Search Documents

By Bensley C. N

In June 1995, BHP announced that it would build a Hot Briquetted Iron (HBI) plant and associated beneficiation, materials handling and infrastructure facilities at Port Hedland, Western Australia. This plant, the first direct reduction plant in Australia, will convert beneficiated iron ore fines into metallic iron for briquetting into HBI. The reduction plant will be based on the FINMET fluid bed technology jointly developed by Fior de Venezuela and Voest-Alpine Industrienlagenbau. Electric Arc Furnace steelmakers in the Asia Pacific region will be the principal customers for the product. This paper presents an overview of the facilities to be constructed by the project as well as discussing some particular technology and design engineering issues associated with the project.

Jan 1, 1996

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

The results of a systematic geochemical survey of rare elements are applied to elucidate genetic relations in a suite of rocks and to predict the probability of mineralization. The geology, radioactivity, major element geochemistry and classification of the main intrusives are described. The distribution of a group of rare elements, their concentration trends and the bearing these have on the emplacement sequence of the rocks are considered in some detail. The guides for exploration in the Pilanesberg that emerge are listed and some areas which substantiate predictions are described briefly. It is concluded that a study of rare element trends can make a considerable contribution as an exploration tool and for clarifying relations between the members of rock suites.

Jan 1, 1986

THE manufacture of Portland cement on a commercial basis dates back to the year 1824, when Joseph Aspidin, of Leeds, patented his process. It was, however, only within the past 25 years that the cement of to-day commenced its history, and during that period manufacturers have constantly tried to improve the grade of cement.The introduction of the rotary kiln at the opening of this century was the starting point of rapid development in the process of manufacture, and in the quality of the cement produced.Following on the rotary innovation came the wet process. This at first was used only where the raw materials were of a soft nature; but to-day nearly all classes of materials can be treated by this method. Oompared with the dry process, it allows for greater refinement of raw materials, more intimate mixing, better chemical combination, and economy in fuel. Taking advantage of this, the manufacturers in England and America are in a number of cases substituting the wet for the dry process.Subsidiary machinery throughout the factories, such as crushing and grinding mills, have also been vastly improved. The chemists, too, have done their share in the work. Long and careful research has proved the necessity for accurate proportioning of raw materials, thorough mixing, and very careful burning. All these factors combined have given us the product of to-day, which is consistent within very narrow limits, and far superior to that of the beginning of this cement era.

Jan 1, 1926

The Archean Gossan Hill Group at Golden Grove, Western Australia, hosts two potentially economic volcanogenic massive sulphide deposits. The volcanic-sedimentary succession hosting this mineralisation is composed of a facies association which includes the products of rhyodacitic to,andesitic effusive volcanism, mass-flow sedimentation and concentrated hydrothermal fluid discharge, in a deep subaqueous setting. The Tertiary Kuroko deposits of Japan are widely compared to Archean volcanogenic massive sulphide deposits and a comparison of the facies associations hosting this style of mineralisation, in these two successions separated widely in time, allows a refinement of facies models suitable for exploration in ancient successions. The required deep subaqueous environment for the formation of volcanogenic massive sulphide deposits places constraints on the physical processes that can operate during accumulation of the host stratigraphy. Limitations on the operation of physical processes is reflected by the resultant facies association which can be used to characterize suitable volcanic-sedimentary successions in which volcanogenic massive sulphide mineralisation may be present. The facies association includes: (1) proximal effusive volcanic products - lavas and associated autoclastic breccias (2) distal volcanic products - mass-flow resedimented pyroclastic debris (3) background sedimentation - reworked volcanogenic and terrigenous mass-flow sediments and (4) chemical sediments - exhalites including cherts, sulphides and oxides, with perhaps various carbonates and sulphates. Primary pyroclastic deposits are not expected to be present, other than distal water-lain air-fall deposits, derived from shallow to emergent basin margin explosive volcanic centres, which also provide a source for the resedimented pyroclastic debris.

Jan 1, 1987

Downstream value-adding is a strategic issue for a country like Australia, which has a resources-driven sector of a scale that has significant impact on the national economy. The question of why producers are not doing more to ævalue-addÆ is often asked. In Australia this debate takes place within the context of: an era of unprecedented growth in demand for resources driven by the rapid urbanisation of China, India and others;impending legislation and uncertainty around carbon pricing;rapidly rising energy costs;significant supply-side shortages including infrastructure, skills and manufacturing capacity; andsignificant industry consolidation of primary resource producers with commensurate improvements in market power.There are several examples of resource-based industries which have developed their business along the complete value-chain; for example large oil and gas producers successfully span upstream and downstream operations including refining and petro-chemicals as well as retail distribution of fuel and other products. Relevant frameworks that provide insight and understanding into the strategic issues around value-adding are reviewed and examples of the application of these frameworks to companies and industries which have successfully adopted a strategy of integrating along the value-chain, as well as those players who have focused on parts of the value-chain are presented. The issues around value-adding in Australia are then reviewed with reference to these frameworks and it is concluded that the issue is a conflict between the objective companies who wish to maximise financial value versus the desire of governments to increase economic benefits. An approach to aligning these objectives is proposed.

