exhibits good solubility for many organic complexing agents. The extraction of metals with SCF solvents has been examined mainly in the analysis of environmental samples and the treatment of metal contaminated wastes. Nonetheless, some interesting results have been reported recently on the extraction of rare earth metals, which highlight the potential of SCF solvents in mineral processing applications (Laintz and Tachikawa, 1994; Dehghani, 1996).

Jan 1, 2000

The geochemistry of waste rock from mining operations is critical to the development of acidity-related environmental problems during mining operations, and following mine closure. Failure to recognise the potential for waste rock to produce acidic oxidation products may cause mobilisation of heavy metals into ground and surface waters, and create heavy metal levels in soils which are toxic to plants, causing the failure of revegetation programs. Although more usually associated with wet tropical environments, the potential exists for these problems to occur even in and regions such as the Eastern Goldfields region of Western Australia unless appropriate pre-planning is undertaken.Acidity-related mine waste problems can be extremely expensive to rectify, but can be avoided by waste rock characterisation, and pre-planning of waste rock deposition based on this information. Integration of knowledge of waste rock geochemistry with geotechnical engineering, and application to likely problems, is essential for the successful planning and implementation of cost-effective strategies to avoid problems occurring. Pre-planning to avoid problems is likely to be significantly less expensive in most cases than remedial actions to rectify problems after they have occurred, and in fact may involve no additional cost if it requires only rescheduling or redesign of existing or planned Activities.

Jan 1, 1993

Nearly eighteen months ago Newmont Waihi Operations joined with the local district council and members of the Waihi community in the initiation and running of a community liaison forum.   This forum û the Waihi Community Consultative Committee (WCCC) û was set up with the objective of improving communication, providing a forum for discussion and ultimately working through a range of issues relating to the future of the town and district after the projected closure of Martha Mine in late-2006.   After 18 months of meetings where all represented groups have presented their views, the challenge now is to work together to investigate likely options, seek sources of funding, produce business proposals and plan for the future of Waihi in what we call the Golden Legacy Project.   This paper backgrounds the companyÆs experiences to date, the issues the group has addressed and its proposals for the future. Methods employed to set up an effective community liaison forum are considered, drawing on specific examples from the WCCC. The actions and structures required to ensure effective and ongoing community æbuy inÆ at all levels are also discussed.   This paper develops themes addressed in Taking it to the Streets presented in 2003.

Jan 1, 2004

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

The liquid products of low-temperature carbonisation of coal are of variable composition, very much influenced by the rank and type of coal, and process parameters. In general the tar contains a high proportion of phenols and a low proportion of bases. The neutral oil is more analogous to a thermally cracked petroleum oil than to a high temperature tar. Present practice and possible future trends in the production of chemicals and liquid fuels from low temperature tar are reviewed in the light of recent work on the detailed composition of the tar The phenols and aromatics will probably continue to be of most value, with the bases a useful source of spec- ialty products. However the high aliphatic content of the neutral oil (particularly 1-olefins and n-paraffins) is bound to receive more attention for chemicals as well as for liquid Fuels.

Jan 1, 1969