Jan 1, 2008

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

By Hll J. K, Zhang Y. G

The wear mechanisms of impregnated diamond drill bit matrices are complex and believed to be the key point in solving drill bit self-sharpening problems. A method has been developed to find the change in c,, the wear rate of matrices having different fracture toughness K_ at the increment of drill pressure P. The worn surfaces of specimens were placed under a scanning electron microscope to examine the wear patterns and wear mechanisms at different pressures, and were compared with the worn surface of a practical drill bit. A model is proposed that within a wide range of pressures there exist two different wear mechanisms and three wear regions for cemented car- bide matrix materials. In region one (linear region), at low pressure, the major wear mechanism is plastic deformation in which the preferential wear of the binder phase of the matrix results in the loss of WC, tung- sten carbide particles. Wear rate is controlled by hardness, H as Archard's formula predicts. Wear enters region two and three (non-linear region) simultaneously as pressure is being increased. Consequently, wear transfers to fracture mechanism in which micro-fracture occurs at the root of wear grooves and the material is removed mainly in piece and mass. It has been shown fracture toughness K,, plays a more important role than hard- ness H. It is concluded that for a specific drilling condition, the pressure on the matrix should be carefully controlled and a balance between hard- ness and toughness of the material is essential for a steady drilling Condition.

Jan 1, 1989

By Fernando N, Guang LX

Brown coal in Victoria in spite of its substantial reserves is not utilized greatly because of its high moisture content(-65% w/w). Transportation and handling costs of raw brown coal, on an available energy basis are so expensive that 93% of production is burnt for electricity generation on or adjacent to the coal deposit in Victoria. With direct firing of moist brown coal in power stations, approximately 20% of the gross calorific value of the fuse is used to evaporate the water contained in the coal. This energy is lost as vapour with the flue gas which is vented to the atmosphere. Also there is a 25% increase in flue gas volume and the size and cost of most of the units through which it passes must be appropriately larger. Since there are large quantities of water present the flame temperature is significantly reduced. For zero excess air and no air pre-heating the theoretical flame temperatures are: 609'o wow moisture 1450¦C 40% ª ª ª 1790¦C ZOO ª ª ª 1990¦C As a result of this there is a reduction in radiant heat transfer leading to a requirement for a two fold increase in radiant tube area. A boiler of much greater size and cost is thus required to house the additional tubes. Figure 1 illustrates the relative sizes of a boiler fired with 60% moisture brown coal with a boiler or similar output fed with a British bituminous coal, 14% moisture.

Jan 1, 1989

By Mathews K. E, Willstead T. V C

Initial glory holing was followed by sublevel stoping, with a small proportion of total production mined by shrink and cut-and-fill methods.The sublevel stoping method was successfully modified to cater for altering ground conditions encountered at increasing depths. At present, 94 per cent of production comes from sublevel stopes. The evolution of this mining method and current techniques and practices is outlined. A combined shrink and,sublevel benching method was also developed to increase the mining rate of narrow orebodies over the standard stoping lift of 380 ft. Pillar recovery and stope filling operations have been continuously modified to suit the relIuirements of a rapidly developing mine.INTRODUCTIONOre production commenced at Mount Isa Mines in June 1931. Since then production has increased from approximately 2,500 tons of lead ores per mine day to the current 11,000 tons of sulphide ores per mine day comprising 3,100 tons of lead ore and 7,900 tons of copper ore. The early planners selected sublevel stoping with ring drilling for ore breaking as the most efficient and economical for Mount Isa conditions: This method satisfied requirements for:1. a low cost mining method for the comparatively low grade ores,2. a stoping sequence allowing development, stope preparation, breaking and drawing of ore to proceed concurrently,3. a method of extraction in which broken ore in the stopes would be kept to a minimum because of adverse effects of oxidation on mill metallurgy and...

Jan 1, 1961

It is suggested that if adequate knowledge is available about classifiers in closed grinding circuits, these units may be used as on-stream size analysers when equipped with suitable sensing devices. Research work which is at present in progress to enable a hydrocyclone to be used for this purpose is discussed.

Jan 1, 1967

By Hawes GW

Until 1980 copper, lead and zinc sulphide slurries have been success- fully dewatered for rail and sea transport for many years at the Rose- bery site of North Broken Hill Holdings Ltd. utilizing conventional vacuum disc filtration systems. An upgrading and mill expansion program completed in 1981, which also permitted the introduction of ore streams changes, had resulted in difficulties dewatering copper and lead sulphide slurries to comply with transportable moisture limits. Following an extensive investigation which included both laboratory and pilot plant testing a program was commenced to replace the 2 vacuum disc filtration systems with 2 pressure filtration systems for use on copper and lead slurry dewatering and also to retain other existing vacuum disc filters as standby. An analysis of mill operations performance resulted in slurry storage tanks with a capacity equivalent to 20 hours of normal production being incorporated into the project. The pressure filters are mounted above the concentrate stock- piles. A sealed sloping floor incorporating launders is used to prevent any accidental contamination of the concentrate from pipe leakages, spillage, or from water hoses used for clean up purposes around the area. The project was completed in 1985 and operating performance has been better than that predicted from testwork. Equipment availability at 95076 together with the slurry storage capacity provided results in minimal requirement for the standby vacuum filtration system. Some typical operating results are given.

Jan 1, 1988

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

This paper presents the results of studying the influence of catastrophic failures arising in mines, on the behaviour of mine ventilation systems. It is very important to take account of this influence for the stable operation of the system and to ensure mine safety when mining underground coal and ore deposits.

Jan 1, 2003

Selective leach analytical techniques applied to surface geochemical samples in the search for deeply buried mineral resources gained popularity in the late 1990s. Several commercial assay laboratories introduced their own selective leach methods, adding to the few established commercial methods at that time. Many of these laboratories promoted their methods with orientation data showing favorable responses to both precious and base metal mineralisation, concealed beneath extensive thicknesses of overburden. However, many explorationists remain confused about the utility of these geochemical methods. This confusion is due primarily to the lack of objective orientation surveys over significant mineralisation, comparing all commercially available selective leach methods and to the lack of a creditable theory explaining the formation of these selective leach anomalies. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. An orientation survey was designed to fill the first void û an objective survey over significant mineralisation. With the help of 17 mining companies and assay laboratories, an orientation survey was conducted over five significant covered gold deposits in Nevada, USA , representing over ten million ounces of gold. Hopefully the results of this survey will help provide fuel for those working on the second void û a theory to adequately explain the formation of these selective leach anomalies.

Jan 1, 2008

By C Chen, W J. Bruckard, F R. A Jorge

The base metal industry mines and processes hundreds of million tonnes of ore per annum to produce saleable products and large tonnages of waste by-products such as tailings. These ores usually contain less than 1 wt per cent of toxic elements (As, Sb, Bi, Cd, Se, Te, Hg, etc), which are subsequently treated with the other components in the ore during the production of concentrate through to saleable metal products. The deportments of minor elements across the various unit operations of a process flow sheet do not normally receive the attention that the major elements receive. However, these minor elements can have a major influence on the quality of the products as well as an economic and environmental impact. Therefore, a high degree of control over their deportments is a key step in reducing their dispersion in the biosphere. Ongoing work at CSIRO has been examining minor element deportments across unit processes used for smelting and refining and the options for early removal of minor elements, as well as methods for safe disposal of some toxic elements. This paper provides an overview of the R&D activities undertaken at CSIRO to develop tools and methodologies for improved management of minor elements during the processing of sulfide ores.

Jan 1, 2006

When a joint venture is established between a major and a minor, the co-venturers often have a number of divergent interests; the major may have put up significantly more capital into the project and will want to protect its investement; the major may have more financial resources and be more readily to commit capital to the project; the major may have more technical resources and expertise to provide to the project; the major may have other competing demands for its capital; the minor may be relying on rapid development of the project as its sole source of cash flow. Successful joint ventures arise when the co-venturers understand each others' interests and attempt to satisfy these interests. This could be achived by having a clear process and timetable for development of the project coupled with clear rules for distribution of income, the commitment of capital to the project and the provision of inter-company services. If divergent interests are either regulated clearly or eliminated, both co-venturers are more likely to seek common objectives in the joint venture with less scope for conflict. This paper, written from the perspective of a major, examines means of establishing successful joint ventures between majors and minors.

Jan 1, 1997

During the past decade geopolymer technology has emerged as a possible solution for the effective stabilisation and solidification of waste materials. Amorphous to semi-crystalline geopolymers form by the co-polymerisation of individual alumino and silicate species, which originate from the dissolution of silicon and aluminium containing source materials at a high pH in the presence of soluble alkali metal silicates. It has been shown previously that geopolymerisation can transform a wide range of waste alumino-silicate materials such as fly ash and blast furnace slag into building and mining products with excellent chemical and physical properties, including high compressive strength as well as fire and acid resistance. These chemical and physical properties suggest that geopolymeric matrices derived from waste materials are well suited for environmental and other applications such as the encapsulation of mine tails, the immobilisation of heavy metals and also the fabrication of structural products. The current challenge is to demonstrate that a wide variety of natural Al-Si minerals could serve as potential source materials for the synthesis of geopolymers. Moreover, it should be shown on a large commercial scale that it is possible to encapsulate waste materials into the geopolymeric structure without compromising the chemical and physical properties of the final product for the desired application.

Jan 1, 2000